Modification of electrochemically deposited apatite using supercritical water.

abstract：:The purpose of this study was to evaluate the effect of different polymerization cycles on the flexural strengths and microhardness of two denture base materials (Meliodent and Paladent). Heat-polymerized acrylic resin specimens (65.0 mm long×10.0 mm wide×2.5 mm in height) were prepared using different short and long ...

journal_title：Dental materials journal

authors： Gungor H,Gundogdu M,Alkurt M,Yesil Duymus Z

更新日期：2017-03-31 00:00:00

abstract：:The influence of a thin carbonate-containing hydroxyapatite (CA) coating to tetragonal zirconia polycrystal (TZP) on osteoblastlike cell response was investigated. TZP disks were subjected to blasting and acid etching. Thin CA coatings were deposited by the molecular precursor method (TZP-CA). Initial cell adhesion of...

journal_title：Dental materials journal

authors： Kaneko H,Sasaki H,Honma S,Hayakawa T,Sato M,Yajima Y,Yoshinari M

更新日期：2014-01-01 00:00:00

abstract：:This study examined the antimicrobial/antifungal ability of a tissue conditioner containing a photocatalyst for Escherichia coli, Streptococcus mutans, Staphylococcus aureus and Candida albicans. The photocatalyst was mixed with tissue conditioners powders at concentrations of 0, 10, 15, and 20 wt%. Tissue conditioner...

journal_title：Dental materials journal

authors： Uchimaru M,Sakai T,Moroi R,Shiota S,Shibata Y,Deguchi M,Sakai H,Yamashita Y,Terada Y

更新日期：2011-01-01 00:00:00

abstract：:The purpose of this study was to investigate the effects of the location and orientation of dentinal tubules in the tooth on tensile strengths of the dentin. Dumbbell-shaped specimens of 12 groups from various locations and dentinal tubule orientations were prepared. The tensile test was performed in distilled water a...

journal_title：Dental materials journal

authors： Inoue T,Takahashi H,Nishimura F

更新日期：2002-03-01 00:00:00

abstract：:An experimental primer was developed as a single-step bonding system for resin-modified glass ionomer cements (GIC). Efficacy of this primer on adhesion of resin-modified GICs and resin composite to enamel and dentin was evaluated by shear bond test and SEM observation. Good bond strengths to enamel were obtained (> 1...

journal_title：Dental materials journal

authors： Nikaido T,Nakajima M,Higashi T,Kanemura N,Pereira PN,Tagami J

更新日期：1997-06-01 00:00:00

abstract：:Improved osseointegration of dental implants is imperative in clinic. Effect of doxycycline on promoting bone formation after implant placement was expected due to its inhibitory properties on inflammation and osteoclastogenesis. To evaluate new bone formation on the hydroxyapatite (HA)-coated implant surface, which w...

journal_title：Dental materials journal

authors： Ding L,Zhang P,Wang X,Hao J,Aoki K,Kuroda S,Kasugai S

更新日期：2018-01-30 00:00:00

abstract：:The aim of this study was to investigate the effect of three metal priming agents on the bond strength of adhesive resin cement to Silver-Zinc-Tin-Indium (Ag-Zn-Sn-In) alloy and pure Ag, Zn, Sn, and In. The specimens were air-abraded with alumina and then primed with one of three metal priming agents: V-Primer, Esteni...

journal_title：Dental materials journal

authors： Imamura N,Kawaguchi T,Shimizu H,Takahashi Y

更新日期：2018-03-30 00:00:00

abstract：:This study investigated transformations of nickel-titanium wires using differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) under tensile load (100 gf or 500 gf). Two nickel-titanium wires, 35°C Copper Ni-Ti and Nitinol SE, were selected. DSC analyses were performed between -90° and 100°C. Speci...

journal_title：Dental materials journal

authors： Iijima M,Ohta M,Brantley WA,Naganishi A,Murakami T,Muguruma T,Mizoguchi I

更新日期：2011-01-01 00:00:00

abstract：:The in vitro dentin permeability of the constituents of two types of conventional phosphoric acid etching agents which had different viscosities, and their pH changes after being permeated dentin were investigated. It was recognized that, even though the etching was for a short time (one minute) followed by rinsing, t...

journal_title：Dental materials journal

authors： Ishikawa K,Ito S,Hata Y

更新日期：1989-12-01 00:00:00

abstract：:The effects of monomer structure on the mechanical properties of visible light-cured composite resins based on the seven types of aromatic dimethacrylates were investigated. The results of this study suggested that the mechanical properties of the composite resins were dependent upon the chemical structure of the dime...

journal_title：Dental materials journal

authors： Kawaguchi M,Fukushima T,Horibe T

更新日期：1989-06-01 00:00:00

abstract：:The aim of the present study was to examine whether interconnected porous hydroxyapatite ceramics (IP-CHA) could be used as bone substitute for implant treatment in reconstructive surgery. We firstly assessed if surround of the titanium surface placed into granular or block-type IP-CHA can observe new bone formation i...

journal_title：Dental materials journal

authors： Minami M,Takechi M,Ohta K,Ohta A,Ninomiya Y,Takamoto M,Fukui A,Tada M,Kamata N

更新日期：2013-01-01 00:00:00

abstract：:The objective of this study is to develop a casting investment that prevents the blackening of the cast surface of noble metal alloys. The experimental investments were prepared using a gypsum-bonded investment in which the metallic powders such as boron (B), silicon (Si), aluminum (Al) and titanium (Ti) were added as...

journal_title：Dental materials journal

authors： Kakuta K,Nakai A,Goto S,Wakamatsu Y,Yara A,Miyagawa Y,Ogura H

更新日期：2003-03-01 00:00:00

abstract：:The aim of this study was to investigate in how far the way the specimen is fixed to the testing device influences the micro-tensile bond strength of adhesives to dentin. Compared to a flat jig, a notched jig enables the specimen to be aligned easier and more accurately perpendicular to the interface, thereby concentr...

journal_title：Dental materials journal

authors： Poitevin A,De Munck J,Van Landuyt K,Coutinho E,Peumans M,Lambrechts P,Van Meerbeek B

更新日期：2007-09-01 00:00:00

abstract：:Effects of functionally gradient calcium phosphate consisting of hydroxyapatite (HAP) and alpha-tricalcium phosphate (alpha-TCP) on proliferation and differentiation of osteoblasts were evaluated using MC3T3-E1 cells. There were no significant differences in the proliferation of MC3T3-E1 cells among HAP-alpha-TCP func...

journal_title：Dental materials journal

authors： Yuasa T,Miyamoto Y,Kon M,Ishikawa K,Takechi M,Momota Y,Tatehara S,Takano H,Mimamiguchi S,Nagayama M

更新日期：2005-06-01 00:00:00

abstract：:Enamel demineralization is one of the most undesired side effects of fixed orthodontic treatment, which will lead to white spot lesions (WSLs) on tooth surfaces. The development of WSLs is due to prolonged accumulation of bacterial plaque and associated acid production. Self-etching adhesives have been used in orthodo...

journal_title：Dental materials journal

authors： Wang X,Zhang N,Wang B,Park SR,Weir MD,Xu HHK,Bai Y

更新日期：2018-07-29 00:00:00

abstract：:The aim of this study was to investigate the diffusion of red-stained experimental GM primer and blue-stained dentin bonding agent into EDTA-conditioned dentin and the effect of GM priming on contraction gap formation. After GM priming at 0, 35, 70, or 100 vol%, marginal adaptation was evaluated by measuring the wall-...

journal_title：Dental materials journal

authors： Nasu Y,Itoh K,Tani C,Hisamitsu H

更新日期：2010-10-01 00:00:00

abstract：:The effects of dissolved-oxygen concentration and fluoride concentration on the corrosion behaviors of commercial pure titanium, Ti-6Al-4V and Ti-6Al-7Nb alloys and experimentally produced Ti-0.2Pd and Ti-0.5Pt alloys were examined using the corrosion potential measurements. The amount of dissolved Ti was analyzed by ...

journal_title：Dental materials journal

authors： Nakagawa M,Matsuya S,Udoh K

更新日期：2002-06-01 00:00:00

abstract：:The aim of the present study was to measure various mechanical properties of acrylic denture base resins, including flexural modulus, flexural strength, fracture toughness, Barcol and Vickers hardness and their related properties, and to investigate correlations between different mechanical properties. Resin specimens...

journal_title：Dental materials journal

authors： Lee HH,Lee CJ,Asaoka K

更新日期：2012-02-03 00:00:00

abstract：:The objective of this work was to determine the antimicrobial and antibiofilm properties of mineral trioxide aggregate (MTA) supplemented with bismuth lipophilic nanoparticles (BisBAL NPs). The antimicrobial activity of the composite MTA-BisBAL NPs was determined by the disk diffusion assay, while antibiofilm activity...

journal_title：Dental materials journal

authors： Hernandez-Delgadillo R,Del Angel-Mosqueda C,Solís-Soto JM,Munguia-Moreno S,Pineda-Aguilar N,Sánchez-Nájera RI,Chellam S,Cabral-Romero C

更新日期：2017-07-26 00:00:00

abstract：:The three-dimensional dynamic movement of the abutment tooth was successfully analyzed on a simulation model utilizing the mandibular kinesiography. When the unilateral free-end denture retained by the RPA, RPI or Aker's clasp was subjected to various directions of loads, the abutment tooth was inclined mainly by the ...

journal_title：Dental materials journal

authors： Morikawa M,Masumi S,Kido H,Toyoda S,Kozono Y

更新日期：1989-06-01 00:00:00

abstract：:The physical properties of experimental visible light-activated resins containing dyestuff, which could be quickly discolored by irradiation was, evaluated by analyzing light absorbance characteristics and measuring micro Vickers hardness. The experimental resin, which was prepared by mixing equivalent weights of Bis ...

journal_title：Dental materials journal

authors： Nakazato J,Itoh K,Wakumoto S

更新日期：1989-12-01 00:00:00

abstract：:The biaxial flexural strength and cyclic fatigue biaxial flexural strength of CAD/CAM ceramics polished with #220, 400, 600 and 1000 diamond pads were measured in an effort to determine the effect of surface roughness on fatigue behavior of dental ceramics. The surface roughness was improved after polishing with a sma...

journal_title：Dental materials journal

authors： Nakazato T,Takahashi H,Yamamoto M,Nishimura F,Kurosaki N

更新日期：1999-12-01 00:00:00

abstract：:The aim of this study was to estimate the flexural properties of three kinds of experimental fiber-reinforced composite (FRC) posts and to evaluate their potential use as posts. Experimental FRC posts were fabricated with glass, aramid, and UHMWP fibers. Commercial FRC posts were used for comparison. A three-point ben...

journal_title：Dental materials journal

authors： Kim MJ,Jung WC,Oh S,Hattori M,Yoshinari M,Kawada E,Oda Y,Bae JM

更新日期：2011-01-01 00:00:00

abstract：:The present study investigated the influences of a denture strengthener on the deformation of a maxillary complete denture. Three groups of maxillary complete dentures were fabricated (Group 1 without a strengthener; Group 2 with a Co-Cr alloy wire strengthener; Group 3 with an experimental fiberglass strengthener). T...

journal_title：Dental materials journal

authors： Hirajima Y,Takahashi H,Minakuchi S

更新日期：2009-07-01 00:00:00

abstract：:The aim of this study was to compare the shear bond strengths (SBS), failure modes (adhesive, cohesive, or mixed), and marginal microleakage occurrence of conventional resin (CR)-based, glass ionomer (GI)-based, and self-adhesive resin (SAR)-based fissure sealants with or without prior phosphoric acid (PA) etching. Fi...

journal_title：Dental materials journal

authors： Simsek Derelioglu S,Yilmaz Y,Celik P,Carikcioglu B,Keles S

更新日期：2014-01-01 00:00:00

abstract：:Major histocompatibility complex (MHC) class II molecule-expressing cells and macrophages play a pivotal role in mediating the host tissue response to biomaterials. This study investigated the responses of these cells to epoxy resin-based and 4-META-containing, methacrylate resin-based endodontic sealers (AH Plus and ...

journal_title：Dental materials journal

authors： Yamanaka Y,Shigetani Y,Yoshiba K,Kaneko T,Yoshiba N,Okiji T

更新日期：2013-01-01 00:00:00

abstract：:A zirconia-binding peptide motif was identified using a peptide phage display system. Yttria stabilized zirconia beads and discs were used as the target. Quartz crystal microbalance was used to monitor the binding of phages to zirconia. Starting from a library of phages displaying random sequences of 12-mer peptides, ...

journal_title：Dental materials journal

authors： Hashimoto K,Yoshinari M,Matsuzaka K,Shiba K,Inoue T

更新日期：2011-01-01 00:00:00

abstract：:This study aimed to introduce a procedure for determining the bilinear elastic moduli (E1 and E2) of the periodontal ligament for a mathematical tooth model to analyse stress in the mandible. The bone and tooth morphology were scanned from a dry skull and an extracted intact tooth, respectively, and reconstructed in a...

journal_title：Dental materials journal

authors： Borák L,Florian Z,Bartáková S,Prachár P,Murakami N,Ona M,Igarashi Y,Wakabayashi N

更新日期：2011-01-01 00:00:00

abstract：:This study tested whether exhaled humid conditions would affect the adhesion of etch-and-rinse, two-step and one-step self-etch adhesive resins to enamel. Enamel surfaces of human maxillary anterior teeth (N=240, n=20) were exposed to four humid conditions (H1: 63-68%, H2: 73-78%, H3: 93-98%, H4: 36-45% RH) during bon...

journal_title：Dental materials journal

authors： Bavbek AB,Demir E,Goktas B,Ozcopur B,Behram B,Eskitascioglu G,Ozcan M

更新日期：2013-01-01 00:00:00

abstract：:The aim of the study was to evaluate bone regeneration using a canine model with surgically created periodontal defects filled for 12 weeks using a stratified biomaterial consisting in a biphasic calcium phosphate (BCP) covered with a crosslinking hydrogel acting as polymer membrane of silated hydroxypropyl methylcell...

journal_title：Dental materials journal

authors： Struillou X,Fruchet A,Rakic M,Badran Z,Rethore G,Sourice S,Fellah BH,LE Guehennec L,Gauthier O,Weiss P,Soueidan A

更新日期：2018-09-30 00:00:00