Effects of fluoride and dissolved oxygen concentrations on the corrosion behavior of pure titanium and titanium alloys.

abstract：:The in vitro dentin permeability of the constituents of two types of conventional phosphoric acid etching agents which had different viscosities, and their pH changes after being permeated dentin were investigated. It was recognized that, even though the etching was for a short time (one minute) followed by rinsing, t...

journal_title：Dental materials journal

authors： Ishikawa K,Ito S,Hata Y

更新日期：1989-12-01 00:00:00

abstract：:Ag-Pd-Cu-Au alloy was subjected to a Thermo-Mechanical Analyzer to investigate high temperature properties up to its liquidus temperature. Microstructural examination and elemental analysis with EPMA were also conducted in the solid/liquid mixture region. The following conclusions were obtained. (1) The solidus temper...

journal_title：Dental materials journal

authors： Nagasawa S,Yoshida T,Mizoguchi T,Terashima N,Ito M,Platt JA,Oshida Y

更新日期：2003-09-01 00:00:00

abstract：:The hardened alpha-case (alpha-case) layer inevitably forms on the surface of titanium castings when prepared by investment casting. Because the hardness of the alpha-case is incomparable to that of the interior structure, the perception exists that the alpha-case is difficult to remove during cutting, grinding and po...

journal_title：Dental materials journal

authors： Koike M,Jacobson D,Chan KS,Okabe T

更新日期：2009-09-01 00:00:00

abstract：:The purpose of this study was to analyze the ultrastructures and chemical compositions of precipitates formed on mineral trioxide aggregate (MTA; White ProRoot MTA) immersed in distilled water (DW) or phosphate buffered saline (PBS), based on the attribution that MTA's bioactivity and sealing ability are influenced by...

journal_title：Dental materials journal

authors： Han L,Okiji T,Okawa S

更新日期：2010-10-01 00:00:00

abstract：:This study investigated the contrast ratio and grain size depending on sintering parameters of twelve different zirconia materials and compared with glass-ceramic (N=156, n=12 per group). Contrast ratio of all ceramics was measured using a spectrophotometer according to ISO 2471: 2008. Grain sizes of zirconia were det...

journal_title：Dental materials journal

authors： Stawarczyk B,Emslander A,Roos M,Sener B,Noack F,Keul C

更新日期：2014-01-01 00:00:00

abstract：:The bonding efficacy of sclerotic dentin was determined by measuring the polymerization contraction gap width of a commercial light-activated resin composite in a cervical defect and by measuring the micro-Vicker's hardness at the dentin adhesive surface; morphological characteristics were observed using a scanning el...

journal_title：Dental materials journal

authors： Tani C,Itoh K,Hisamitsu H,Wakumoto S

更新日期：2001-12-01 00:00:00

abstract：:The purpose of this study was to evaluate the effects of ultrasonic and manual placement techniques on the push-out bond strength of Biodentine and MTA with and without calcium chloride. One hundred and twenty mid-root slices from forty freshly extracted single-rooted human mandibular premolar teeth were instrumented ...

journal_title：Dental materials journal

authors： Küçükkaya Eren S,Aksel H,Serper A

更新日期：2016-10-01 00:00:00

abstract：:The purpose of this study was to evaluate the effects of dentin attrition, phosphoric acid etching, and cyclic loading on the microtensile bond strength (microTBS) of a self-etching adhesive system to dentin. Flat dentin surfaces of human molars were assigned to eight experimental groups based on those with or without...

journal_title：Dental materials journal

authors： Shinkai K,Ebihara T,Shirono M,Seki H,Wakaki S,Suzuki M,Suzuki S,Katoh Y

更新日期：2009-03-01 00:00:00

abstract：:The objective of this work was to analyze the antimicrobial and antibiofilm activities of bismuth lipophilic nanoparticles (BisBAL NPs) incorporated into chitosan-based membranes. Chitosan-based membranes were homogeneously embedded with BisBAL NPs, confirming the bismuth presence by scanning electron microscopy. The ...

journal_title：Dental materials journal

authors： Martínez-Martínez MA,Hernandez-Delgadillo R,Abada BS,Pineda-Aguilar N,Solís-Soto JM,Nakagoshi-Cepeda MAA,Nakagoshi-Cepeda SE,Chellam S,Sánchez-Nájera RI,Cabral-Romero C

更新日期：2019-07-31 00:00:00

abstract：:In this study, different glasses were investigated to improve reusable investments. Borosilicate glass (BSG) powder and soda-lime glass (SLG) powder were prepared by milling broken beakers and microscope slides, respectively, and used in experimental investments (I-BSG, I-SLG) by blending glass powder (10 wt%) with cr...

journal_title：Dental materials journal

authors： Yagi S,Zhang Z,Aida Y,Hotta Y,Tamaki Y,Miyazaki T

更新日期：2011-01-01 00:00:00

abstract：:The purpose of the this study was to evaluate the cytotoxicity of dental resin monomers in the presence of a rat liver S9 mix containing cytochrome P 450 enzymes. JTC-12 cells derived from a monkey kidney were seeded on a 96-well multi-well-plate at 9 x 10(3) cells per well. After cultivation, the S9 mix was added to ...

journal_title：Dental materials journal

authors： Hikage S,Sato A,Suzuki S,Cox CF,Sakaguchi K

更新日期：1999-03-01 00:00:00

abstract：:The extent of polymerization of light-cured composite resins cured in relatively large class II cavities was estimated by measuring Knoop hardness on sectioned surfaces of resin restorations. The influences of the incremental placement technique, exposure time, and post-curing of resin inlay on the extent of polymeriz...

journal_title：Dental materials journal

authors： Hirabayashi S,Hood JA,Hirasawa T

更新日期：1993-12-01 00:00:00

abstract：:Three commercially available porcelains bonded to titanium were evaluated to determine the weakest zone of the titanium-porcelain bonding structures. Tensile bond tests were performed for these specimens (NO, DU, and VI) and for Ni-Cr alloy-porcelain bonding samples that served as controls. The maximum bond strengths ...

journal_title：Dental materials journal

authors： Kannari Y,Endo K,Ida Y,Ochi M,Ohno H

更新日期：2014-01-01 00:00:00

abstract：:The aim of this review is to evaluate the long-term effectiveness of calcium silicate-based cement (CS) and calcium hydroxide (CH) for direct pulp capping (DPC) to human pulp-exposed permanent teeth. An electronic search and manual search were performed on 21 June 2019. Long-term clinical and radiographic evaluations ...

journal_title：Dental materials journal

authors： Matsuura T,Ziauddin SM,Kawata-Matsuura VKS,Sugimoto K,Yamada S,Yoshimura A

更新日期：2020-10-01 00:00:00

abstract：:The human antimicrobial peptide beta-defensin-2 (hBD2) shows broad antibacterial activity and infrequent bacterial resistance. Here mesoporous bioactive glass (MBG) was loaded with hBD2, forming hBD2-loaded MBG (BD-MBG). The antibacterial and osteogenic effects of BD-MBG were investigated in comparison with MBG and th...

journal_title：Dental materials journal

authors： Ren L,Zhang Z,Deng C,Zhang N,Li D

更新日期：2020-12-24 00:00:00

abstract：:Surface replication is a nondestructive evaluation technique applied in examining surfaces' cracks/wear. This is quite valuable when the surface of interest cannot be further manipulated by cutting or polishing to fit directly under a microscope. Replication by acetate sheets is one of the techniques applied in indust...

journal_title：Dental materials journal

authors： Ijbara M,Wada K,Wada J,Jayawardena JA,Miyashin M

更新日期：2019-02-08 00:00:00

abstract：:We evaluated the effect of different curing strategies for universal adhesives on micro-tensile bond strength (μTBS) between resin cement and dentin and/or between resin cement and indirect resin composite. Flat coronal dentin surfaces and composite resin disks were pretreated with silane-containing universal adhesive...

journal_title：Dental materials journal

authors： Araoka D,Hosaka K,Nakajima M,Foxton R,Thanatvarakorn O,Prasansuttiporn T,Chiba A,Sato K,Takahashi M,Otsuki M,Tagami J

更新日期：2018-06-08 00:00:00

abstract：:The effect of acidic fluoride solution on NiTi arch wires was examined by testing crystal structure, tensile strength, morphology after fracture, and element release from wire under four different test solutions after 1 or 3 d immersion. Three-day immersion in a 0.2%/pH 4 solution did not form any new crystal structur...

journal_title：Dental materials journal

authors： Kwon YH,Cheon YD,Seol HJ,Lee JH,Kim HI

更新日期：2004-12-01 00:00:00

abstract：:An experimental primer was developed as a single-step bonding system for resin-modified glass ionomer cements (GIC). Efficacy of this primer on adhesion of resin-modified GICs and resin composite to enamel and dentin was evaluated by shear bond test and SEM observation. Good bond strengths to enamel were obtained (> 1...

journal_title：Dental materials journal

authors： Nikaido T,Nakajima M,Higashi T,Kanemura N,Pereira PN,Tagami J

更新日期：1997-06-01 00:00:00

abstract：:The cream type of denture adhesives after use cannot be easily removed from oral mucosa and have the potential risk to change the oral flora. The effects of the temperature-responsive hydrogel Pluronic F-127 (PF) on the complex viscosity of denture adhesives were evaluated. Carboxy methylcellulose (CMC) mass fractions...

journal_title：Dental materials journal

authors： Zhao H,Akiba N,Tanimoto H,Yoshizaki T,Yalikun K,Minakuchi S

更新日期：2016-01-01 00:00:00

abstract：:The aim of this in vitro study was to evaluate the effects of different preparation angles on the precision of fit of zirconia crown frameworks. Dies were fabricated with three different preparation angles: 4, 8, and 12 degrees total taper. Ten copings were fabricated for each angle by a laboratory and a milling-cente...

journal_title：Dental materials journal

authors： Beuer F,Edelhoff D,Gernet W,Naumann M

更新日期：2008-11-01 00:00:00

abstract：:The purpose of the present study was to evaluate the effect of four silane coupling agents on the bond strength between two resin-modified glass ionomer cements and a machinable leucite glass ceramic. Ceramic specimens were ground with silicon carbide paper and cleaned with phosphoric acid. They were then conditioned ...

journal_title：Dental materials journal

authors： Kamada K,Taira Y,Yoshida K,Atsuta M

更新日期：2007-03-01 00:00:00

abstract：:To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding gro...

journal_title：Dental materials journal

authors： Kusunoki M,Itoh K,Takahashi Y,Hisamitsu H

更新日期：2006-09-01 00:00:00

abstract：:The aim of this study was to investigate the effects of potassium fluoride (KF) and sodium fluoride (NaF) in different concentrations on micro-shear bond strength (µSBS) and their protective effects against acid. The enamel blocks were treated with several concentrations of KF and NaF. For µSBS, Clearfil SE Bond 2 was...

journal_title：Dental materials journal

authors： Al-Qahtani A,Inoue G,Abdou A,Nikaido T,Tagami J

更新日期：2020-10-27 00:00:00

abstract：:This study evaluated and compared the influence of different supporting abutment models on the fracture loads of three-unit fixed dental prostheses (FDPs) fabricated from the following materials (n=24/material): (i) IPS e.max CAD-on, (ii) IPS e.max ZirCAD, and (iii) Telio CAD. Twelve FDPs of each group were adhesively...

journal_title：Dental materials journal

authors： Wimmer T,Erdelt KJ,Eichberger M,Roos M,Edelhoff D,Stawarczyk B

更新日期：2014-01-01 00:00:00

abstract：:The objective of this study was to clarify the effect of surface topography on osteoblast-like cell behavior on yttria stabilized tetragonal zirconia polycrystals (TZP). Mirror-polished; blasted with 50- or 150-µm alumina (SB50 and SB150); and SB150 acid-etched with hydrofluoric acid (SB150E) were prepared on TZP. Ini...

journal_title：Dental materials journal

authors： Ito H,Sasaki H,Saito K,Honma S,Yajima Y,Yoshinari M

更新日期：2013-01-01 00:00:00

abstract：:This study examined the effect of air abrasion and thermocycling on the adaptation and shear bond strength, of composite resin bonded to dentin using etch-and-rinse and self-etch resin adhesives. Confocal microscopy showed both adhesives closely adapted to dentin and a significantly (p<0.001) greater number of resin t...

journal_title：Dental materials journal

authors： Freeman R,Varanasi S,Meyers IA,Symons AL

更新日期：2012-01-01 00:00:00

abstract：:We investigated the adsorption of lipoteichoic acid (LTA) on titanium surfaces by using the quartz crystal microbalance (QCM) method, and confirmed the influence of mucin (MUC) pre-adsorption on LTA adsorption. Two injection methods were evaluated. Namely, Method A: single-step injection of LTA solution to the Ti sens...

journal_title：Dental materials journal

authors： Yoshida E,Hayakawa T

更新日期：2020-12-03 00:00:00

abstract：:The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...

journal_title：Dental materials journal

authors： Doi K,Kubo T,Hayashi K,Imura K,Akagawa Y

更新日期：2007-03-01 00:00:00

abstract：:With a view to understanding the structure-property relation of a silicone-based soft lining denture material after polymerization, its chemical composition and viscoelastic properties were investigated. Chemical compositions of the cured and uncured polymers of a commercial silicone permanent soft liner were determin...

journal_title：Dental materials journal

authors： Doğan OM,Keskin S,Doğan A,Ataman H,Usanmaz A

更新日期：2007-05-01 00:00:00