Effect of four silane coupling agents on bonding of two resin-modified glass ionomer cements to a machinable ceramic.

Abstract:

:The purpose of the present study was to evaluate the effect of four silane coupling agents on the bond strength between two resin-modified glass ionomer cements and a machinable leucite glass ceramic. Ceramic specimens were ground with silicon carbide paper and cleaned with phosphoric acid. They were then conditioned and bonded with combinations of four silane coupling agents (GC Ceramic Primer, Clapearl Bonding Agent, Clearfil Mega Bond Porcelain Bonding Kit, and RelyX Ceramic Primer) and two resin-modified glass ionomer cements (Fuji Luting S and Fuji Lute). Shear bond strength was determined after 24-hour immersion in water or after thermocycling of 50,000 cycles. The results showed that every silane coupling agent significantly improved the bond strength. It was thus recommended that resin-modified glass ionomer cement be applied in conjunction with silane coupling agent when luting ceramic restorations.

journal_name

Dent Mater J

journal_title

Dental materials journal

authors

Kamada K,Taira Y,Yoshida K,Atsuta M

doi

10.4012/dmj.26.240

subject

Has Abstract

pub_date

2007-03-01 00:00:00

pages

240-4

issue

2

eissn

0287-4547

issn

1881-1361

journal_volume

26

pub_type

杂志文章
  • Effect of experimental acid/base conditioner on microtensile bond strength of 4-META/MMA-TBB resin to dentin after long-term water immersion.

    abstract::An experimental conditioner (Exp), which was an aqueous solution of 10% ascorbic acid and 5% ferric chloride, was prepared in this study. This study evaluated the effect of Exp on the microtensile bond strength between a self-curing resin and dentin after long-term water immersion. Flat human dentin surfaces were sequ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2012-078

    authors: Soeno K,Taira Y,Ito S

    更新日期:2012-01-01 00:00:00

  • Technique-sensitivity of contemporary adhesives.

    abstract::Besides micro-mechanical interlocking through hybrid-layer formation, self-etch adhesives may benefit from additional chemical interaction between the functional monomer and residual hydroxyapatite. One-step adhesives are commonly associated with lower bonding effectiveness, which must be attributed in part to the dis...

    journal_title:Dental materials journal

    pub_type: 杂志文章,评审

    doi:10.4012/dmj.24.1

    authors: Van Meerbeek B,Van Landuyt K,De Munck J,Hashimoto M,Peumans M,Lambrechts P,Yoshida Y,Inoue S,Suzuki K

    更新日期:2005-03-01 00:00:00

  • Effects of attrition, prior acid-etching, and cyclic loading on the bond strength of a self-etching adhesive system to dentin.

    abstract::The purpose of this study was to evaluate the effects of dentin attrition, phosphoric acid etching, and cyclic loading on the microtensile bond strength (microTBS) of a self-etching adhesive system to dentin. Flat dentin surfaces of human molars were assigned to eight experimental groups based on those with or without...

    journal_title:Dental materials journal

    pub_type: 杂志文章,随机对照试验

    doi:10.4012/dmj.28.197

    authors: Shinkai K,Ebihara T,Shirono M,Seki H,Wakaki S,Suzuki M,Suzuki S,Katoh Y

    更新日期:2009-03-01 00:00:00

  • Reinforcement mechanism of dentin mechanical properties by intracanal medicaments.

    abstract::The reinforcement mechanism of dentin mechanical properties by intracanal medicaments was investigated. The dumbbell-shaped specimens were prepared from a collagen sheet, demineralized dentin and organic dissolved dentin. After immersing the specimens in intracanal medicaments (eugenol and formocresol), the tensile te...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.18.304

    authors: Nakano F,Takahashi H,Nishimura F

    更新日期:1999-09-01 00:00:00

  • Predicting in vivo failure of rotary nickel-titanium endodontic instruments under cyclic fatigue.

    abstract::The aim of this study was to examine the lifespan or number of cycles to failure of tapered rotary nickel-titanium (Ni-Ti) endodontic instruments. Simulated root canals with different curvatures were used to determine a relation between canal curvature and instrument lifespan. Using a novel mathematical model for the ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2011-254

    authors: Stojanac I,Drobac M,Petrovic L,Atanackovic T

    更新日期:2012-01-01 00:00:00

  • Diffusion of GM primer and dentin adhesive into EDTA-conditioned dentin.

    abstract::The aim of this study was to investigate the diffusion of red-stained experimental GM primer and blue-stained dentin bonding agent into EDTA-conditioned dentin and the effect of GM priming on contraction gap formation. After GM priming at 0, 35, 70, or 100 vol%, marginal adaptation was evaluated by measuring the wall-...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2009-084

    authors: Nasu Y,Itoh K,Tani C,Hisamitsu H

    更新日期:2010-10-01 00:00:00

  • Contraction gap versus shear bond strength of dentin adhesive in sound and sclerotic dentins.

    abstract::To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding gro...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.25.576

    authors: Kusunoki M,Itoh K,Takahashi Y,Hisamitsu H

    更新日期:2006-09-01 00:00:00

  • Chemical mechanical polishing of titanium with colloidal silica containing hydrogen peroxide--mirror polishing and surface properties.

    abstract::Chemical mechanical polishing (CMP) of cpTi (Ti) was carried out using two types of slurries, acidic and basic colloidal silica containing H2O2 up to 3 wt%, to obtain flat and mirror-polished surfaces without any contaminated and reacted layers. Polishing behavior and surface properties were investigated using AFM, EP...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.28.68

    authors: Okawa S,Watanabe K

    更新日期:2009-01-01 00:00:00

  • Determination of molecular species of calcium salts of MDP produced through decalcification of enamel and dentin by MDP-based one-step adhesive.

    abstract::Enamel and dentin particles were added to an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step adhesive to react for 30 s. After enamel and dentin reactants were analyzed using X-ray diffraction (XRD) and phosphorus-31 nuclear magnetic resonance ((31)P NMR) techniques, curve-fitting analys...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2014-260

    authors: Yokota Y,Nishiyama N

    更新日期:2015-01-01 00:00:00

  • Effect of adhesive primer developed exclusively for heat-curing resin on adhesive strength between plastic artificial tooth and acrylic denture base resin.

    abstract::Despite progress in the development of denture base resin and artificial tooth materials, dental clinics are still plagued with artificial teeth falling off the denture base--due to poor bond strength--after denture delivery. Against this background, this study sought to examine the effect and durability of an adhesiv...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.25.75

    authors: Nishigawa G,Maruo Y,Okamoto M,Oki K,Kinuta Y,Minagi S,Irie M,Suzuki K

    更新日期:2006-03-01 00:00:00

  • Structure-property relation of a soft liner material used in denture applications.

    abstract::With a view to understanding the structure-property relation of a silicone-based soft lining denture material after polymerization, its chemical composition and viscoelastic properties were investigated. Chemical compositions of the cured and uncured polymers of a commercial silicone permanent soft liner were determin...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:

    authors: Doğan OM,Keskin S,Doğan A,Ataman H,Usanmaz A

    更新日期:2007-05-01 00:00:00

  • In vitro pH analysis of active and arrested dentinal caries in extracted human teeth using a micro pH sensor.

    abstract::The aim of this study was to evaluate the pH at the surface of active or arrested carious dentin using a micro pH sensor, and to compare the relationship between different pH measurement techniques. Twenty extracted carious teeth were divided into two groups, active or arrested caries, according to predefined clinical...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.25.423

    authors: Murakami K,Kitasako Y,Burrow MF,Tagami J

    更新日期:2006-09-01 00:00:00

  • Impact of different surface treatments and repair material reinforcement on the flexural strength of repaired PMMA denture base material.

    abstract::This study assessed the impact of surface treatments and repair resin reinforcement with zirconium oxide nano-particles (nano-ZrO2) on flexural strength (FS) of repaired denture base. A total of 320 heat-polymerized acrylic resin specimens were prepared and sectioned creating 2-mm gap. According to repair surface trea...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-436

    authors: Gad MM,Rahoma A,Abualsaud R,Al-Thobity AM,Akhtar S,Helal MA,Al-Harbi FA

    更新日期:2020-06-05 00:00:00

  • Bone formation and osseointegration with titanium implant using granular- and block-type porous hydroxyapatite ceramics (IP-CHA).

    abstract::The aim of the present study was to examine whether interconnected porous hydroxyapatite ceramics (IP-CHA) could be used as bone substitute for implant treatment in reconstructive surgery. We firstly assessed if surround of the titanium surface placed into granular or block-type IP-CHA can observe new bone formation i...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2012-169

    authors: Minami M,Takechi M,Ohta K,Ohta A,Ninomiya Y,Takamoto M,Fukui A,Tada M,Kamata N

    更新日期:2013-01-01 00:00:00

  • An ultrastructural analysis of the prototype single-step adhesive applied on enamel and dentin surfaces.

    abstract::A new type of self-etching agent, the single-step adhesive, was developed. The purpose of this study was to investigate the difference in the ultrastructural features of enamel and dentin surfaces following application of the prototype single-step adhesive (EXM618, 3M, MN, USA). Extracted caries-free human premolars w...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.23.321

    authors: Han L,Cruz E,Fukushima M,Okamoto A,Okiji T

    更新日期:2004-09-01 00:00:00

  • Effects of degree of dissociation of acid used on hydrolytic durability of ceramic primer.

    abstract::In this study, effects of the degree of dissociation of acids on the hydrolysis rate of methoxy group in γ-methacryloxypropyltrimethoxysilane (γ-MPS) and the adsorption characteristics of γ-MPS on ceramic surfaces were studied using acetic, phosphoric, and hydrochloric acids. Hydrolytic stability of γ-MPS adsorption l...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2013-319

    authors: Aoki N,Kimoto S,Tanimura H,Nishiyama N,Aida M

    更新日期:2014-01-01 00:00:00

  • Antimicrobial potential of bismuth lipophilic nanoparticles embedded into chitosan-based membrane.

    abstract::The objective of this work was to analyze the antimicrobial and antibiofilm activities of bismuth lipophilic nanoparticles (BisBAL NPs) incorporated into chitosan-based membranes. Chitosan-based membranes were homogeneously embedded with BisBAL NPs, confirming the bismuth presence by scanning electron microscopy. The ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2018-173

    authors: Martínez-Martínez MA,Hernandez-Delgadillo R,Abada BS,Pineda-Aguilar N,Solís-Soto JM,Nakagoshi-Cepeda MAA,Nakagoshi-Cepeda SE,Chellam S,Sánchez-Nájera RI,Cabral-Romero C

    更新日期:2019-07-31 00:00:00

  • Effect of sodium hypochlorite contamination on microhardness of dental core build-up materials.

    abstract::This study aimed to determine the influence of sodium hypochlorite (NaOCl) contamination on the microhardness of build-up composites. Fifty-two samples, from each of three build-up materials (LuxaCore Dual, MultiCore flow and Rebilda DC) were prepared. Half of the samples from each material were stored in physiologic ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2010-007

    authors: Wegehaupt FJ,Betschart J,Attin T

    更新日期:2010-08-01 00:00:00

  • Surface damages of zirconia by Nd:YAG dental laser irradiation.

    abstract::The purpose of this study was to characterize the surface damages of zirconia by Nd:YAG dental laser irradiation through a systematic evaluation of the associated microstructural changes. Disk specimens of yttria-stabilized tetragonal zirconia polycrystals (Y-TZP) and ceria-stabilized zirconia/alumina nanocomposite (C...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2009-127

    authors: Noda M,Okuda Y,Tsuruki J,Minesaki Y,Takenouchi Y,Ban S

    更新日期:2010-10-01 00:00:00

  • Bilinear elastic property of the periodontal ligament for simulation using a finite element mandible model.

    abstract::This study aimed to introduce a procedure for determining the bilinear elastic moduli (E1 and E2) of the periodontal ligament for a mathematical tooth model to analyse stress in the mandible. The bone and tooth morphology were scanned from a dry skull and an extracted intact tooth, respectively, and reconstructed in a...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2010-170

    authors: Borák L,Florian Z,Bartáková S,Prachár P,Murakami N,Ona M,Igarashi Y,Wakabayashi N

    更新日期:2011-01-01 00:00:00

  • Possible segregation caused by centrifugal titanium casting.

    abstract::The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.15.212

    authors: Watanabe K,Okawa S,Kanatani M,Nakano S,Miyakawa O,Kobayashi M

    更新日期:1996-12-01 00:00:00

  • Effect of monomer structure on the mechanical properties of light-cured composite resins.

    abstract::The effects of monomer structure on the mechanical properties of visible light-cured composite resins based on the seven types of aromatic dimethacrylates were investigated. The results of this study suggested that the mechanical properties of the composite resins were dependent upon the chemical structure of the dime...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.8.40

    authors: Kawaguchi M,Fukushima T,Horibe T

    更新日期:1989-06-01 00:00:00

  • Effects of potassium and sodium fluoride in different concentrations on micro-shear bond strength and inhibition of demineralization.

    abstract::The aim of this study was to investigate the effects of potassium fluoride (KF) and sodium fluoride (NaF) in different concentrations on micro-shear bond strength (µSBS) and their protective effects against acid. The enamel blocks were treated with several concentrations of KF and NaF. For µSBS, Clearfil SE Bond 2 was...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2020-019

    authors: Al-Qahtani A,Inoue G,Abdou A,Nikaido T,Tagami J

    更新日期:2020-10-27 00:00:00

  • Fabrication of all-ceramic crowns by a new method.

    abstract::A new method of all-ceramic production using alumina coping has been developed. The present study investigates the influence of secondary firing (glass infiltration firing) conditions. Samples of porcelain build-up without secondary firing were also assessed. The suitability of coping that included secondary firing wa...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-275

    authors: Masuda T,Kakimoto K,Takahashi K,Komasa Y

    更新日期:2016-01-01 00:00:00

  • Influence of resin coating on bond strength of self-adhesive resin cements to dentin.

    abstract::This study evaluated the effect of resin coating (COA) on dentin bond strength (BS) of five resin cements (RC). Ten groups were tested, according to RC and COA combinations. RCs were applied onto prepolymerized resin discs, which were bonded to dentin surfaces. Teeth were stored in water for 24 h, subjected to 5,000 t...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-099

    authors: Giannini M,Takagaki T,Bacelar-Sá R,Vermelho PM,Ambrosano GM,Sadr A,Nikaido T,Tagami J

    更新日期:2015-01-01 00:00:00

  • Comparative analysis of bovine serum albumin adsorption onto octacalcium phosphate crystals prepared using different methods.

    abstract::This study compared bovine serum albumin (BSA) adsorption onto octacalcium phosphate (OCP) materials prepared from two wet preparations in the absence (w-OCP) and presence (c-OCP) of gelatin. Raman spectroscopy was used to analyze the BSA adsorption onto OCPs in a 150 mM Tris-HCl buffer containing 0.5 mM calcium and i...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-250

    authors: Tsuchiya K,Hamai R,Sakai S,Suzuki O

    更新日期:2020-09-29 00:00:00

  • Effect of light intensity on polymerization of light-cured composite resins.

    abstract::The depths of cure and the distributions of degree of conversion (DC), polymerization conversion (PC) and percent pendant double bonds (PDB) of light-cured composite resins cured under various intensities of light were investigated. When the total amount of exposure, represented by the product of the light intensity a...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.13.198

    authors: Nomoto R,Uchida K,Hirasawa T

    更新日期:1994-12-01 00:00:00

  • Water durability of resin bond to pure gold treated with various adhesion promoting thiirane monomers.

    abstract::Adhesion promoting monomers for precious metals, 2,3-epithiopropyl methacrylate (EP1MA), 4,5-epithiopentyl methacrylate (EP3MA), 9,10-epithiodecyl methacrylate (EP8MA), 10,11-epithioundecyl methacrylate (EP9MA), 9,10-epithiodecyl 4-vinylbenzoate (EP8VB), 2,3-epithiocyclohexyl methacrylate (EPCHMA), and 3,4-epithiobuty...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.26.29

    authors: Kadoma Y,Kojima K,Tamaki Y,Nomura Y

    更新日期:2007-01-01 00:00:00

  • Effects of temperature-responsive hydrogel on viscosity of denture adhesives.

    abstract::The cream type of denture adhesives after use cannot be easily removed from oral mucosa and have the potential risk to change the oral flora. The effects of the temperature-responsive hydrogel Pluronic F-127 (PF) on the complex viscosity of denture adhesives were evaluated. Carboxy methylcellulose (CMC) mass fractions...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-191

    authors: Zhao H,Akiba N,Tanimoto H,Yoshizaki T,Yalikun K,Minakuchi S

    更新日期:2016-01-01 00:00:00

  • Degradation of dental ZrO2-based materials after hydrothermal fatigue. Part I: XRD, XRF, and FESEM analyses.

    abstract::The aim was to investigate the effect of simulated low-temperature degradation (s-LTD) and hydrothermal fatigue on the degradation of three ZrO(2)-based dental materials. Lava, IPS, and NanoZr discs were randomly assigned to (1) Control-Storage in distilled water at 37°C; (2) Aging at 134°C for 5 h (s-LTD); (3) Thermo...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2011-216

    authors: Perdigão J,Pinto AM,Monteiro RC,Braz Fernandes FM,Laranjeira P,Veiga JP

    更新日期:2012-01-01 00:00:00