Microstructure and homogeneity of dental porcelain frits.

abstract：:This study compared differences in discoloration and dissolution in several titanium alloys with immersion in peroxide- or fluoride-containing solution. Commercially pure titanium (CP-Ti) and six titanium-based alloys were used: Ti-0.15Pd, Ti-6Al-4V, Ti-7Nb-6Al, Ti-55Ni, Ti-10Cu, and Ti-20Cr. Two test solutions were p...

journal_title：Dental materials journal

authors： Noguchi T,Takemoto S,Hattori M,Yoshinari M,Kawada E,Oda Y

更新日期：2008-01-01 00:00:00

abstract：:This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...

journal_title：Dental materials journal

authors： de Carvalho RF,Martins ME,de Queiroz JR,Leite FP,Ozcan M

更新日期：2011-01-01 00:00:00

abstract：:The purpose of this study was to investigate the retention force of complete palate coverage and palate-less dentures made with three polymerization systems (DS system, SR-Ivocap system, microwave polymerization system) in vitro. The retention force between each denture and a polyurethane model by intervening artifici...

journal_title：Dental materials journal

authors： Teraoka F,Nakagawa M,Takahashi J

更新日期：2004-03-01 00:00:00

abstract：:Photocatalytic activity from the reaction of titanium oxide with ultraviolet light has recently gained much attention. In particular, there is scientific interest in inducing photocatalytic reactions on Ti-Ni alloy, a material widely used in orthodontic applications. However, it is believed that inducing a photocataly...

journal_title：Dental materials journal

authors： Horiuchi Y,Horiuchi M,Hanawa T,Soma K

更新日期：2007-11-01 00:00:00

abstract：:The aim of this in vitro study was to evaluate the effects of different preparation angles on the precision of fit of zirconia crown frameworks. Dies were fabricated with three different preparation angles: 4, 8, and 12 degrees total taper. Ten copings were fabricated for each angle by a laboratory and a milling-cente...

journal_title：Dental materials journal

authors： Beuer F,Edelhoff D,Gernet W,Naumann M

更新日期：2008-11-01 00:00:00

abstract：:This study evaluated the effect of adding silane coupling agent on initial and long-term bond strengths of one-step self-etch adhesives to enamel-dentin-composite in combined situation. Cervical cavities were prepared on extracted molars and filled with Clearfil AP-X. After water-storage for one-week, the filled teeth...

journal_title：Dental materials journal

authors： Mamanee T,Takahashi M,Nakajima M,Foxton RM,Tagami J

更新日期：2015-01-01 00:00:00

abstract：:The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...

journal_title：Dental materials journal

authors： Doi K,Kubo T,Hayashi K,Imura K,Akagawa Y

更新日期：2007-03-01 00:00:00

abstract：:Besides micro-mechanical interlocking through hybrid-layer formation, self-etch adhesives may benefit from additional chemical interaction between the functional monomer and residual hydroxyapatite. One-step adhesives are commonly associated with lower bonding effectiveness, which must be attributed in part to the dis...

journal_title：Dental materials journal

authors： Van Meerbeek B,Van Landuyt K,De Munck J,Hashimoto M,Peumans M,Lambrechts P,Yoshida Y,Inoue S,Suzuki K

更新日期：2005-03-01 00:00:00

abstract：:Initial attachment of human oral keratinocytes (HOKs) cultured on mirror-surfaced commercially pure titanium (Ti) or yttria-stabilized tetragonal zirconia polycrystals (TZP) was investigated. Numbers of viable attached HOKs, their mRNAs and proteins expression of laminin γ2 and integrin β4 were evaluated using the WST...

journal_title：Dental materials journal

authors： Kimura Y,Matsuzaka K,Yoshinari M,Inoue T

更新日期：2012-01-01 00:00:00

abstract：:This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...

journal_title：Dental materials journal

authors： Fujita R,Komada W,Nozaki K,Miura H

更新日期：2014-01-01 00:00:00

abstract：:The objective of this study was to clarify the effect of surface topography on osteoblast-like cell behavior on yttria stabilized tetragonal zirconia polycrystals (TZP). Mirror-polished; blasted with 50- or 150-µm alumina (SB50 and SB150); and SB150 acid-etched with hydrofluoric acid (SB150E) were prepared on TZP. Ini...

journal_title：Dental materials journal

authors： Ito H,Sasaki H,Saito K,Honma S,Yajima Y,Yoshinari M

更新日期：2013-01-01 00:00:00

abstract：:The aim was to investigate the effect of simulated low-temperature degradation (s-LTD) and hydrothermal fatigue on the degradation of three ZrO(2)-based dental materials. Lava, IPS, and NanoZr discs were randomly assigned to (1) Control-Storage in distilled water at 37°C; (2) Aging at 134°C for 5 h (s-LTD); (3) Thermo...

journal_title：Dental materials journal

authors： Perdigão J,Pinto AM,Monteiro RC,Braz Fernandes FM,Laranjeira P,Veiga JP

更新日期：2012-01-01 00:00:00

abstract：:This study aimed to evaluate the effect of sulfinic acid sodium salt interposition after acid and sodium hypochlorite treatment (NC treatment) on dentin bonding durability using a mild type one-step self-etching adhesive. Fifteen human third molars were randomly assigned into three experimental groups according to den...

journal_title：Dental materials journal

authors： Nakatani H,Mine A,Matsumoto M,Kabetani T,Kawaguchi-Uemura A,Higashi M,Tajiri Y,Imai D,Hagino R,Minamino T,Miura J,Yatani H

更新日期：2017-11-29 00:00:00

abstract：:This study determined the discoloration of five CAD/CAM resins, four manually polymerized resins, and glass-ceramic as control group. Specimens were divided into three groups (N=300, n=30) to be stored in coffee, black tea and red wine (n=10). The discoloration was measured using a spectrophotometer after 1, 7, 29, 90...

journal_title：Dental materials journal

authors： Stawarczyk B,Sener B,Trottmann A,Roos M,Ozcan M,Hämmerle CH

更新日期：2012-01-01 00:00:00

abstract：:This study examined the surface microhardness of four kinds of resin composites with different fillers and resin matrices. Ten specimens of 2 mm thickness and 4 mm diameter of each resin composite were polymerized using a halogen light, a blue light-emitted diode, and a plasma arc unit. Microhardness evaluation was pe...

journal_title：Dental materials journal

authors： Hubbezoğlu I,Bolayir G,Doğan OM,Doğan A,Ozer A,Bek B

更新日期：2007-11-01 00:00:00

abstract：:The relation between the bonding efficacy of the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated. The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized 0.5 M EDTA...

journal_title：Dental materials journal

authors： Chiba M,Itoh K,Wakumoto S

更新日期：1989-06-01 00:00:00

abstract：:The depths of calcium-ion incorporation into a commercially pure titanium and an experimental beta-type titanium alloy were determined using Auger electron spectroscopy. After the electrochemical deposition of apatite, new compositional gradients appeared in the profiles in which the Ca and P concentrations gradually ...

journal_title：Dental materials journal

authors： Ban S,Kamiya A,Sonoda T

更新日期：2002-12-01 00:00:00

abstract：:To evaluate the cytotoxicity of resin cements on dental pulp-derived cells (bDPCs), Bifix QM (BQM), Choice 2(C2), RelyX U200(RU200), Maxcem Elite(ME), and Multilink Automix(MA) were tested. The materials were incubated in DMEM for 72 h. A real-time cell analyzer was used to evaluate cell survival. The statistical anal...

journal_title：Dental materials journal

authors： Arslan Malkoç M,Demir N,Şengün A,Bozkurt ŞB,Hakki SS

更新日期：2015-01-01 00:00:00

abstract：:The aim of this investigation was to evaluate the metal-ceramic bonding of Au-1.6 wt% Ti alloy. Therefore, the coefficient of thermal expansion, modulus of elasticity, ceramic bonding strength, and hardness of Au-1.6 wt% Ti alloy were measured. The metal-ceramic interface was observed by EPMA to investigate its bondin...

journal_title：Dental materials journal

authors： Ito M,Kikuchi M,Okuno O,Kimura K

更新日期：2005-06-01 00:00:00

abstract：:This in vitro study aimed to evaluate the effect of two different polymer-based CAD/CAM materials; resin-nano ceramic (Lava Ultimate [LVU]) and composite (CERASMART [CS]), their different surface pre-treatments, and use of different resin cements on the µTBS of adhesively bonded CAD/CAM onlays to dentin. CAD/CAM mater...

journal_title：Dental materials journal

authors： Capa N,Say EC,Celebi C,Casur A

更新日期：2019-02-08 00:00:00

abstract：:The fluorescence and physical properties of thulium-doped zirconia were investigated. A standard grade of zirconia (TZ-3Y-E) and two translucent dental zirconia materials (Zpex and Zpex Smile) were examined. The specimens were prepared by addition of 0-1.5 wt% Tm2O3 and then sintering. When exposed to UV light, the Tm...

journal_title：Dental materials journal

authors： Nakamura T,Okamura S,Nishida H,Usami H,Nakano Y,Wakabayashi K,Sekino T,Yatani H

更新日期：2018-11-30 00:00:00

abstract：:The aim was to characterize by atomic force microscopy (AFM) the nanostructure of human dentin surfaces affected by dental fluorosis (DF) before and after phosphoric acid etching. This study included 240 human dentin samples classified according to the severity of DF, which were divided into four groups using the Thyl...

journal_title：Dental materials journal

authors： Zavala-Alonso V,Aguilera-Flores R,Patiño-Marin N,Martinez-Castañon GA,Anusavice KJ,Loyola-Rodriguez JP

更新日期：2011-01-01 00:00:00

abstract：:The purpose of this study was to evaluate the effects of acid-etched titanium on the biological responses of osteoblast-like MC3T3-E1 cells. Four types of treatments (polishing, sandblasting, concentrated H2SO4 etching, and concentrated H2SO4 etching with vacuum firing) were carried out on the surfaces of commercially...

journal_title：Dental materials journal

authors： Iwaya Y,Machigashira M,Kanbara K,Miyamoto M,Noguchi K,Izumi Y,Ban S

更新日期：2008-05-01 00:00:00

abstract：:This study investigated the durability, especially the nonwaterdegradable qualities, of experimental light-cured composite resin containing barium-borosilicate glass filler. For this purpose, Bis-GMA, a typical component of base monomer in conventional composite resin, was replaced by Bis-GMA-F which is water-repellen...

journal_title：Dental materials journal

authors： Tanaka J,Inoue K,Masamura H,Matsumura K,Nakai H,Inoue K

更新日期：1993-06-01 00:00:00

abstract：:The purpose of this study was to investigate the effect of laser irradiation on the enamel surface spectroscopically. Polished bovine enamel surface was irradiated with an Er:YAG laser apparatus and chemically analyzed using X-ray photoelectron spectroscopy (XPS). XPS detected core electron peaks such as carbon (C 1s)...

journal_title：Dental materials journal

authors： Mine A,Yoshida Y,Suzuki K,Nakayama Y,Yatani H,Kuboki T

更新日期：2006-06-01 00:00:00

abstract：:The purpose of this study was to examine the effect of an electro-ionizing toothbrush with stannous fluoride in the treatment of dentin hypersensitivity following periodontal surgery. Thirty-two volunteers with dentin hypersensitivity were divided in two equal groups each using different methods: (Group I) stannous fl...

journal_title：Dental materials journal

authors： Orbak R,Canakçi V,Tezel A

更新日期：2001-06-01 00:00:00

abstract：:The effect of etching for 90 s with low concentrations (0.5, 1.0, 2.0, 3.0, 3.5, and 4.0%) of hydrofluoric acid (HF) on the adhesiveness of computer-aided design/computer-aided manufacturing (CAD/CAM) resin blocks [CERASMART (CS), SHOFU BLOCK HC (HC), KATANA AVENCIA Block(KA), and VITA ENAMIC (EN)] was investigated. E...

journal_title：Dental materials journal

authors： Niizuma Y,Kobayashi M,Toyama T,Manabe A

更新日期：2020-12-03 00:00:00

abstract：:The purpose of this study was to evaluate the effect of different polymerization cycles on the flexural strengths and microhardness of two denture base materials (Meliodent and Paladent). Heat-polymerized acrylic resin specimens (65.0 mm long×10.0 mm wide×2.5 mm in height) were prepared using different short and long ...

journal_title：Dental materials journal

authors： Gungor H,Gundogdu M,Alkurt M,Yesil Duymus Z

更新日期：2017-03-31 00:00:00

abstract：:Thermal misfit is deemed as one reason for the chipping of veneered zirconia restorations. Aim of the present study was to assess the effect of thermal misfit on the fracture load of veneered zirconia frameworks and to evaluate the applicability of a universal veneering ceramic for both zirconia and titanium framework...

journal_title：Dental materials journal

authors： Fischer J,Stawarczyk B,Tomic M,Strub JR,Hämmerle CH

更新日期：2007-11-01 00:00:00

abstract：:Effects of functionally gradient calcium phosphate consisting of hydroxyapatite (HAP) and alpha-tricalcium phosphate (alpha-TCP) on proliferation and differentiation of osteoblasts were evaluated using MC3T3-E1 cells. There were no significant differences in the proliferation of MC3T3-E1 cells among HAP-alpha-TCP func...

journal_title：Dental materials journal

authors： Yuasa T,Miyamoto Y,Kon M,Ishikawa K,Takechi M,Momota Y,Tatehara S,Takano H,Mimamiguchi S,Nagayama M

更新日期：2005-06-01 00:00:00