Abstract:
:This study investigated the contrast ratio and grain size depending on sintering parameters of twelve different zirconia materials and compared with glass-ceramic (N=156, n=12 per group). Contrast ratio of all ceramics was measured using a spectrophotometer according to ISO 2471: 2008. Grain sizes of zirconia were determined by SEM. Data was analyzed using one-way ANOVA followed by post-hoc Scheffé-test, Kruskal-Wallis-H-test and Spearman correlation (p<0.05). The area under the sintering curve up 25°C (AUC25) and 1200°C (AUC1200) of zirconia was calculated. Glass-ceramic showed significantly lowest contrast ratio compared to zirconia. Final sintering temperature and AUC1200 influenced contrast ratio. Grain size was affected by final sintering temperature, sintering duration and AUC. Contrast ratio and grain size showed an association.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Stawarczyk B,Emslander A,Roos M,Sener B,Noack F,Keul Cdoi
10.4012/dmj.2014-056subject
Has Abstractpub_date
2014-01-01 00:00:00pages
591-8issue
5eissn
0287-4547issn
1881-1361pii
DN/JST.JSTAGE/dmj/2014-056journal_volume
33pub_type
杂志文章abstract::The purpose of this study was to evaluate the influence of heating, cast bonding, and subsequent polishing procedures on attractive force of magnetic attachments. Two magnetic attachment systems with keepers of different chemical compositions (Hicorexslim 3013, 447J1; Magfit EX400, AUM20) were employed. Keepers examin...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.393
更新日期:2007-05-01 00:00:00
abstract::This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:
更新日期:2011-01-01 00:00:00
abstract::This study investigated the anti-demineralization effects of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes. Thirty-five bovine root specimens were divided into five treatment groups, with seven specimens each coated with 1) MI varnish (MIV), 2) F varnish (FV), 3) PRG varnish I (PV), 4) PRG varn...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-396
更新日期:2020-11-11 00:00:00
abstract::Cyclic torsional loading tests were carried out in the laboratory using various implant systems, in order to clarify differences between the systems in loosening of abutment screws. Six samples from six commercially available abutment systems were used, giving a total of 36 samples. Four of the systems used internal c...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-023
更新日期:2015-01-01 00:00:00
abstract::The kinetic polymerization behavior of 2,2,2-trifluoroethyl methacrylate (TFEMA), 1,1,1,3,3,3-hexafluoroisopropyl methacrylate (HFIPMA), 2,2,2-trifluoroethyl acrylate (TFEA) and 1,1,1,3,3,3-hexafluoroisopropyl acrylate (HFIPA) was determined by isothermal differential scanning calorimetry (DSC) and high-performance li...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2010-054
更新日期:2010-10-01 00:00:00
abstract::The aim of the present study was to examine whether interconnected porous hydroxyapatite ceramics (IP-CHA) could be used as bone substitute for implant treatment in reconstructive surgery. We firstly assessed if surround of the titanium surface placed into granular or block-type IP-CHA can observe new bone formation i...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-169
更新日期:2013-01-01 00:00:00
abstract::We investigated the effects of CO2 laser irradiation combined with acidulated phosphate fluoride (APF) application on the demineralization of enamel. APF gel was applied to the buccal enamel of human premolars and CO2 laser was applied. After the specimens were immersed in demineralization solution for 72 h, they were...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-225
更新日期:2015-01-01 00:00:00
abstract::The aim of this study was to investigate the effects of potassium fluoride (KF) and sodium fluoride (NaF) in different concentrations on micro-shear bond strength (µSBS) and their protective effects against acid. The enamel blocks were treated with several concentrations of KF and NaF. For µSBS, Clearfil SE Bond 2 was...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2020-019
更新日期:2020-10-27 00:00:00
abstract::This study aimed to investigate the in vitro biological response of human dental pulp cells to glass ionomer cement (GIC, Fuji IX GP(®)) containing 2.5% magnesium carbonate apatite (MgCO(3)Ap). MgCO(3)Ap was synthesized by wet method and characterized using FT-IR, XPS, and SEM. Fuji IX GP(®) served as a control. Test ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-096
更新日期:2012-01-01 00:00:00
abstract::The aim of this investigation was to evaluate the metal-ceramic bonding of Au-1.6 wt% Ti alloy. Therefore, the coefficient of thermal expansion, modulus of elasticity, ceramic bonding strength, and hardness of Au-1.6 wt% Ti alloy were measured. The metal-ceramic interface was observed by EPMA to investigate its bondin...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.268
更新日期:2005-06-01 00:00:00
abstract::The effect of warm air-blowing on the sealing ability of two one-bottle and one two-bottle silane-containing universal adhesives (UAs) applied to lithium disilicate ceramics (LDS) was evaluated. Tapered cavities prefabricated in LDS blocks (IPS e.max CAD) were treated by the adhesives, air-blown either with normal air...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2020-057
更新日期:2020-10-24 00:00:00
abstract::The biaxial flexural strength and cyclic fatigue biaxial flexural strength of CAD/CAM ceramics polished with #220, 400, 600 and 1000 diamond pads were measured in an effort to determine the effect of surface roughness on fatigue behavior of dental ceramics. The surface roughness was improved after polishing with a sma...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.18.395
更新日期:1999-12-01 00:00:00
abstract::This study aimed to evaluate the effect of sulfinic acid sodium salt interposition after acid and sodium hypochlorite treatment (NC treatment) on dentin bonding durability using a mild type one-step self-etching adhesive. Fifteen human third molars were randomly assigned into three experimental groups according to den...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-105
更新日期:2017-11-29 00:00:00
abstract::Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to i...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2018-012
更新日期:2018-11-30 00:00:00
abstract::The corrosion behavior of three Ni-Ti alloys with compositions as commercial super-elastic orthodontic wires was investigated using polished plate specimens. Corrosion resistance was estimated by potentiodynamic polarization measurement in 0.9% NaCl and 1% lactic acid solutions and analysis of released metals by atomi...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.17.31
更新日期:1998-03-01 00:00:00
abstract::Atmospheric-pressure cold plasma was applied to process the surface of heat-polymerized acrylic resin. Changes to the physical properties and early adherence of Candida albicans were investigated. Alternating current cold plasma with Ar/O2 as working gas was used. Scanning electron microscopy (SEM) and X-ray photoelec...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-035
更新日期:2015-01-01 00:00:00
abstract::This study evaluated the polymerization shrinkage, flexural and compressive properties of low-shrinkage resin composites. For the study, four methacrylate-based and one silorane-based resin composites were light cured using three different light-curing units (LCUs) and their polymerization shrinkage, flexural (strengt...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-126
更新日期:2014-01-01 00:00:00
abstract::The aim of this study was to investigate the bond durability of heat-polymerized denture base resin to cast CP Ti and Co-Cr alloy. The alloy specimens were divided into five groups: 1) airborne-particle abraded with 50 µm alumina (SAND), 2) Rocatec tribochemical silica coating system (RO), 3) air-abraded followed by a...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:10.4012/dmj.2010-089
更新日期:2011-01-01 00:00:00
abstract::This study examined the surface microhardness of four kinds of resin composites with different fillers and resin matrices. Ten specimens of 2 mm thickness and 4 mm diameter of each resin composite were polymerized using a halogen light, a blue light-emitted diode, and a plasma arc unit. Microhardness evaluation was pe...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:
更新日期:2007-11-01 00:00:00
abstract::The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.162
更新日期:2007-03-01 00:00:00
abstract::The study evaluated changes in total enzymatic activity and degradation of demineralized dentin following the application of universal or self-etch adhesives. The universal adhesives -Scotchbond Universal (SU) and All-Bond Universal (ABU) and self-etch adhesives -Adper Easy Bond (EB) and G-aenial Bond (GB) were used f...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-304
更新日期:2020-12-03 00:00:00
abstract::Novel fast-setting calcium silicate cement with fluoride (CSC) has been developed for potential applications in tooth crown. The aim of this study was to test the diametral tensile strength (DTS) of different CSC compositions in humid condition on day1, 28, and 180. We tested 'bond CSC' with 3.5% fluoride and no radio...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-390
更新日期:2016-01-01 00:00:00
abstract::The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.15.212
更新日期:1996-12-01 00:00:00
abstract::A new type of self-etching agent, the single-step adhesive, was developed. The purpose of this study was to investigate the difference in the ultrastructural features of enamel and dentin surfaces following application of the prototype single-step adhesive (EXM618, 3M, MN, USA). Extracted caries-free human premolars w...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.321
更新日期:2004-09-01 00:00:00
abstract::The objective of this study was to examine the effects of storage conditions on the flexural strengths of resin composite materials for CAD/CAM restorations. Seven commercially available resin composite CAD/CAM blanks were examined. Rectangular specimens (4.0×1.2×4.0 mm) of each material were trimmed from the blanks a...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-202
更新日期:2020-09-29 00:00:00
abstract::The aim of this in vitro study was to evaluate the effects of different preparation angles on the precision of fit of zirconia crown frameworks. Dies were fabricated with three different preparation angles: 4, 8, and 12 degrees total taper. Ten copings were fabricated for each angle by a laboratory and a milling-cente...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.814
更新日期:2008-11-01 00:00:00
abstract::This study evaluated the influence of an aqueous propolis-based solution (PROP) on gap formation and bond strength of posts bonded to root canal dentin using resin cements. Endodontically-treated bovine incisors received different irrigation protocols: 1) 2.5% sodium hypochlorite (NaOCl)/17% EDTA/NaOCl; 2) saline solu...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-111
更新日期:2020-06-05 00:00:00
abstract::The depths of calcium-ion incorporation into a commercially pure titanium and an experimental beta-type titanium alloy were determined using Auger electron spectroscopy. After the electrochemical deposition of apatite, new compositional gradients appeared in the profiles in which the Ca and P concentrations gradually ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.21.306
更新日期:2002-12-01 00:00:00
abstract::The purpose of this study was to clarify the effect of silver nanoparticles on the behavior of subcritical crack growth (SCG) in dental porcelains. Prior to occurrence of fast fracture in dental porcelains, SCG occurs and leads to strength degradation over time. SCG in dental porcelains can be characterized by the str...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-266
更新日期:2013-01-01 00:00:00
abstract::This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal floor dentin were restored with a two-step self-etch adhesive system, Clearfil Liner Bond 2V and a composite core, Cle...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2009-104
更新日期:2010-10-01 00:00:00