Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin.

Abstract:

:This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal floor dentin were restored with a two-step self-etch adhesive system, Clearfil Liner Bond 2V and a composite core, Clearfil DC Core Automix, using different filling techniques and curing strategies. A flowable resin composite, Clearfil Flow FX was placed on the cured adhesive resin prior to restoration with a composite core. Packing the composite in the access cavity was performed in bulk with or without light curing or using an incremental technique with light curing. Microtensile bond strengths to pulpal floor dentin were measured after 24 hours storage in water. Light curing and incremental technique had positive effects on the MTBSs. Lining with a flowable resin composite did not significantly improve the MTBSs, however, influenced the failure mode after debonding. Non-lining and bulk filling with chemical curing strategy provided the lowest MTBS.

journal_name

Dent Mater J

journal_title

Dental materials journal

authors

Ariyoshi M,Nikaido T,Foxton RM,Tagami J

doi

10.4012/dmj.2009-104

subject

Has Abstract

pub_date

2010-10-01 00:00:00

pages

562-9

issue

5

eissn

0287-4547

issn

1881-1361

pii

JST.JSTAGE/dmj/2009-104

journal_volume

29

pub_type

杂志文章
  • Influence of thin carbonate-containing apatite coating with molecular precursor method to zirconia on osteoblast-like cell response.

    abstract::The influence of a thin carbonate-containing hydroxyapatite (CA) coating to tetragonal zirconia polycrystal (TZP) on osteoblastlike cell response was investigated. TZP disks were subjected to blasting and acid etching. Thin CA coatings were deposited by the molecular precursor method (TZP-CA). Initial cell adhesion of...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2013-122

    authors: Kaneko H,Sasaki H,Honma S,Hayakawa T,Sato M,Yajima Y,Yoshinari M

    更新日期:2014-01-01 00:00:00

  • Cytotoxicity of dental resin monomers in the presence of S9 mix enzymes.

    abstract::The purpose of the this study was to evaluate the cytotoxicity of dental resin monomers in the presence of a rat liver S9 mix containing cytochrome P 450 enzymes. JTC-12 cells derived from a monkey kidney were seeded on a 96-well multi-well-plate at 9 x 10(3) cells per well. After cultivation, the S9 mix was added to ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.18.76

    authors: Hikage S,Sato A,Suzuki S,Cox CF,Sakaguchi K

    更新日期:1999-03-01 00:00:00

  • Analysis of fracture surface of titanium-porcelain bonding by electron spectroscopy for chemical analysis.

    abstract::Three commercially available porcelains bonded to titanium were evaluated to determine the weakest zone of the titanium-porcelain bonding structures. Tensile bond tests were performed for these specimens (NO, DU, and VI) and for Ni-Cr alloy-porcelain bonding samples that served as controls. The maximum bond strengths ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2013-263

    authors: Kannari Y,Endo K,Ida Y,Ochi M,Ohno H

    更新日期:2014-01-01 00:00:00

  • Pre-treatment of radicular dentin by self-etch primer containing chlorhexidine can improve fiber post bond durability.

    abstract::We evaluated whether the pre-treatment of radicular dentin by ED Primer containing different concentrations of chlorhexidine can improve the bond durability of fiber post to radicular dentin. Experimental ED primers containing different concentrations of chlorhexidine (0%, 0.5% and 1.0%) were prepared. Thirty extracte...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2012-134

    authors: Zhou J,Yang X,Chen L,Liu X,Ma L,Tan J

    更新日期:2013-01-01 00:00:00

  • Effect of surface preparation on the bond strength of heat-polymerized denture base resin to commercially pure titanium and cobalt-chromium alloy.

    abstract::The aim of this study was to investigate the bond durability of heat-polymerized denture base resin to cast CP Ti and Co-Cr alloy. The alloy specimens were divided into five groups: 1) airborne-particle abraded with 50 µm alumina (SAND), 2) Rocatec tribochemical silica coating system (RO), 3) air-abraded followed by a...

    journal_title:Dental materials journal

    pub_type: 杂志文章,随机对照试验

    doi:10.4012/dmj.2010-089

    authors: Kawaguchi T,Shimizu H,Lassila LV,Vallittu PK,Takahashi Y

    更新日期:2011-01-01 00:00:00

  • Effect of casting methods on castability of pure titanium.

    abstract::Two types of patterns were tested for castability: 1) polyester mesh pattern (20mm x 22mm with 100 open squares) and 2) 20mm x 20mm wax plates 1.0 and 1.5 mm in thickness. These materials were invested using a pre-arranged commercial phosphate-bonded investment for titanium. Three different types of casting machines w...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.12.245

    authors: Takahashi J,Zhang JZ,Okazaki M

    更新日期:1993-12-01 00:00:00

  • Abutment screw loosening of endosseous dental implant body/abutment joint by cyclic torsional loading test at the initial stage.

    abstract::Cyclic torsional loading tests were carried out in the laboratory using various implant systems, in order to clarify differences between the systems in loosening of abutment screws. Six samples from six commercially available abutment systems were used, giving a total of 36 samples. Four of the systems used internal c...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-023

    authors: Katsuta Y,Watanabe F

    更新日期:2015-01-01 00:00:00

  • The effect of five kinds of surface treatment agents on the bond strength to various ceramics with thermocycle aging.

    abstract::This study evaluated the effects of ceramic surface treatment agents on shear bond strengths to ceramic materials with and without thermocycling. Ceramic plates were prepared from feldspathic ceramic; AAA, lithium disilicate ceramic material; IPS e.max Press, zirconia ceramic; Lava. Ceramic surfaces were pretreated wi...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2016-383

    authors: Noda Y,Nakajima M,Takahashi M,Mamanee T,Hosaka K,Takagaki T,Ikeda M,Foxton RM,Tagami J

    更新日期:2017-11-29 00:00:00

  • Effects of a barbituric acid/CuCl2 initiator system on resin adhesion to dentin.

    abstract::The effectiveness of a barbituric acid/copper (II) chloride initiator system in dentin was examined in terms of the effects of barbituric acid structures and dentin conditioners on bond strength. Curing times and tensile bond strengths to bovine dentin were measured for PMMA/MMA resins in conjunction with initiators c...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.14.221

    authors: Suzuki A,Imai Y

    更新日期:1995-12-01 00:00:00

  • A new procedure of the tensile fatigue test for dental materials.

    abstract::A new tensile fatigue test using a stainless steel screw was introduced. A transparent PMMA rod was selected as the test material. A hole was drilled and tapped into the rod; a screw was put into the rod with dental cement or without cementation. Three types of cyclic loads were applied to the test piece; the number o...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.11.141

    authors: Nishimura F,Nakamura H,Watari F,Tanaka I,Takahashi H

    更新日期:1992-12-01 00:00:00

  • Deformation properties of Ti-6A1-7Nb alloy castings for removable partial denture frameworks.

    abstract::Ti-6Al-7Nb alloy was cast into three differently designed, removable partial denture frameworks: Palatal strap (PS), Anterior-posterior bar (AP), and Horseshoe-shaped bar (HS). The vertical displacement and local strain of Ti-6Al-7Nb alloy frameworks were investigated to compare against those of Co-Cr alloy frameworks...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.23.497

    authors: Srimaneepong V,Yoneyama T,Wakabayashi N,Kobayashi E,Hanawa T,Doi H

    更新日期:2004-12-01 00:00:00

  • The evaluation of the desensitization effect of a desensitizing agent and desensitizing toothpastes in vitro.

    abstract::This study was evaluating how three desensitizing toothpastes used at home influence the effect associated with desensitizing agents after application in the clinic. Fifty dentine disks measure it permeability and 32 dentine disks with similar permeability levels were selected. Following Dental desensitizer treatment,...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-164

    authors: Hu ML,Zheng G,Jiang RD,Han JM,Zhang YD,Lin H

    更新日期:2020-09-29 00:00:00

  • Effect of Cr and Cu addition on corrosion behavior of Ni-Ti alloys.

    abstract::The corrosion behavior of three Ni-Ti alloys with compositions as commercial super-elastic orthodontic wires was investigated using polished plate specimens. Corrosion resistance was estimated by potentiodynamic polarization measurement in 0.9% NaCl and 1% lactic acid solutions and analysis of released metals by atomi...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.17.31

    authors: Iijima M,Endo K,Ohno H,Mizoguchi I

    更新日期:1998-03-01 00:00:00

  • In vivo wear pattern of experimental composite resins containing different filler components.

    abstract::Using a scanning electron microscope (SEM) and an electron probe surface roughness analyzer (ERA), we conducted the in vivo study of the effect of various filler components on the wear of composite resins. Experimental light-cured composite resins were prepared employing three different filler components; -(1) Silica ...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.13.36

    authors: Sekiya K,Okamoto A,Fukushima M,Iwaku M

    更新日期:1994-06-01 00:00:00

  • Effect of surface modification on the photocatalysis of Ti-Ni alloy in orthodontics.

    abstract::Photocatalytic activity from the reaction of titanium oxide with ultraviolet light has recently gained much attention. In particular, there is scientific interest in inducing photocatalytic reactions on Ti-Ni alloy, a material widely used in orthodontic applications. However, it is believed that inducing a photocataly...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.26.924

    authors: Horiuchi Y,Horiuchi M,Hanawa T,Soma K

    更新日期:2007-11-01 00:00:00

  • Application of addition-cured silicone denture relining materials to adjust mouthguards.

    abstract::The purposes of this study were to examine the shock absorption capability of addition-cured silicone denture relining materials and the bonding strength of addition-cured silicone denture relining materials and a commercial mouthguard material to determine its applicability to mouthguard adjustment. Two addition-cure...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2015-378

    authors: Fukasawa S,Churei H,Chowdhury RU,Shirako T,Shahrin S,Shrestha A,Wada T,Uo M,Takahashi H,Ueno T

    更新日期:2016-01-01 00:00:00

  • Effectiveness of sodium hypochlorite and sulfinic acid sodium salt treatment on dentin-resin bonding: Long-term durability of one-step self-etching adhesive.

    abstract::This study aimed to evaluate the effect of sulfinic acid sodium salt interposition after acid and sodium hypochlorite treatment (NC treatment) on dentin bonding durability using a mild type one-step self-etching adhesive. Fifteen human third molars were randomly assigned into three experimental groups according to den...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2017-105

    authors: Nakatani H,Mine A,Matsumoto M,Kabetani T,Kawaguchi-Uemura A,Higashi M,Tajiri Y,Imai D,Hagino R,Minamino T,Miura J,Yatani H

    更新日期:2017-11-29 00:00:00

  • Influence of a propolis-based irrigant solution on gap formation and bond strength of posts bonded to root canal dentin using different resin cements.

    abstract::This study evaluated the influence of an aqueous propolis-based solution (PROP) on gap formation and bond strength of posts bonded to root canal dentin using resin cements. Endodontically-treated bovine incisors received different irrigation protocols: 1) 2.5% sodium hypochlorite (NaOCl)/17% EDTA/NaOCl; 2) saline solu...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-111

    authors: Matochek MHM,Tomaz PLS,Oliveira TS,Polassi MR,Alonso RCB,Scremin FM,Sauro S,Marcucci MC,D'Alpino PHP

    更新日期:2020-06-05 00:00:00

  • A comparison of the micro-shear bond strength and failure mode of non-enclosed and mold-enclosed luting cements bonded to metal.

    abstract::The objective of the study was to compare 1) the mean micro-shear bond strength and 2) failure mode of cements to metals in nonenclosed and mold-enclosed specimens. Specimens were prepared in mold-enclosed and non-enclosed formats from two RMGIC's and a self-adhesive resin-cement. 3-way ANOVA analysis and Tukey post h...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2013-065

    authors: Cheetham JJ,Palamara JE,Tyas MJ,Burrow MF

    更新日期:2013-01-01 00:00:00

  • Micro computed tomography evaluation of the Self-adjusting file and ProTaper Universal system on curved mandibular molars.

    abstract::The aim of this investigation was to compare the cleaning and shaping efficiency of Self-adjusting file and Protaper, and to assess the correlation between root canal curvature and working time in mandibular molars using micro-computed tomography. Twenty extracted mandibular molars instrumented with Protaper and Self-...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2016-255

    authors: Serefoglu B,Piskin B

    更新日期:2017-09-26 00:00:00

  • Nanostructure evaluation of healthy and fluorotic dentin by atomic force microscopy before and after phosphoric acid etching.

    abstract::The aim was to characterize by atomic force microscopy (AFM) the nanostructure of human dentin surfaces affected by dental fluorosis (DF) before and after phosphoric acid etching. This study included 240 human dentin samples classified according to the severity of DF, which were divided into four groups using the Thyl...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2011-023

    authors: Zavala-Alonso V,Aguilera-Flores R,Patiño-Marin N,Martinez-Castañon GA,Anusavice KJ,Loyola-Rodriguez JP

    更新日期:2011-01-01 00:00:00

  • A biocompatible model for evaluation of the responses of rat periapical tissue to a new zinc oxide-eugenol sealer.

    abstract::We aimed to establish an experimental animal model to evaluate materials for endodontic therapy. We focused on the biocompatibility of new paste-type zinc oxide-eugenol (ZOE) sealer. The results of this sealer were compared with those of conventional powder/liquid ZOE and eugenol-free sealers. The molars of Wistar rat...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2010-095

    authors: Mutoh N,Tani-Ishii N

    更新日期:2011-01-01 00:00:00

  • Bonding durability between orthodontic brackets and human enamel treated with megabond self-etching primer using 4-META/MMA-TBB resin cement.

    abstract::The purpose of this study was to determine the bonding durability when a Megabond self-etching primer is used with 4-META/MMA-TBB resin to bond metal orthodontic brackets to human premolar enamel. Three conditions of enamel were prepared: Megabond self-etching primer without saliva contamination, Megabond self-etching...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.23.251

    authors: Sirirungrojying S,Hayakawa T,Saito K,Meguro D,Nemoto K,Kasai K

    更新日期:2004-09-01 00:00:00

  • Influence of resin coating materials on Porphyromonas gingivalis attachment.

    abstract::Resin coating materials have been used for composite resin or provisional restoration in order to prevent plaque accumulation on their surfaces. However, it is not clear whether the coating materials influence attachment of periodontal bacteria. Therefore, we investigated the effect of resin coating materials on the a...

    journal_title:Dental materials journal

    pub_type: 杂志文章,随机对照试验

    doi:10.4012/dmj.2011-164

    authors: Kumada A,Matsuka Y,Mine A,Ono M,Uehara J,Sonoi N,Ito T,Takashiba S,Kuboki T

    更新日期:2012-02-03 00:00:00

  • Multi-purpose bonding performance of newly synthesized phosphonic acid monomers.

    abstract::Multi-purpose bonding performance of three kinds of newly synthesized phosphonic acid monomers was investigated. Methacryloxyalkyl or acryloxyalkyl phosphonoacetates of 6-MHPA, 6-AHPA, 10-MDPA were synthesized in 42.8-51.9% yields with a light yellow viscous liquid, and identified as new compounds by 1H NMR, IR, and e...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.26.105

    authors: Ikemura K,Tay FR,Nishiyama N,Pashley DH,Endo T

    更新日期:2007-01-01 00:00:00

  • Development of cell-hybrid artificial bone: effect of osteogenic differentiation of bone marrow stromal stem cells on bone formation with newly developed interconnected porous calcium hydroxyapatite.

    abstract::The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.26.162

    authors: Doi K,Kubo T,Hayashi K,Imura K,Akagawa Y

    更新日期:2007-03-01 00:00:00

  • The application of cellulose acetate replication sheets in enamel wear investigations.

    abstract::Surface replication is a nondestructive evaluation technique applied in examining surfaces' cracks/wear. This is quite valuable when the surface of interest cannot be further manipulated by cutting or polishing to fit directly under a microscope. Replication by acetate sheets is one of the techniques applied in indust...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2017-444

    authors: Ijbara M,Wada K,Wada J,Jayawardena JA,Miyashin M

    更新日期:2019-02-08 00:00:00

  • Effect of monomer structure on the mechanical properties of light-cured composite resins.

    abstract::The effects of monomer structure on the mechanical properties of visible light-cured composite resins based on the seven types of aromatic dimethacrylates were investigated. The results of this study suggested that the mechanical properties of the composite resins were dependent upon the chemical structure of the dime...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.8.40

    authors: Kawaguchi M,Fukushima T,Horibe T

    更新日期:1989-06-01 00:00:00

  • Influence of abutment model materials on the fracture loads of three-unit fixed dental prostheses.

    abstract::This study evaluated and compared the influence of different supporting abutment models on the fracture loads of three-unit fixed dental prostheses (FDPs) fabricated from the following materials (n=24/material): (i) IPS e.max CAD-on, (ii) IPS e.max ZirCAD, and (iii) Telio CAD. Twelve FDPs of each group were adhesively...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2013-344

    authors: Wimmer T,Erdelt KJ,Eichberger M,Roos M,Edelhoff D,Stawarczyk B

    更新日期:2014-01-01 00:00:00

  • Anti-demineralization characteristics of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes.

    abstract::This study investigated the anti-demineralization effects of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes. Thirty-five bovine root specimens were divided into five treatment groups, with seven specimens each coated with 1) MI varnish (MIV), 2) F varnish (FV), 3) PRG varnish I (PV), 4) PRG varn...

    journal_title:Dental materials journal

    pub_type: 杂志文章

    doi:10.4012/dmj.2019-396

    authors: Shiiya T,Kataoka A,Tomiyama K,Fujino F,Mukai Y

    更新日期:2020-11-11 00:00:00