The effect of five kinds of surface treatment agents on the bond strength to various ceramics with thermocycle aging.

abstract：:Initial attachment of human oral keratinocytes (HOKs) cultured on mirror-surfaced commercially pure titanium (Ti) or yttria-stabilized tetragonal zirconia polycrystals (TZP) was investigated. Numbers of viable attached HOKs, their mRNAs and proteins expression of laminin γ2 and integrin β4 were evaluated using the WST...

journal_title：Dental materials journal

authors： Kimura Y,Matsuzaka K,Yoshinari M,Inoue T

更新日期：2012-01-01 00:00:00

abstract：:This study examined the effect of air abrasion and thermocycling on the adaptation and shear bond strength, of composite resin bonded to dentin using etch-and-rinse and self-etch resin adhesives. Confocal microscopy showed both adhesives closely adapted to dentin and a significantly (p<0.001) greater number of resin t...

journal_title：Dental materials journal

authors： Freeman R,Varanasi S,Meyers IA,Symons AL

更新日期：2012-01-01 00:00:00

abstract：:An experimental primer was developed as a single-step bonding system for resin-modified glass ionomer cements (GIC). Efficacy of this primer on adhesion of resin-modified GICs and resin composite to enamel and dentin was evaluated by shear bond test and SEM observation. Good bond strengths to enamel were obtained (> 1...

journal_title：Dental materials journal

authors： Nikaido T,Nakajima M,Higashi T,Kanemura N,Pereira PN,Tagami J

更新日期：1997-06-01 00:00:00

abstract：:The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...

journal_title：Dental materials journal

authors： Doi K,Kubo T,Hayashi K,Imura K,Akagawa Y

更新日期：2007-03-01 00:00:00

abstract：:This study investigated the efficacies of adhesive resin cements (Clearfil SA Luting, Maxcem, G-CEM, RelyX Unicem Clicker, Vitremer Paste) for bonding to Ag-Pd-Cu-Au alloy not surface-pretreated with metal primer. For control, Panavia F 2.0 -developed for use with a proprietary metal primer, Alloy Primer- was tested w...

journal_title：Dental materials journal

authors： Muraguchi K,Minami H,Minesaki Y,Suzuki S,Tanaka T

更新日期：2011-01-01 00:00:00

abstract：:This study examined the antimicrobial/antifungal ability of a tissue conditioner containing a photocatalyst for Escherichia coli, Streptococcus mutans, Staphylococcus aureus and Candida albicans. The photocatalyst was mixed with tissue conditioners powders at concentrations of 0, 10, 15, and 20 wt%. Tissue conditioner...

journal_title：Dental materials journal

authors： Uchimaru M,Sakai T,Moroi R,Shiota S,Shibata Y,Deguchi M,Sakai H,Yamashita Y,Terada Y

更新日期：2011-01-01 00:00:00

abstract：:Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to i...

journal_title：Dental materials journal

authors： Tanimoto Y,Nagakura M

更新日期：2018-11-30 00:00:00

abstract：:The purpose of this study was to investigate the effect of modifying aluminum oxide slips with magnesium oxide (MgO) to create a jointing material for In-Ceram Alumina. Jointed In-Ceram Alumina bars with In-Ceram Alumina slips containing 0-1.0 mass% MgO were examined by a three-point bending test. Joint-free bars were...

journal_title：Dental materials journal

authors： Odatsu T,Sawase T,Kamada K,Taira Y,Shiraishi T,Atsuta M

更新日期：2008-03-01 00:00:00

abstract：:High-power light-curing units have emerged that reduce the time of procedures in dental clinical work. However, patients sometimes complain of pain during the polymerization of composite resin. In this experiment, we investigated how differences in light-curing mode affect the temperature rise during composite resin p...

journal_title：Dental materials journal

authors： Hori M,Fujimoto K,Asakura M,Nagase Y,Mieki A,Kawai T

更新日期：2019-07-31 00:00:00

abstract：:Oral bacteria adhered to dental material surfaces are known to cause various oral diseases. This study aimed to develop a highsensitive and non-radioisotopic fluorescence dye method for quantification of oral bacteria (Streptococcus, Actinomyces and Veillonella) adhered to denture material surfaces. The amount of adhe...

journal_title：Dental materials journal

authors： Sakuma Y,Washio J,Sasaki K,Takahashi N

更新日期：2013-01-01 00:00:00

abstract：:The objective of this study was to evaluate, using methylene blue (MB), the effects of various light sources on the bleaching action of hydrogen peroxide (H(2)O(2)) with two titanium dioxide (TiO(2)) photocatalysts - an ultraviolet light-activated TiO(2) photocatalyst (UVTiO(2)) versus a visible light-activated TiO(2)...

journal_title：Dental materials journal

authors： Suyama Y,Otsuki M,Ogisu S,Kishikawa R,Tagami J,Ikeda M,Kurata H,Cho T

更新日期：2009-11-01 00:00:00

abstract：:This study investigated the anti-demineralization effects of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes. Thirty-five bovine root specimens were divided into five treatment groups, with seven specimens each coated with 1) MI varnish (MIV), 2) F varnish (FV), 3) PRG varnish I (PV), 4) PRG varn...

journal_title：Dental materials journal

authors： Shiiya T,Kataoka A,Tomiyama K,Fujino F,Mukai Y

更新日期：2020-11-11 00:00:00

abstract：:The purpose of this study was to investigate the effect of laser irradiation on the enamel surface spectroscopically. Polished bovine enamel surface was irradiated with an Er:YAG laser apparatus and chemically analyzed using X-ray photoelectron spectroscopy (XPS). XPS detected core electron peaks such as carbon (C 1s)...

journal_title：Dental materials journal

authors： Mine A,Yoshida Y,Suzuki K,Nakayama Y,Yatani H,Kuboki T

更新日期：2006-06-01 00:00:00

abstract：:The aim of this study was to evaluate the pH at the surface of active or arrested carious dentin using a micro pH sensor, and to compare the relationship between different pH measurement techniques. Twenty extracted carious teeth were divided into two groups, active or arrested caries, according to predefined clinical...

journal_title：Dental materials journal

authors： Murakami K,Kitasako Y,Burrow MF,Tagami J

更新日期：2006-09-01 00:00:00

abstract：:The microstructure and homogeneity of three commercial dentin and incisal unfired porcelain frits (one conventional and two ultra-low fusing types, fused-to metal were analyzed by X-ray diffractometry, scanning electron microspectroscopy, and wavelength- and energy dispersive X-ray microspectroscopy. The average conte...

journal_title：Dental materials journal

authors： Ban S,Matsuo K,Mizutani N,Iwase H,Kani T,Hasegawa J

更新日期：1998-12-01 00:00:00

abstract：:The depths of cure and the distributions of degree of conversion (DC), polymerization conversion (PC) and percent pendant double bonds (PDB) of light-cured composite resins cured under various intensities of light were investigated. When the total amount of exposure, represented by the product of the light intensity a...

journal_title：Dental materials journal

authors： Nomoto R,Uchida K,Hirasawa T

更新日期：1994-12-01 00:00:00

abstract：:The aim of this study was to estimate the flexural properties of three kinds of experimental fiber-reinforced composite (FRC) posts and to evaluate their potential use as posts. Experimental FRC posts were fabricated with glass, aramid, and UHMWP fibers. Commercial FRC posts were used for comparison. A three-point ben...

journal_title：Dental materials journal

authors： Kim MJ,Jung WC,Oh S,Hattori M,Yoshinari M,Kawada E,Oda Y,Bae JM

更新日期：2011-01-01 00:00:00

abstract：:Although titanium has been widely used in prosthetic appliances, such as cast removable partial denture frameworks, high quality castings are still difficult to obtain. This study proposes a new partition technique using a metal foil for improving castability of a two-chamber pressure casting unit. The metal foil was ...

journal_title：Dental materials journal

authors： Watanabe K,Okawa S,Kanatani M,Nakano S,Miyakawa O,Kobayashi M

更新日期：2000-09-01 00:00:00

abstract：:We aimed to establish an experimental animal model to evaluate materials for endodontic therapy. We focused on the biocompatibility of new paste-type zinc oxide-eugenol (ZOE) sealer. The results of this sealer were compared with those of conventional powder/liquid ZOE and eugenol-free sealers. The molars of Wistar rat...

journal_title：Dental materials journal

authors： Mutoh N,Tani-Ishii N

更新日期：2011-01-01 00:00:00

abstract：:The secretion of collagen by osteoblasts was observed by scanning electron microscopy (SEM). Osteoblast-like cells were cultured on a CO3apatite-collagen sponge reinforced with a porous HAp frame. After three days' incubation, a number of newly created matrix fibrils, forming a network structure, were observed at the ...

journal_title：Dental materials journal

authors： Hirata I,Nomura Y,Tabata H,Miake Y,Yanagisawa T,Okazaki M

更新日期：2005-09-01 00:00:00

abstract：:This study aimed to determine the influence of sodium hypochlorite (NaOCl) contamination on the microhardness of build-up composites. Fifty-two samples, from each of three build-up materials (LuxaCore Dual, MultiCore flow and Rebilda DC) were prepared. Half of the samples from each material were stored in physiologic ...

journal_title：Dental materials journal

authors： Wegehaupt FJ,Betschart J,Attin T

更新日期：2010-08-01 00:00:00

abstract：:The purpose of this study was to investigate the effect of remaining dentin thickness (RDT) and long term water storage on dentin bond strength in-vitro. Twenty-seven third molars were randomly divided into 3 groups: Clearfil Bond SE ONE (SE1, Kuraray Noritake Dental, Okayama, Japan), G-Bond plus (GB, GC, Tokyo, Japan...

journal_title：Dental materials journal

authors： Ting S,Chowdhury AFMA,Sun J,Kakuda S,Sidhu SK,Yoshida Y,Selimovic D,Sano H

更新日期：2018-07-29 00:00:00

abstract：:Supercritical water was used as a modification method of electrochemically deposited apatite on pure titanium. The apatites were coated on a commercially pure titanium plate using a hydrothermal-electrochemical method. A constant direct current at 12.5 mA/cm2 was loaded for 1 hr at 25, 60, 100, 150 and 200 degrees C i...

journal_title：Dental materials journal

authors： Ban S,Hasegawa J

更新日期：2001-12-01 00:00:00

abstract：:The purpose of this study was to investigate the retention force of complete palate coverage and palate-less dentures made with three polymerization systems (DS system, SR-Ivocap system, microwave polymerization system) in vitro. The retention force between each denture and a polyurethane model by intervening artifici...

journal_title：Dental materials journal

authors： Teraoka F,Nakagawa M,Takahashi J

更新日期：2004-03-01 00:00:00

abstract：:The objective of this study was to clarify the effect of surface topography on osteoblast-like cell behavior on yttria stabilized tetragonal zirconia polycrystals (TZP). Mirror-polished; blasted with 50- or 150-µm alumina (SB50 and SB150); and SB150 acid-etched with hydrofluoric acid (SB150E) were prepared on TZP. Ini...

journal_title：Dental materials journal

authors： Ito H,Sasaki H,Saito K,Honma S,Yajima Y,Yoshinari M

更新日期：2013-01-01 00:00:00

abstract：:The aim of this study was to compare the shear bond strengths (SBS), failure modes (adhesive, cohesive, or mixed), and marginal microleakage occurrence of conventional resin (CR)-based, glass ionomer (GI)-based, and self-adhesive resin (SAR)-based fissure sealants with or without prior phosphoric acid (PA) etching. Fi...

journal_title：Dental materials journal

authors： Simsek Derelioglu S,Yilmaz Y,Celik P,Carikcioglu B,Keles S

更新日期：2014-01-01 00:00:00

abstract：:We investigated the effects of CO2 laser irradiation combined with acidulated phosphate fluoride (APF) application on the demineralization of enamel. APF gel was applied to the buccal enamel of human premolars and CO2 laser was applied. After the specimens were immersed in demineralization solution for 72 h, they were...

journal_title：Dental materials journal

authors： Nakagaki S,Iijima M,Endo K,Saito T,Mizoguchi I

更新日期：2015-01-01 00:00:00

abstract：:This study evaluated the irrigation extrusion and smear layer (SL) removal of continuous ultrasonic irrigation (CUI). Forty root canals were shaped, embedded in warm sterile saline agar colored with 1% acid red, and distributed into four groups; three groups had the final irrigation sequence of sodium hypochlorite and...

journal_title：Dental materials journal

authors： Jamleh A,Suda H,Adorno CG

更新日期：2018-01-30 00:00:00

abstract：:This study evaluated and compared the influence of different supporting abutment models on the fracture loads of three-unit fixed dental prostheses (FDPs) fabricated from the following materials (n=24/material): (i) IPS e.max CAD-on, (ii) IPS e.max ZirCAD, and (iii) Telio CAD. Twelve FDPs of each group were adhesively...

journal_title：Dental materials journal

authors： Wimmer T,Erdelt KJ,Eichberger M,Roos M,Edelhoff D,Stawarczyk B

更新日期：2014-01-01 00:00:00

abstract：:The purpose of this study was to clarify the effect of silver nanoparticles on the behavior of subcritical crack growth (SCG) in dental porcelains. Prior to occurrence of fast fracture in dental porcelains, SCG occurs and leads to strength degradation over time. SCG in dental porcelains can be characterized by the str...

journal_title：Dental materials journal

authors： Fujieda T,Uno M,Ishigami H,Kurachi M,Kamemizu H,Wakamatsu N,Doi Y

更新日期：2013-01-01 00:00:00