Effect of air abrasion and thermocycling on resin adaptation and shear bond strength to dentin for an etch-and-rinse and self-etch resin adhesive.

abstract：:The aim of this investigation was to compare the cleaning and shaping efficiency of Self-adjusting file and Protaper, and to assess the correlation between root canal curvature and working time in mandibular molars using micro-computed tomography. Twenty extracted mandibular molars instrumented with Protaper and Self-...

journal_title：Dental materials journal

authors： Serefoglu B,Piskin B

更新日期：2017-09-26 00:00:00

abstract：:Atmospheric-pressure cold plasma was applied to process the surface of heat-polymerized acrylic resin. Changes to the physical properties and early adherence of Candida albicans were investigated. Alternating current cold plasma with Ar/O2 as working gas was used. Scanning electron microscopy (SEM) and X-ray photoelec...

journal_title：Dental materials journal

authors： Pan H,Wang G,Pan J,Ye G,Sun K,Zhang J,Wang J

更新日期：2015-01-01 00:00:00

abstract：:To elucidate the cause of brittleness of porcelain fused to pure titanium (PFPT) which leads to chipping and cracking similar to that of conventional porcelain in clinical use, fracture toughness KIc, hardness (Hv and Hk) and fracture energy gamma reflecting the bonding energy of atoms were evaluated. In KIc there wer...

journal_title：Dental materials journal

authors： Higashino Y,Yamauchi M,Goto T,Nagasawa T

更新日期：2003-12-01 00:00:00

abstract：:The effect of acidic fluoride solution on NiTi arch wires was examined by testing crystal structure, tensile strength, morphology after fracture, and element release from wire under four different test solutions after 1 or 3 d immersion. Three-day immersion in a 0.2%/pH 4 solution did not form any new crystal structur...

journal_title：Dental materials journal

authors： Kwon YH,Cheon YD,Seol HJ,Lee JH,Kim HI

更新日期：2004-12-01 00:00:00

abstract：:The aim of this study was to determine the effect of autoclave polymerization on the transverse strength of denture base polymers. To this end, 30 rectangular test specimens were fabricated of two heat-polymerized denture base polymers. The test groups were: (I) control, i.e., conventional water bath to polymerize res...

journal_title：Dental materials journal

authors： Durkan R,Ozel MB,Bağiş B,Usanmaz A

更新日期：2008-07-01 00:00:00

abstract：:To improve the bioactivity of titanium surfaces, glow discharge was used to facilitate collagen grafting on titanium disks. Titanium test specimens were pre-treated by glow discharge fed with a mixture of argon and allylamine (AA) gases. Treated titanium disks were then grafted with type I collagen using glutaraldehyd...

journal_title：Dental materials journal

authors： Chang WJ,Ou KL,Lee SY,Chen JY,Abiko Y,Lin CT,Huang HM

更新日期：2008-05-01 00:00:00

abstract：:Glass-ceramic powders with the oxide batch formulation 50wt%SiO2, 20wt%P2O5 and 30wt%CaO were prepared by the sol-gel process using tetraethoxysilane, calcium nitrate and phosphoric acid as raw materials. The obtained gels and powders were characterized by TG-DTA thermal analysis, FTIR analyses and XRD measurements. T...

journal_title：Dental materials journal

authors： Taira M,Okazaki M,Takahashi J

更新日期：1997-12-01 00:00:00

abstract：:Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to i...

journal_title：Dental materials journal

authors： Tanimoto Y,Nagakura M

更新日期：2018-11-30 00:00:00

abstract：:The purpose of this study was to investigate the effects of the location and orientation of dentinal tubules in the tooth on tensile strengths of the dentin. Dumbbell-shaped specimens of 12 groups from various locations and dentinal tubule orientations were prepared. The tensile test was performed in distilled water a...

journal_title：Dental materials journal

authors： Inoue T,Takahashi H,Nishimura F

更新日期：2002-03-01 00:00:00

abstract：:The corrosion behavior of three Ni-Ti alloys with compositions as commercial super-elastic orthodontic wires was investigated using polished plate specimens. Corrosion resistance was estimated by potentiodynamic polarization measurement in 0.9% NaCl and 1% lactic acid solutions and analysis of released metals by atomi...

journal_title：Dental materials journal

authors： Iijima M,Endo K,Ohno H,Mizoguchi I

更新日期：1998-03-01 00:00:00

abstract：:The purpose of this study was to investigate the effect of remaining dentin thickness (RDT) and long term water storage on dentin bond strength in-vitro. Twenty-seven third molars were randomly divided into 3 groups: Clearfil Bond SE ONE (SE1, Kuraray Noritake Dental, Okayama, Japan), G-Bond plus (GB, GC, Tokyo, Japan...

journal_title：Dental materials journal

authors： Ting S,Chowdhury AFMA,Sun J,Kakuda S,Sidhu SK,Yoshida Y,Selimovic D,Sano H

更新日期：2018-07-29 00:00:00

abstract：:The aim of this study was to investigate in how far the way the specimen is fixed to the testing device influences the micro-tensile bond strength of adhesives to dentin. Compared to a flat jig, a notched jig enables the specimen to be aligned easier and more accurately perpendicular to the interface, thereby concentr...

journal_title：Dental materials journal

authors： Poitevin A,De Munck J,Van Landuyt K,Coutinho E,Peumans M,Lambrechts P,Van Meerbeek B

更新日期：2007-09-01 00:00:00

abstract：:Effects of functionally gradient calcium phosphate consisting of hydroxyapatite (HAP) and alpha-tricalcium phosphate (alpha-TCP) on proliferation and differentiation of osteoblasts were evaluated using MC3T3-E1 cells. There were no significant differences in the proliferation of MC3T3-E1 cells among HAP-alpha-TCP func...

journal_title：Dental materials journal

authors： Yuasa T,Miyamoto Y,Kon M,Ishikawa K,Takechi M,Momota Y,Tatehara S,Takano H,Mimamiguchi S,Nagayama M

更新日期：2005-06-01 00:00:00

abstract：:This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...

journal_title：Dental materials journal

authors： Fujita R,Komada W,Nozaki K,Miura H

更新日期：2014-01-01 00:00:00

abstract：:The aim of this study was to investigate and compare the radio-opacity of core materials for all-ceramic restorations, such as zirconia (NANOZR and Y-TZP) and alumina, against commercially pure titanium (cpTi) and aluminum. X-ray images were taken under general settings using an X-ray film. The X-ray film images were ...

journal_title：Dental materials journal

authors： Okuda Y,Noda M,Kono H,Miyamoto M,Sato H,Ban S

更新日期：2010-01-01 00:00:00

abstract：:Seven types of amide monomers, methacryloyl tyrosine amide (MTYA), p-methacryloxybenzamide (p-MBA), p-methacryloxybutoxybenzamide (p-MBBA), o-methacryloxybutoxybenzamide (o-MBBA), p-methacryloxybutoxy phenylpropionamide (p-MBPPA), 3,5-dimethacryloxybenzamide (3,5-DMBA), and 3,5-di (methacryloxybutoxy)benzamide (3,5-DM...

journal_title：Dental materials journal

authors： Hayakawa T,Horie K

更新日期：1991-12-01 00:00:00

abstract：:To recognize good mechanical properties and water-resistance of a dental resin, dimethacryloxyethyl-1,1,6,6-tetrahydro-perfluoro-hexamethylene-1,6-dicarbamate (FDMHD) was newly synthesized. FDMHD initially was a white powder with m.p. 98.5-99.5°C. The copolymers of FDMHD and methyl methacrylate (MMA), FDMHD/MMA copoly...

journal_title：Dental materials journal

authors： Kurata S,Yamazaki N

更新日期：2011-01-01 00:00:00

abstract：:Gold alloys with Cu contents of 10 mass%, 20%, and 30% were used for morphological observation of porous surface structures after heating at 800 degrees C in air followed by pickling with acid solution. With increasing Cu content in the gold alloy, the internal oxidation zone became well-developed in the alloy matrix....

journal_title：Dental materials journal

authors： Ohno H,Endo K,Haneda K,Tamura M,Hikita K

更新日期：2005-12-01 00:00:00

abstract：:The purpose of this study was to evaluate the effects of ultrasonic and manual placement techniques on the push-out bond strength of Biodentine and MTA with and without calcium chloride. One hundred and twenty mid-root slices from forty freshly extracted single-rooted human mandibular premolar teeth were instrumented ...

journal_title：Dental materials journal

authors： Küçükkaya Eren S,Aksel H,Serper A

更新日期：2016-10-01 00:00:00

abstract：:Chemical mechanical polishing (CMP) of cpTi (Ti) was carried out using two types of slurries, acidic and basic colloidal silica containing H2O2 up to 3 wt%, to obtain flat and mirror-polished surfaces without any contaminated and reacted layers. Polishing behavior and surface properties were investigated using AFM, EP...

journal_title：Dental materials journal

authors： Okawa S,Watanabe K

更新日期：2009-01-01 00:00:00

abstract：:The purpose of this study was to devise and propose appropriate conditions for the photographing of thermal images in the oral cavity and to evaluate which thermography techniques can be applied to dentistry by evaluating the differences in temperature among oral tissues. Thermal images of oral cavities of 20 voluntee...

journal_title：Dental materials journal

authors： Komoriyama M,Nomoto R,Tanaka R,Hosoya N,Gomi K,Iino F,Yashima A,Takayama Y,Tsuruta M,Tokiwa H,Kawasaki K,Arai T,Hosoi T,Hirashita A,Hirano S

更新日期：2003-12-01 00:00:00

abstract：:The depths of cure and the distributions of degree of conversion (DC), polymerization conversion (PC) and percent pendant double bonds (PDB) of light-cured composite resins cured under various intensities of light were investigated. When the total amount of exposure, represented by the product of the light intensity a...

journal_title：Dental materials journal

authors： Nomoto R,Uchida K,Hirasawa T

更新日期：1994-12-01 00:00:00

abstract：:This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal floor dentin were restored with a two-step self-etch adhesive system, Clearfil Liner Bond 2V and a composite core, Cle...

journal_title：Dental materials journal

authors： Ariyoshi M,Nikaido T,Foxton RM,Tagami J

更新日期：2010-10-01 00:00:00

abstract：:The mechanical properties of polycarboxylate cements containing 20 mass% of four kinds of aluminoborate whiskers with different fiber lengths and diameters were evaluated. Bending strength of the cements increased with increase in fiber length, whereby the strength of the cement with the longest fiber was about two ti...

journal_title：Dental materials journal

authors： Kurata S,Umemoto K

更新日期：2008-07-01 00:00:00

abstract：:Though zirconia has been used in dental implant fixtures, the biocompatibility of the zirconia surface is not optimal for the surrounding tissue, and many surface modifications have been attempted. We have developed a novel method for improving the biocompatibility of zirconia by incorporating Ca ions. Elemental analy...

journal_title：Dental materials journal

authors： Sasaki K,Hayashi T,Asakura M,Ando M,Kawai T,Ban S

更新日期：2015-01-01 00:00:00

abstract：:The use of a single metal for all restorations would be necessary because it protects against metal corrosion caused by the contact of different metals. For this "one-metal rehabilitation" concept, non-alloyed commercially pure (CP) titanium should be used for all restorations. Titanium frameworks have been cast and u...

journal_title：Dental materials journal

authors： Ohkubo C,Sato Y,Nishiyama Y,Suzuki Y

更新日期：2017-09-26 00:00:00

abstract：:The objective of this study was to clarify the effect of surface topography on osteoblast-like cell behavior on yttria stabilized tetragonal zirconia polycrystals (TZP). Mirror-polished; blasted with 50- or 150-µm alumina (SB50 and SB150); and SB150 acid-etched with hydrofluoric acid (SB150E) were prepared on TZP. Ini...

journal_title：Dental materials journal

authors： Ito H,Sasaki H,Saito K,Honma S,Yajima Y,Yoshinari M

更新日期：2013-01-01 00:00:00

abstract：:This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...

journal_title：Dental materials journal

authors： de Carvalho RF,Martins ME,de Queiroz JR,Leite FP,Ozcan M

更新日期：2011-01-01 00:00:00

abstract：:This study was designed to examine the effects of dose of recombinant human BMP-2 (rhBMP-2) on bone formation at palatal sites in 10-week-old (10w) and 70-week-old (70w) rats, when combined with a polylactate-polyglycolate copolymer/gelatine sponge (PGS). New bone formation was observed at six weeks after implantation...

journal_title：Dental materials journal

authors： Yamaji K,Kawanami M,Matsumoto A,Odajima T,Nishitani Y,Iwasaka K,Yoshimitsu K,Yoshiyama M

更新日期：2007-07-01 00:00:00

abstract：:The objective of this study was to evaluate, using methylene blue (MB), the effects of various light sources on the bleaching action of hydrogen peroxide (H(2)O(2)) with two titanium dioxide (TiO(2)) photocatalysts - an ultraviolet light-activated TiO(2) photocatalyst (UVTiO(2)) versus a visible light-activated TiO(2)...

journal_title：Dental materials journal

authors： Suyama Y,Otsuki M,Ogisu S,Kishikawa R,Tagami J,Ikeda M,Kurata H,Cho T

更新日期：2009-11-01 00:00:00