Morphological and chemical analysis of different precipitates on mineral trioxide aggregate immersed in different fluids.

abstract：:The purpose of this study was to evaluate the effect of various incremental filling techniques on adhesion between composite and cavity floor using light-cured resin composite. Black ABS resin and hybrid resin composite were used as mold materials--instead of dentin--for the preparation of cavities, and standardized t...

journal_title：Dental materials journal

authors： Chikawa H,Inai N,Cho E,Kishikawa R,Otsuki M,Foxton RM,Tagami J

更新日期：2006-09-01 00:00:00

abstract：:An experimental primer was developed as a single-step bonding system for resin-modified glass ionomer cements (GIC). Efficacy of this primer on adhesion of resin-modified GICs and resin composite to enamel and dentin was evaluated by shear bond test and SEM observation. Good bond strengths to enamel were obtained (> 1...

journal_title：Dental materials journal

authors： Nikaido T,Nakajima M,Higashi T,Kanemura N,Pereira PN,Tagami J

更新日期：1997-06-01 00:00:00

abstract：:The aim of this in vitro study was to evaluate the effects of different preparation angles on the precision of fit of zirconia crown frameworks. Dies were fabricated with three different preparation angles: 4, 8, and 12 degrees total taper. Ten copings were fabricated for each angle by a laboratory and a milling-cente...

journal_title：Dental materials journal

authors： Beuer F,Edelhoff D,Gernet W,Naumann M

更新日期：2008-11-01 00:00:00

abstract：:The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...

journal_title：Dental materials journal

authors： Watanabe K,Okawa S,Kanatani M,Nakano S,Miyakawa O,Kobayashi M

更新日期：1996-12-01 00:00:00

abstract：:This study examined the effect of air abrasion and thermocycling on the adaptation and shear bond strength, of composite resin bonded to dentin using etch-and-rinse and self-etch resin adhesives. Confocal microscopy showed both adhesives closely adapted to dentin and a significantly (p<0.001) greater number of resin t...

journal_title：Dental materials journal

authors： Freeman R,Varanasi S,Meyers IA,Symons AL

更新日期：2012-01-01 00:00:00

abstract：:The purpose of this study was to evaluate the microtensile bond strength (µTBS) of a newly developed resin cement, ECD-89 (ECD, Tokuyama Dental, Tokyo, Japan) to dentin and to observe the interfacial micromorphology by comparing with two commercial resin cements, Multilink Automix (MA, Ivoclar Vivadent AG, Schaan, Lie...

journal_title：Dental materials journal

authors： Kawano S,Fu J,Saikaew P,Chowdhury AA,Fukuzawa N,Kadowaki Y,Kakuda S,Hoshika S,Nakaoki Y,Ikeda T,Tanaka T,Sano H

更新日期：2015-01-01 00:00:00

abstract：:This in vitro study aimed to investigate the effects of glass-ionomer and flowable composite liners on the fracture resistance of Class II amalgam and composite restorations. Group 1 cavities were restored with amalgam and Group 4 cavities with nanofill composite after the application of a dentin-bonding agent. For th...

journal_title：Dental materials journal

authors： Güray Efes B,Yaman BC,Gümüştaş B,Tıryakı M

更新日期：2013-01-01 00:00:00

abstract：:Thermal misfit is deemed as one reason for the chipping of veneered zirconia restorations. Aim of the present study was to assess the effect of thermal misfit on the fracture load of veneered zirconia frameworks and to evaluate the applicability of a universal veneering ceramic for both zirconia and titanium framework...

journal_title：Dental materials journal

authors： Fischer J,Stawarczyk B,Tomic M,Strub JR,Hämmerle CH

更新日期：2007-11-01 00:00:00

abstract：:This study aimed to investigate the in vitro biological response of human dental pulp cells to glass ionomer cement (GIC, Fuji IX GP(®)) containing 2.5% magnesium carbonate apatite (MgCO(3)Ap). MgCO(3)Ap was synthesized by wet method and characterized using FT-IR, XPS, and SEM. Fuji IX GP(®) served as a control. Test ...

journal_title：Dental materials journal

authors： Laiteerapong A,Lochaiwatana Y,Hirata I,Okazaki M,Mori K,Murakami S,Poolthong S

更新日期：2012-01-01 00:00:00

abstract：:This study assessed the impact of surface treatments and repair resin reinforcement with zirconium oxide nano-particles (nano-ZrO2) on flexural strength (FS) of repaired denture base. A total of 320 heat-polymerized acrylic resin specimens were prepared and sectioned creating 2-mm gap. According to repair surface trea...

journal_title：Dental materials journal

authors： Gad MM,Rahoma A,Abualsaud R,Al-Thobity AM,Akhtar S,Helal MA,Al-Harbi FA

更新日期：2020-06-05 00:00:00

abstract：:The objective was to compare bond strengths of adhesives with/without thermocycling and to analyze the micromorphology of resindentin interfaces. Flat dentin surfaces were prepared and divided into eight groups to bond with four etch-and-rinse adhesives (Optibond FL, Adper Scotchbond Multi-Purpose, Optibond Solo Plus,...

journal_title：Dental materials journal

authors： Sangwichit K,Kingkaew R,Pongprueksa P,Senawongse P

更新日期：2016-01-01 00:00:00

abstract：:This study evaluated the effects of combining enamel microabrasion and dental bleaching on the physical properties of enamel, using in vitro and in situ conditions and evaluating surface roughness, enamel microhardness and scanning electron microscopy images. One hundred sound bovine teeth were sectioned and cut into ...

journal_title：Dental materials journal

authors： Franco LM,Machado LS,Salomão FM,Dos Santos PH,Briso AL,Sundfeld RH

更新日期：2016-01-01 00:00:00

abstract：:To recognize good mechanical properties and water-resistance of a dental resin, dimethacryloxyethyl-1,1,6,6-tetrahydro-perfluoro-hexamethylene-1,6-dicarbamate (FDMHD) was newly synthesized. FDMHD initially was a white powder with m.p. 98.5-99.5°C. The copolymers of FDMHD and methyl methacrylate (MMA), FDMHD/MMA copoly...

journal_title：Dental materials journal

authors： Kurata S,Yamazaki N

更新日期：2011-01-01 00:00:00

abstract：:This study evaluated the biomineralization and dentinal tubules occlusion abilities of the carboxyl-terminated polyamidoamine dendrimer (PAMAM-COOH) on human demineralized dentin in vivo at different time points. Demineralization dentin model with and without treated with PAMAM-COOH were sutured to the interior side o...

journal_title：Dental materials journal

authors： Xie F,Wei X,Li Q,Zhou T

更新日期：2016-01-01 00:00:00

abstract：:Present study evaluated effects of addition of Nanoparticles fluorapatite (Nano-FA) on microhardness and fluoride release of a Glass Ionomer Cement (GIC, Fuji IX GP Fast). Forty-eight specimens prepared, divided equally into 4 groups (2 with Nano-FA); after 24 h and one week Vickers microhardness (HV) was measured. Na...

journal_title：Dental materials journal

authors： Moshaverinia M,Borzabadi-Farahani A,Sameni A,Moshaverinia A,Ansari S

更新日期：2016-01-01 00:00:00

abstract：:The purpose of the present study was to evaluate the effect of four silane coupling agents on the bond strength between two resin-modified glass ionomer cements and a machinable leucite glass ceramic. Ceramic specimens were ground with silicon carbide paper and cleaned with phosphoric acid. They were then conditioned ...

journal_title：Dental materials journal

authors： Kamada K,Taira Y,Yoshida K,Atsuta M

更新日期：2007-03-01 00:00:00

abstract：:The biaxial flexural strength and cyclic fatigue biaxial flexural strength of CAD/CAM ceramics polished with #220, 400, 600 and 1000 diamond pads were measured in an effort to determine the effect of surface roughness on fatigue behavior of dental ceramics. The surface roughness was improved after polishing with a sma...

journal_title：Dental materials journal

authors： Nakazato T,Takahashi H,Yamamoto M,Nishimura F,Kurosaki N

更新日期：1999-12-01 00:00:00

abstract：:This study compared bovine serum albumin (BSA) adsorption onto octacalcium phosphate (OCP) materials prepared from two wet preparations in the absence (w-OCP) and presence (c-OCP) of gelatin. Raman spectroscopy was used to analyze the BSA adsorption onto OCPs in a 150 mM Tris-HCl buffer containing 0.5 mM calcium and i...

journal_title：Dental materials journal

authors： Tsuchiya K,Hamai R,Sakai S,Suzuki O

更新日期：2020-09-29 00:00:00

abstract：:The aim of this study was to evaluate the trial Teaching Robot for the development of a contact-type measuring apparatus for using directly in the oral cavity. A standard model was used to mimic the dentition by placing an arrangement of three bearing balls. The diameters of the balls were measured. A practical dentit...

journal_title：Dental materials journal

authors： Maikuma Y,Usui K,Araki K,Mataki S,Kurosaki N,Furuya N

更新日期：2003-06-01 00:00:00

abstract：:The diamond burs of two dental CAD/CAM systems (GN and CD) were examined if they could be used to fabricate up to 21 ceramic full crowns without fracture. After one, 11, and 21 machining times, the surfaces of the diamond burs were observed and the number of particles captured on SEM pictures was counted. The average ...

journal_title：Dental materials journal

authors： Yara A,Ogura H,Shinya A,Tomita S,Miyazaki T,Sugai Y,Sakamoto Y

更新日期：2005-03-01 00:00:00

abstract：:This study compared differences in discoloration and dissolution in several titanium alloys with immersion in peroxide- or fluoride-containing solution. Commercially pure titanium (CP-Ti) and six titanium-based alloys were used: Ti-0.15Pd, Ti-6Al-4V, Ti-7Nb-6Al, Ti-55Ni, Ti-10Cu, and Ti-20Cr. Two test solutions were p...

journal_title：Dental materials journal

authors： Noguchi T,Takemoto S,Hattori M,Yoshinari M,Kawada E,Oda Y

更新日期：2008-01-01 00:00:00

abstract：:The purpose of this study was to clarify the effect of silver nanoparticles on the behavior of subcritical crack growth (SCG) in dental porcelains. Prior to occurrence of fast fracture in dental porcelains, SCG occurs and leads to strength degradation over time. SCG in dental porcelains can be characterized by the str...

journal_title：Dental materials journal

authors： Fujieda T,Uno M,Ishigami H,Kurachi M,Kamemizu H,Wakamatsu N,Doi Y

更新日期：2013-01-01 00:00:00

abstract：:The clinical feasibility of a novel device called a Cariotester was investigated by measuring the Knoop hardness (KHN) of white spot lesions diagnosed as ICDAS code 1, 2 or 3. To obtain an equation for converting the Cariotester indentation depth into the KHN, a regression analysis was performed between the depth and ...

journal_title：Dental materials journal

authors： Shimizu A,Yamamoto T,Nakashima S,Nikaido T,Sugawara T,Momoi Y

更新日期：2015-01-01 00:00:00

abstract：:We evaluated the effect of different curing strategies for universal adhesives on micro-tensile bond strength (μTBS) between resin cement and dentin and/or between resin cement and indirect resin composite. Flat coronal dentin surfaces and composite resin disks were pretreated with silane-containing universal adhesive...

journal_title：Dental materials journal

authors： Araoka D,Hosaka K,Nakajima M,Foxton R,Thanatvarakorn O,Prasansuttiporn T,Chiba A,Sato K,Takahashi M,Otsuki M,Tagami J

更新日期：2018-06-08 00:00:00

abstract：:This study evaluated a new enzyme solution (SFC-V) for dentin caries removal, and obtained results were compared with Carisolv. Both solutions were used with a prototype plastic instrument - this being a modified technique for Carisolv. Five carious deciduous teeth were sectioned, and both treatments were applied alte...

journal_title：Dental materials journal

authors： Clementino-Luedemann TN,Dabanoglu A,Ilie N,Hickel R,Kunzelmann KH

更新日期：2006-12-01 00:00:00

abstract：:Novel fast-setting calcium silicate cement with fluoride (CSC) has been developed for potential applications in tooth crown. The aim of this study was to test the diametral tensile strength (DTS) of different CSC compositions in humid condition on day1, 28, and 180. We tested 'bond CSC' with 3.5% fluoride and no radio...

journal_title：Dental materials journal

authors： Ranjkesh B,Isidor F,Dalstra M,Løvschall H

更新日期：2016-01-01 00:00:00

abstract：:The aim of this study was to evaluate the effect of resin infiltration on root caries induced by Streptococcus mutans biofilms. Human premolar specimens were divided to 5 groups: negative control (NC), Clearfil SE Bond (SEB), Icon-etch120s+Icon-infiltrant (HA120), Icon-etch10s+Icon-infiltrant (HA10) and K-etchant10s+I...

journal_title：Dental materials journal

authors： Zhou Y,Matin K,Shimada Y,Sumi Y,Tagami J

更新日期：2017-03-31 00:00:00

abstract：:The objective of this study was to evaluate, using methylene blue (MB), the effects of various light sources on the bleaching action of hydrogen peroxide (H(2)O(2)) with two titanium dioxide (TiO(2)) photocatalysts - an ultraviolet light-activated TiO(2) photocatalyst (UVTiO(2)) versus a visible light-activated TiO(2)...

journal_title：Dental materials journal

authors： Suyama Y,Otsuki M,Ogisu S,Kishikawa R,Tagami J,Ikeda M,Kurata H,Cho T

更新日期：2009-11-01 00:00:00

abstract：:This study evaluated the effect of different adhesive protocols on the shear bond strength (SBS) of bulk-fill resin composite repaired with bulk-fill or conventional composite. Cylindrical bulk-fill resin composite specimens were prepared and allocated into groups according to the bonding strategy: no treatment, Silan...

journal_title：Dental materials journal

authors： Cuevas-Suárez CE,Nakanishi L,Isolan CP,Ribeiro JS,Moreira AG,Piva E

更新日期：2020-03-31 00:00:00

abstract：:The three-dimensional dynamic movement of the abutment tooth was successfully analyzed on a simulation model utilizing the mandibular kinesiography. When the unilateral free-end denture retained by the RPA, RPI or Aker's clasp was subjected to various directions of loads, the abutment tooth was inclined mainly by the ...

journal_title：Dental materials journal

authors： Morikawa M,Masumi S,Kido H,Toyoda S,Kozono Y

更新日期：1989-06-01 00:00:00