Bone formation and osseointegration with titanium implant using granular- and block-type porous hydroxyapatite ceramics (IP-CHA).

abstract：:The objective was to compare bond strengths of adhesives with/without thermocycling and to analyze the micromorphology of resindentin interfaces. Flat dentin surfaces were prepared and divided into eight groups to bond with four etch-and-rinse adhesives (Optibond FL, Adper Scotchbond Multi-Purpose, Optibond Solo Plus,...

journal_title：Dental materials journal

authors： Sangwichit K,Kingkaew R,Pongprueksa P,Senawongse P

更新日期：2016-01-01 00:00:00

abstract：:The aim of our study was twofold: to immobilize an organosilicon quaternary ammonium salt (3-(trimethoxysilyl)-propyldimethyl-octadecyl ammonium chloride, Si-QAC) on the surface of pure titanium and to investigate the antimicrobial activity of Si-QAC-immobilized titanium against microbial adherence and biofilm formati...

journal_title：Dental materials journal

authors： Nikawa H,Ishida K,Hamada T,Satoda T,Murayama T,Takemoto T,Tamamoto M,Tajima H,Shimoe S,Fujimoto H,Makihira S

更新日期：2005-12-01 00:00:00

abstract：:The purpose of present investigation was to compare the cyto-genotoxicity induced by five dental alloys in vitro. The cyto-genotoxicity induced by five dental alloy extracts on human B lymphoblast cells was assessed with neutral red uptake (NRU) , CCK-8, comet and micronucleus (CBMN) assays in vitro, respectively. The...

journal_title：Dental materials journal

authors： Zhihong C,Yezhen L,Zhiyuan G,Zhongqiao Y,Xiaoxue L,Yifeng R,Weikun F,Jiliang H

更新日期：2011-01-01 00:00:00

abstract：:This study compared differences in discoloration and dissolution in several titanium alloys with immersion in peroxide- or fluoride-containing solution. Commercially pure titanium (CP-Ti) and six titanium-based alloys were used: Ti-0.15Pd, Ti-6Al-4V, Ti-7Nb-6Al, Ti-55Ni, Ti-10Cu, and Ti-20Cr. Two test solutions were p...

journal_title：Dental materials journal

authors： Noguchi T,Takemoto S,Hattori M,Yoshinari M,Kawada E,Oda Y

更新日期：2008-01-01 00:00:00

abstract：:The purpose of the present study was to analyze effective factors including periodontal ligament on vertical root fractures (VRFs). Eighty maxillary central incisors were assigned to eight groups, depending on master apical file (MAF) size, loading point and existence of a simulated periodontal ligament (PDL). The gut...

journal_title：Dental materials journal

authors： Okitsu M,Takahashi H,Yoshioka T,Iwasaki N,Suda H

更新日期：2005-03-01 00:00:00

abstract：:To determine new developed light curing units with shorter curing times effects on microleakage and microhardness values for resin fissure sealants. Resin filled sealant (UltraSeal-XT), resin unfilled sealant (Delton Type-II) and ormocer-based sealant (Admira-Seal) were light cured with a quartz-tungsten-halogen (QTH)...

journal_title：Dental materials journal

authors： Bani M,Tirali RE

更新日期：2016-01-01 00:00:00

abstract：:Enamel and dentin particles were added to an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step adhesive to react for 30 s. After enamel and dentin reactants were analyzed using X-ray diffraction (XRD) and phosphorus-31 nuclear magnetic resonance ((31)P NMR) techniques, curve-fitting analys...

journal_title：Dental materials journal

authors： Yokota Y,Nishiyama N

更新日期：2015-01-01 00:00:00

abstract：:The torsional fracture strength at the interface between a base plate and veneering material was evaluated for three kinds of veneered restoration: porcelain fused to zirconia (PFZ), porcelain fused to metal (PFM), and composite resin veneered metal (CRVM). The metal and zirconia base plate (30×4×0.4 mm) were prepared...

journal_title：Dental materials journal

authors： Watanabe F,Seto M,Ueda K,Ozawa M

更新日期：2018-07-29 00:00:00

abstract：:The aim of this study was to evaluate the effect of resin infiltration on root caries induced by Streptococcus mutans biofilms. Human premolar specimens were divided to 5 groups: negative control (NC), Clearfil SE Bond (SEB), Icon-etch120s+Icon-infiltrant (HA120), Icon-etch10s+Icon-infiltrant (HA10) and K-etchant10s+I...

journal_title：Dental materials journal

authors： Zhou Y,Matin K,Shimada Y,Sumi Y,Tagami J

更新日期：2017-03-31 00:00:00

abstract：:This study evaluated and compared the influence of different supporting abutment models on the fracture loads of three-unit fixed dental prostheses (FDPs) fabricated from the following materials (n=24/material): (i) IPS e.max CAD-on, (ii) IPS e.max ZirCAD, and (iii) Telio CAD. Twelve FDPs of each group were adhesively...

journal_title：Dental materials journal

authors： Wimmer T,Erdelt KJ,Eichberger M,Roos M,Edelhoff D,Stawarczyk B

更新日期：2014-01-01 00:00:00

abstract：:We investigated the adsorption of lipoteichoic acid (LTA) on titanium surfaces by using the quartz crystal microbalance (QCM) method, and confirmed the influence of mucin (MUC) pre-adsorption on LTA adsorption. Two injection methods were evaluated. Namely, Method A: single-step injection of LTA solution to the Ti sens...

journal_title：Dental materials journal

authors： Yoshida E,Hayakawa T

更新日期：2020-12-03 00:00:00

abstract：:This study examined the ability of a photocatalyst mixed in a denture base resin to decompose organic substances which adhered to the denture base resin surface. The photocatalyst was mixed with denture base resin at concentrations of 0, 5, 10, and 15% (w/w). Decomposition test, bending test, and surface roughness mea...

journal_title：Dental materials journal

authors： Cheng Y,Sakai T,Moroi R,Nakagawa M,Sakai H,Ogata T,Terada Y

更新日期：2008-03-01 00:00:00

abstract：:This study evaluated the effects of combining enamel microabrasion and dental bleaching on the physical properties of enamel, using in vitro and in situ conditions and evaluating surface roughness, enamel microhardness and scanning electron microscopy images. One hundred sound bovine teeth were sectioned and cut into ...

journal_title：Dental materials journal

authors： Franco LM,Machado LS,Salomão FM,Dos Santos PH,Briso AL,Sundfeld RH

更新日期：2016-01-01 00:00:00

abstract：:Oral bacteria adhered to dental material surfaces are known to cause various oral diseases. This study aimed to develop a highsensitive and non-radioisotopic fluorescence dye method for quantification of oral bacteria (Streptococcus, Actinomyces and Veillonella) adhered to denture material surfaces. The amount of adhe...

journal_title：Dental materials journal

authors： Sakuma Y,Washio J,Sasaki K,Takahashi N

更新日期：2013-01-01 00:00:00

abstract：:This paper reviews the development of dental adhesives by collating information of related studies from original scientific papers, reviews, and patent literatures. Through our development, novel radical polymerization initiators, adhesive monomers, and microcapsules were synthesized, and their effects on adhesion wer...

journal_title：Dental materials journal

authors： Ikemura K,Endo T

更新日期：2010-03-01 00:00:00

abstract：:This study aimed to introduce a procedure for determining the bilinear elastic moduli (E1 and E2) of the periodontal ligament for a mathematical tooth model to analyse stress in the mandible. The bone and tooth morphology were scanned from a dry skull and an extracted intact tooth, respectively, and reconstructed in a...

journal_title：Dental materials journal

authors： Borák L,Florian Z,Bartáková S,Prachár P,Murakami N,Ona M,Igarashi Y,Wakabayashi N

更新日期：2011-01-01 00:00:00

abstract：:This study investigated the anti-demineralization effects of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes. Thirty-five bovine root specimens were divided into five treatment groups, with seven specimens each coated with 1) MI varnish (MIV), 2) F varnish (FV), 3) PRG varnish I (PV), 4) PRG varn...

journal_title：Dental materials journal

authors： Shiiya T,Kataoka A,Tomiyama K,Fujino F,Mukai Y

更新日期：2020-11-11 00:00:00

abstract：:The aim of this study was to investigate the diffusion of red-stained experimental GM primer and blue-stained dentin bonding agent into EDTA-conditioned dentin and the effect of GM priming on contraction gap formation. After GM priming at 0, 35, 70, or 100 vol%, marginal adaptation was evaluated by measuring the wall-...

journal_title：Dental materials journal

authors： Nasu Y,Itoh K,Tani C,Hisamitsu H

更新日期：2010-10-01 00:00:00

abstract：:A new tensile fatigue test using a stainless steel screw was introduced. A transparent PMMA rod was selected as the test material. A hole was drilled and tapped into the rod; a screw was put into the rod with dental cement or without cementation. Three types of cyclic loads were applied to the test piece; the number o...

journal_title：Dental materials journal

authors： Nishimura F,Nakamura H,Watari F,Tanaka I,Takahashi H

更新日期：1992-12-01 00:00:00

abstract：:The aim of this study was to determine the effect of autoclave polymerization on the transverse strength of denture base polymers. To this end, 30 rectangular test specimens were fabricated of two heat-polymerized denture base polymers. The test groups were: (I) control, i.e., conventional water bath to polymerize res...

journal_title：Dental materials journal

authors： Durkan R,Ozel MB,Bağiş B,Usanmaz A

更新日期：2008-07-01 00:00:00

abstract：:The aim of this review is to evaluate the long-term effectiveness of calcium silicate-based cement (CS) and calcium hydroxide (CH) for direct pulp capping (DPC) to human pulp-exposed permanent teeth. An electronic search and manual search were performed on 21 June 2019. Long-term clinical and radiographic evaluations ...

journal_title：Dental materials journal

authors： Matsuura T,Ziauddin SM,Kawata-Matsuura VKS,Sugimoto K,Yamada S,Yoshimura A

更新日期：2020-10-01 00:00:00

abstract：:Thermal misfit is deemed as one reason for the chipping of veneered zirconia restorations. Aim of the present study was to assess the effect of thermal misfit on the fracture load of veneered zirconia frameworks and to evaluate the applicability of a universal veneering ceramic for both zirconia and titanium framework...

journal_title：Dental materials journal

authors： Fischer J,Stawarczyk B,Tomic M,Strub JR,Hämmerle CH

更新日期：2007-11-01 00:00:00

abstract：:The effect of warm air-blowing on the sealing ability of two one-bottle and one two-bottle silane-containing universal adhesives (UAs) applied to lithium disilicate ceramics (LDS) was evaluated. Tapered cavities prefabricated in LDS blocks (IPS e.max CAD) were treated by the adhesives, air-blown either with normal air...

journal_title：Dental materials journal

authors： Kaykhine P,Tichy A,Abdou A,Hosaka K,Foxton RM,Sumi Y,Nakajima M,Tagami J

更新日期：2020-10-24 00:00:00

abstract：:The effect of acidic fluoride solution on NiTi arch wires was examined by testing crystal structure, tensile strength, morphology after fracture, and element release from wire under four different test solutions after 1 or 3 d immersion. Three-day immersion in a 0.2%/pH 4 solution did not form any new crystal structur...

journal_title：Dental materials journal

authors： Kwon YH,Cheon YD,Seol HJ,Lee JH,Kim HI

更新日期：2004-12-01 00:00:00

abstract：:The aim of this study was to investigate in how far the way the specimen is fixed to the testing device influences the micro-tensile bond strength of adhesives to dentin. Compared to a flat jig, a notched jig enables the specimen to be aligned easier and more accurately perpendicular to the interface, thereby concentr...

journal_title：Dental materials journal

authors： Poitevin A,De Munck J,Van Landuyt K,Coutinho E,Peumans M,Lambrechts P,Van Meerbeek B

更新日期：2007-09-01 00:00:00

abstract：:The use of a single metal for all restorations would be necessary because it protects against metal corrosion caused by the contact of different metals. For this "one-metal rehabilitation" concept, non-alloyed commercially pure (CP) titanium should be used for all restorations. Titanium frameworks have been cast and u...

journal_title：Dental materials journal

authors： Ohkubo C,Sato Y,Nishiyama Y,Suzuki Y

更新日期：2017-09-26 00:00:00

abstract：:The aim of this study was to evaluate the bond strength of three adhesive systems: Excite™, Adper Prompt L-Pop™ and AdheSE One™ to varying degrees of fluorotic enamel using micro-tensile bond strength (μTBS) tests. Human enamel was classified according to the Thylstrup and Fejerskov Index. The interface resin-enamel w...

journal_title：Dental materials journal

authors： Torres-Gallegos I,A Martinez-Castañon G,Loyola-Rodriguez JP,Patiño-Marin N,Encinas A,Ruiz F,Anusavice K

更新日期：2012-01-01 00:00:00

abstract：:The relation between the bonding efficacy of the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated. The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized 0.5 M EDTA...

journal_title：Dental materials journal

authors： Chiba M,Itoh K,Wakumoto S

更新日期：1989-06-01 00:00:00

abstract：:This study evaluated the effect of resin coating (COA) on dentin bond strength (BS) of five resin cements (RC). Ten groups were tested, according to RC and COA combinations. RCs were applied onto prepolymerized resin discs, which were bonded to dentin surfaces. Teeth were stored in water for 24 h, subjected to 5,000 t...

journal_title：Dental materials journal

authors： Giannini M,Takagaki T,Bacelar-Sá R,Vermelho PM,Ambrosano GM,Sadr A,Nikaido T,Tagami J

更新日期：2015-01-01 00:00:00

abstract：:The purpose of this study was to evaluate the microtensile bond strength (µTBS) of a newly developed resin cement, ECD-89 (ECD, Tokuyama Dental, Tokyo, Japan) to dentin and to observe the interfacial micromorphology by comparing with two commercial resin cements, Multilink Automix (MA, Ivoclar Vivadent AG, Schaan, Lie...

journal_title：Dental materials journal

authors： Kawano S,Fu J,Saikaew P,Chowdhury AA,Fukuzawa N,Kadowaki Y,Kakuda S,Hoshika S,Nakaoki Y,Ikeda T,Tanaka T,Sano H

更新日期：2015-01-01 00:00:00