Effect of sodium hypochlorite contamination on microhardness of dental core build-up materials.

Abstract:

:This study aimed to determine the influence of sodium hypochlorite (NaOCl) contamination on the microhardness of build-up composites. Fifty-two samples, from each of three build-up materials (LuxaCore Dual, MultiCore flow and Rebilda DC) were prepared. Half of the samples from each material were stored in physiologic saline (baseline control) while the other halves were stored in NaOCl. After 1 h, the samples were rinsed with tap water, cut axially and measured for Knoop hardness at different depth levels. The results were analysed by ANOVA and unpaired t-tests (p<0.05). Significant differences in microhardness were observed for LuxaCore Dual up to 0.2 mm, Rebilda DC up to 0.3 mm, and for MultiCore flow up to 0.4 mm under the surface level. Contact with sodium hypochlorite on build-up materials causes reduction of the microhardness. The softening is not only limited on the surface, but can also be found in deeper layers of build-up materials.

journal_name

Dent Mater J

journal_title

Dental materials journal

authors

Wegehaupt FJ,Betschart J,Attin T

doi

10.4012/dmj.2010-007

subject

Has Abstract

pub_date

2010-08-01 00:00:00

pages

469-74

issue

4

eissn

0287-4547

issn

1881-1361

pii

JST.JSTAGE/dmj/2010-007

journal_volume

29

pub_type

杂志文章
  • Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin.

    abstract::This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal floor dentin were restored with a two-step self-etch adhesive system, Clearfil Liner Bond 2V and a composite core, Cle...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2009-104

    authors: Ariyoshi M,Nikaido T,Foxton RM,Tagami J

    更新日期:2010-10-01 00:00:00

  • Effect of dentin cleansers on the bonding efficacy of dentin adhesive.

    abstract::The relation between the bonding efficacy of the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated. The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized 0.5 M EDTA...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.8.76

    authors: Chiba M,Itoh K,Wakumoto S

    更新日期:1989-06-01 00:00:00

  • Effects of polishing on surface roughness and hardness of glass-fiber-reinforced polypropylene.

    abstract::Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to i...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-012

    authors: Tanimoto Y,Nagakura M

    更新日期:2018-11-30 00:00:00

  • Effect of doxycycline-treated hydroxyapatite surface on bone apposition: A histomophometric study in murine maxillae.

    abstract::Improved osseointegration of dental implants is imperative in clinic. Effect of doxycycline on promoting bone formation after implant placement was expected due to its inhibitory properties on inflammation and osteoclastogenesis. To evaluate new bone formation on the hydroxyapatite (HA)-coated implant surface, which w...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2017-007

    authors: Ding L,Zhang P,Wang X,Hao J,Aoki K,Kuroda S,Kasugai S

    更新日期:2018-01-30 00:00:00

  • Measurement of exothermic heat released during polymerization of a lightcuring composite resin: Comparison of light irradiation modes.

    abstract::High-power light-curing units have emerged that reduce the time of procedures in dental clinical work. However, patients sometimes complain of pain during the polymerization of composite resin. In this experiment, we investigated how differences in light-curing mode affect the temperature rise during composite resin p...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-158

    authors: Hori M,Fujimoto K,Asakura M,Nagase Y,Mieki A,Kawai T

    更新日期:2019-07-31 00:00:00

  • Effects of dose of recombinant human BMP-2 on bone formation at palatal sites in young and old rats.

    abstract::This study was designed to examine the effects of dose of recombinant human BMP-2 (rhBMP-2) on bone formation at palatal sites in 10-week-old (10w) and 70-week-old (70w) rats, when combined with a polylactate-polyglycolate copolymer/gelatine sponge (PGS). New bone formation was observed at six weeks after implantation...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.26.481

    authors: Yamaji K,Kawanami M,Matsumoto A,Odajima T,Nishitani Y,Iwasaka K,Yoshimitsu K,Yoshiyama M

    更新日期:2007-07-01 00:00:00

  • In vivo effect of fluoride-substituted apatite on rat bone.

    abstract::Different types of calcium phosphate compounds are commercially available for medical and dental applications as bone substitute materials. Biological apatites contain several kinds of minor elements such as carbonate (CO3), magnesium (Mg), and fluoride (F) in enamel, dentin, and bone. It has been shown that F ion and...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.24.398

    authors: Inoue M,Nagatsuka H,Tsujigiwa H,Inoue M,LeGeros RZ,Yamamoto T,Nagai N

    更新日期:2005-09-01 00:00:00

  • Influence of a denture strengthener on the deformation of a maxillary complete denture.

    abstract::The present study investigated the influences of a denture strengthener on the deformation of a maxillary complete denture. Three groups of maxillary complete dentures were fabricated (Group 1 without a strengthener; Group 2 with a Co-Cr alloy wire strengthener; Group 3 with an experimental fiberglass strengthener). T...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.28.507

    authors: Hirajima Y,Takahashi H,Minakuchi S

    更新日期:2009-07-01 00:00:00

  • Cold plasma-induced surface modification of heat-polymerized acrylic resin and prevention of early adherence of Candida albicans.

    abstract::Atmospheric-pressure cold plasma was applied to process the surface of heat-polymerized acrylic resin. Changes to the physical properties and early adherence of Candida albicans were investigated. Alternating current cold plasma with Ar/O2 as working gas was used. Scanning electron microscopy (SEM) and X-ray photoelec...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-035

    authors: Pan H,Wang G,Pan J,Ye G,Sun K,Zhang J,Wang J

    更新日期:2015-01-01 00:00:00

  • Effects of fluoride and dissolved oxygen concentrations on the corrosion behavior of pure titanium and titanium alloys.

    abstract::The effects of dissolved-oxygen concentration and fluoride concentration on the corrosion behaviors of commercial pure titanium, Ti-6Al-4V and Ti-6Al-7Nb alloys and experimentally produced Ti-0.2Pd and Ti-0.5Pt alloys were examined using the corrosion potential measurements. The amount of dissolved Ti was analyzed by ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.21.83

    authors: Nakagawa M,Matsuya S,Udoh K

    更新日期:2002-06-01 00:00:00

  • Assessment of mechanical properties of WaveOne Gold Primary reciprocating instruments.

    abstract::This study aimed to evaluate cyclic fatigue resistance and bending properties and torque/force generation of WaveOne Gold (WOG) Primary in comparison with WaveOne (WO) Primary and Reciproc (RE) R25. A cyclic fatigue test revealed that the WOG Primary took significantly longer time to fracture compared with the WO Prim...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-203

    authors: Fangli T,Maki K,Kimura S,Nishijo M,Tokita D,Ebihara A,Okiji T

    更新日期:2019-06-01 00:00:00

  • Changes on NiTi orthodontic wired due to acidic fluoride solution.

    abstract::The effect of acidic fluoride solution on NiTi arch wires was examined by testing crystal structure, tensile strength, morphology after fracture, and element release from wire under four different test solutions after 1 or 3 d immersion. Three-day immersion in a 0.2%/pH 4 solution did not form any new crystal structur...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.23.557

    authors: Kwon YH,Cheon YD,Seol HJ,Lee JH,Kim HI

    更新日期:2004-12-01 00:00:00

  • Influence of mucin pre-adsorption for lipoteichoic acid adsorption on titanium surfaces.

    abstract::We investigated the adsorption of lipoteichoic acid (LTA) on titanium surfaces by using the quartz crystal microbalance (QCM) method, and confirmed the influence of mucin (MUC) pre-adsorption on LTA adsorption. Two injection methods were evaluated. Namely, Method A: single-step injection of LTA solution to the Ti sens...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-209

    authors: Yoshida E,Hayakawa T

    更新日期:2020-12-03 00:00:00

  • Effect of new light curing units on microleakage and microhardness of resin sealants.

    abstract::To determine new developed light curing units with shorter curing times effects on microleakage and microhardness values for resin fissure sealants. Resin filled sealant (UltraSeal-XT), resin unfilled sealant (Delton Type-II) and ormocer-based sealant (Admira-Seal) were light cured with a quartz-tungsten-halogen (QTH)...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-357

    authors: Bani M,Tirali RE

    更新日期:2016-01-01 00:00:00

  • Repair bond strength of bulk-fill resin composite: Effect of different adhesive protocols.

    abstract::This study evaluated the effect of different adhesive protocols on the shear bond strength (SBS) of bulk-fill resin composite repaired with bulk-fill or conventional composite. Cylindrical bulk-fill resin composite specimens were prepared and allocated into groups according to the bonding strategy: no treatment, Silan...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-291

    authors: Cuevas-Suárez CE,Nakanishi L,Isolan CP,Ribeiro JS,Moreira AG,Piva E

    更新日期:2020-03-31 00:00:00

  • A study of in vivo degradation of two vital home bleaching gels.

    abstract::This study investigated hydrogen peroxide (H2O2) concentration of two home bleaching gels, in their dispensing syringes and their degradation in vivo in intraoral bleaching trays. Two bleaching gels were studied, 7.5% hydrogen peroxide (HP) and 20% carbamide peroxide (CP). The concentration of H2O2 was determined in d...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2012-317

    authors: Alonso De La Peña V,Rodriguez Carreira A,Corral Aneiros R,López Ratón M,Guitián Rivera F

    更新日期:2013-01-01 00:00:00

  • Color change of newly developed esthetic restorative material immersed in food-simulating solutions.

    abstract::Recently, an esthetic tooth coating material has been developed. The material consisted of a primer solution, a base coat, and a top coat. The purpose of this study, therefore, was to evaluate the color change of this tooth coating material and two resin composites after immersion in food-simulating, staining solution...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.25.352

    authors: Fujita M,Kawakami S,Noda M,Sano H

    更新日期:2006-06-01 00:00:00

  • Influence of a propolis-based irrigant solution on gap formation and bond strength of posts bonded to root canal dentin using different resin cements.

    abstract::This study evaluated the influence of an aqueous propolis-based solution (PROP) on gap formation and bond strength of posts bonded to root canal dentin using resin cements. Endodontically-treated bovine incisors received different irrigation protocols: 1) 2.5% sodium hypochlorite (NaOCl)/17% EDTA/NaOCl; 2) saline solu...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-111

    authors: Matochek MHM,Tomaz PLS,Oliveira TS,Polassi MR,Alonso RCB,Scremin FM,Sauro S,Marcucci MC,D'Alpino PHP

    更新日期:2020-06-05 00:00:00

  • Durability of diamond burs for the fabrication of ceramic crowns using dental CAD/CAM.

    abstract::The diamond burs of two dental CAD/CAM systems (GN and CD) were examined if they could be used to fabricate up to 21 ceramic full crowns without fracture. After one, 11, and 21 machining times, the surfaces of the diamond burs were observed and the number of particles captured on SEM pictures was counted. The average ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.24.134

    authors: Yara A,Ogura H,Shinya A,Tomita S,Miyazaki T,Sugai Y,Sakamoto Y

    更新日期:2005-03-01 00:00:00

  • Impact of different surface treatments and repair material reinforcement on the flexural strength of repaired PMMA denture base material.

    abstract::This study assessed the impact of surface treatments and repair resin reinforcement with zirconium oxide nano-particles (nano-ZrO2) on flexural strength (FS) of repaired denture base. A total of 320 heat-polymerized acrylic resin specimens were prepared and sectioned creating 2-mm gap. According to repair surface trea...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-436

    authors: Gad MM,Rahoma A,Abualsaud R,Al-Thobity AM,Akhtar S,Helal MA,Al-Harbi FA

    更新日期:2020-06-05 00:00:00

  • Fracture force for veneered materials on restorations measured by torsion testing.

    abstract::The torsional fracture strength at the interface between a base plate and veneering material was evaluated for three kinds of veneered restoration: porcelain fused to zirconia (PFZ), porcelain fused to metal (PFM), and composite resin veneered metal (CRVM). The metal and zirconia base plate (30×4×0.4 mm) were prepared...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2016-432

    authors: Watanabe F,Seto M,Ueda K,Ozawa M

    更新日期:2018-07-29 00:00:00

  • Effectiveness of bonding resin-based composite to healthy and fluorotic enamel using total-etch and two self-etch adhesive systems.

    abstract::The aim of this study was to evaluate the bond strength of three adhesive systems: Excite™, Adper Prompt L-Pop™ and AdheSE One™ to varying degrees of fluorotic enamel using micro-tensile bond strength (μTBS) tests. Human enamel was classified according to the Thylstrup and Fejerskov Index. The interface resin-enamel w...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2012-140

    authors: Torres-Gallegos I,A Martinez-Castañon G,Loyola-Rodriguez JP,Patiño-Marin N,Encinas A,Ruiz F,Anusavice K

    更新日期:2012-01-01 00:00:00

  • Development of casting investment preventing blackening of noble metal alloys part 1. Application of developed investment for Ag-Pd-Cu-Au alloy.

    abstract::The objective of this study is to develop a casting investment that prevents the blackening of the cast surface of noble metal alloys. The experimental investments were prepared using a gypsum-bonded investment in which the metallic powders such as boron (B), silicon (Si), aluminum (Al) and titanium (Ti) were added as...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.22.87

    authors: Kakuta K,Nakai A,Goto S,Wakamatsu Y,Yara A,Miyagawa Y,Ogura H

    更新日期:2003-03-01 00:00:00

  • Effect of adhesive primer developed exclusively for heat-curing resin on adhesive strength between plastic artificial tooth and acrylic denture base resin.

    abstract::Despite progress in the development of denture base resin and artificial tooth materials, dental clinics are still plagued with artificial teeth falling off the denture base--due to poor bond strength--after denture delivery. Against this background, this study sought to examine the effect and durability of an adhesiv...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.25.75

    authors: Nishigawa G,Maruo Y,Okamoto M,Oki K,Kinuta Y,Minagi S,Irie M,Suzuki K

    更新日期:2006-03-01 00:00:00

  • Light activated resin containing organic dyestuff.

    abstract::The physical properties of experimental visible light-activated resins containing dyestuff, which could be quickly discolored by irradiation was, evaluated by analyzing light absorbance characteristics and measuring micro Vickers hardness. The experimental resin, which was prepared by mixing equivalent weights of Bis ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.8.147

    authors: Nakazato J,Itoh K,Wakumoto S

    更新日期:1989-12-01 00:00:00

  • Effects of attrition, prior acid-etching, and cyclic loading on the bond strength of a self-etching adhesive system to dentin.

    abstract::The purpose of this study was to evaluate the effects of dentin attrition, phosphoric acid etching, and cyclic loading on the microtensile bond strength (microTBS) of a self-etching adhesive system to dentin. Flat dentin surfaces of human molars were assigned to eight experimental groups based on those with or without...

    journal_title:Dental materials journal

    pub_type: 杂志文章,随机对照试验

    doi:10.4012/dmj.28.197

    authors: Shinkai K,Ebihara T,Shirono M,Seki H,Wakaki S,Suzuki M,Suzuki S,Katoh Y

    更新日期:2009-03-01 00:00:00

  • Morphological and chemical analysis of different precipitates on mineral trioxide aggregate immersed in different fluids.

    abstract::The purpose of this study was to analyze the ultrastructures and chemical compositions of precipitates formed on mineral trioxide aggregate (MTA; White ProRoot MTA) immersed in distilled water (DW) or phosphate buffered saline (PBS), based on the attribution that MTA's bioactivity and sealing ability are influenced by...

    journal_title:Dental materials journal

    pub_type: 杂志文章,随机对照试验

    doi:10.4012/dmj.2009-133

    authors: Han L,Okiji T,Okawa S

    更新日期:2010-10-01 00:00:00

  • Determination of molecular species of calcium salts of MDP produced through decalcification of enamel and dentin by MDP-based one-step adhesive.

    abstract::Enamel and dentin particles were added to an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step adhesive to react for 30 s. After enamel and dentin reactants were analyzed using X-ray diffraction (XRD) and phosphorus-31 nuclear magnetic resonance ((31)P NMR) techniques, curve-fitting analys...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2014-260

    authors: Yokota Y,Nishiyama N

    更新日期:2015-01-01 00:00:00

  • Irrigation effectiveness of continuous ultrasonic irrigation system: An ex vivo study.

    abstract::This study evaluated the irrigation extrusion and smear layer (SL) removal of continuous ultrasonic irrigation (CUI). Forty root canals were shaped, embedded in warm sterile saline agar colored with 1% acid red, and distributed into four groups; three groups had the final irrigation sequence of sodium hypochlorite and...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2016-411

    authors: Jamleh A,Suda H,Adorno CG

    更新日期:2018-01-30 00:00:00

  • Zirconia ceramics, their contrast ratio and grain size depending on sintering parameters.

    abstract::This study investigated the contrast ratio and grain size depending on sintering parameters of twelve different zirconia materials and compared with glass-ceramic (N=156, n=12 per group). Contrast ratio of all ceramics was measured using a spectrophotometer according to ISO 2471: 2008. Grain sizes of zirconia were det...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2014-056

    authors: Stawarczyk B,Emslander A,Roos M,Sener B,Noack F,Keul C

    更新日期:2014-01-01 00:00:00