Abstract:
:Novel fast-setting calcium silicate cement with fluoride (CSC) has been developed for potential applications in tooth crown. The aim of this study was to test the diametral tensile strength (DTS) of different CSC compositions in humid condition on day1, 28, and 180. We tested 'bond CSC' with 3.5% fluoride and no radiocontrast, 'CSC' with 3.5% fluoride and 10% radiocontrast, 'ultrafast CSC' with 3.5% fluoride and 20% radiocontrast, 'high fluoride CSC' with 15% fluoride and 25% radiocontrast, Biodentine, and MTA. We filled the cements after mixing to cylindrical molds. Specimens were stored in >95% humidity. DTS was measured at each time point. CSC compositions had statistically higher DTS compared to MTA and Biodentine on day1. Bond CSC showed higher DTS versus all cements, except CSC, at all time points. DTS of all cements, except Biodentine, significantly increased in humid condition on day28 and day180 compared to day1.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Ranjkesh B,Isidor F,Dalstra M,Løvschall Hdoi
10.4012/dmj.2015-390subject
Has Abstractpub_date
2016-01-01 00:00:00pages
559-63issue
4eissn
0287-4547issn
1881-1361journal_volume
35pub_type
杂志文章abstract::Ti-6Al-7Nb alloy was cast into three differently designed, removable partial denture frameworks: Palatal strap (PS), Anterior-posterior bar (AP), and Horseshoe-shaped bar (HS). The vertical displacement and local strain of Ti-6Al-7Nb alloy frameworks were investigated to compare against those of Co-Cr alloy frameworks...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.497
更新日期:2004-12-01 00:00:00
abstract::This study aimed to determine the influence of sodium hypochlorite (NaOCl) contamination on the microhardness of build-up composites. Fifty-two samples, from each of three build-up materials (LuxaCore Dual, MultiCore flow and Rebilda DC) were prepared. Half of the samples from each material were stored in physiologic ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2010-007
更新日期:2010-08-01 00:00:00
abstract::Chemical mechanical polishing (CMP) of cpTi (Ti) was carried out using two types of slurries, acidic and basic colloidal silica containing H2O2 up to 3 wt%, to obtain flat and mirror-polished surfaces without any contaminated and reacted layers. Polishing behavior and surface properties were investigated using AFM, EP...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.28.68
更新日期:2009-01-01 00:00:00
abstract::Miniplates have been used during the last decade to facilitate stability between bony fragments in the maxillofacial region and are currently the preferred surgical method for the fixation of fractures and osteotomies. The aim of this study was to evaluate and compare the biomechanical behaviors of six different types...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-315
更新日期:2014-01-01 00:00:00
abstract::This study evaluated the biomineralization and dentinal tubules occlusion abilities of the carboxyl-terminated polyamidoamine dendrimer (PAMAM-COOH) on human demineralized dentin in vivo at different time points. Demineralization dentin model with and without treated with PAMAM-COOH were sutured to the interior side o...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-209
更新日期:2016-01-01 00:00:00
abstract::Glass-ceramic powders with the oxide batch formulation 50wt%SiO2, 20wt%P2O5 and 30wt%CaO were prepared by the sol-gel process using tetraethoxysilane, calcium nitrate and phosphoric acid as raw materials. The obtained gels and powders were characterized by TG-DTA thermal analysis, FTIR analyses and XRD measurements. T...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.16.117
更新日期:1997-12-01 00:00:00
abstract::To evaluate the cytotoxicity of resin cements on dental pulp-derived cells (bDPCs), Bifix QM (BQM), Choice 2(C2), RelyX U200(RU200), Maxcem Elite(ME), and Multilink Automix(MA) were tested. The materials were incubated in DMEM for 72 h. A real-time cell analyzer was used to evaluate cell survival. The statistical anal...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-167
更新日期:2015-01-01 00:00:00
abstract::This study evaluated the effects of combining enamel microabrasion and dental bleaching on the physical properties of enamel, using in vitro and in situ conditions and evaluating surface roughness, enamel microhardness and scanning electron microscopy images. One hundred sound bovine teeth were sectioned and cut into ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-334
更新日期:2016-01-01 00:00:00
abstract::The purposes of this study were to examine the shock absorption capability of addition-cured silicone denture relining materials and the bonding strength of addition-cured silicone denture relining materials and a commercial mouthguard material to determine its applicability to mouthguard adjustment. Two addition-cure...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-378
更新日期:2016-01-01 00:00:00
abstract::The objective of this work was to analyze the antimicrobial and antibiofilm activities of bismuth lipophilic nanoparticles (BisBAL NPs) incorporated into chitosan-based membranes. Chitosan-based membranes were homogeneously embedded with BisBAL NPs, confirming the bismuth presence by scanning electron microscopy. The ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2018-173
更新日期:2019-07-31 00:00:00
abstract::This study aimed to evaluate the effect of an acidic-adjusted pH of solvent in silanization on the amount of fluoride released and mechanical properties of heat-cured acrylic resin containing a silanized fluoride-releasing filler. The experimental groups were divided into 4 groups; non-silanized, acidic-adjusted pH, n...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-403
更新日期:2016-01-01 00:00:00
abstract::Cyclic torsional loading tests were carried out in the laboratory using various implant systems, in order to clarify differences between the systems in loosening of abutment screws. Six samples from six commercially available abutment systems were used, giving a total of 36 samples. Four of the systems used internal c...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-023
更新日期:2015-01-01 00:00:00
abstract::We aimed to establish an experimental animal model to evaluate materials for endodontic therapy. We focused on the biocompatibility of new paste-type zinc oxide-eugenol (ZOE) sealer. The results of this sealer were compared with those of conventional powder/liquid ZOE and eugenol-free sealers. The molars of Wistar rat...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2010-095
更新日期:2011-01-01 00:00:00
abstract::Major histocompatibility complex (MHC) class II molecule-expressing cells and macrophages play a pivotal role in mediating the host tissue response to biomaterials. This study investigated the responses of these cells to epoxy resin-based and 4-META-containing, methacrylate resin-based endodontic sealers (AH Plus and ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-005
更新日期:2013-01-01 00:00:00
abstract::This study compared differences in discoloration and dissolution in several titanium alloys with immersion in peroxide- or fluoride-containing solution. Commercially pure titanium (CP-Ti) and six titanium-based alloys were used: Ti-0.15Pd, Ti-6Al-4V, Ti-7Nb-6Al, Ti-55Ni, Ti-10Cu, and Ti-20Cr. Two test solutions were p...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.117
更新日期:2008-01-01 00:00:00
abstract::Ag-Pd-Cu-Au alloy was subjected to a Thermo-Mechanical Analyzer to investigate high temperature properties up to its liquidus temperature. Microstructural examination and elemental analysis with EPMA were also conducted in the solid/liquid mixture region. The following conclusions were obtained. (1) The solidus temper...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.22.227
更新日期:2003-09-01 00:00:00
abstract::Photocatalytic activity from the reaction of titanium oxide with ultraviolet light has recently gained much attention. In particular, there is scientific interest in inducing photocatalytic reactions on Ti-Ni alloy, a material widely used in orthodontic applications. However, it is believed that inducing a photocataly...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.924
更新日期:2007-11-01 00:00:00
abstract::The aim of this study was to evaluate the pH at the surface of active or arrested carious dentin using a micro pH sensor, and to compare the relationship between different pH measurement techniques. Twenty extracted carious teeth were divided into two groups, active or arrested caries, according to predefined clinical...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.423
更新日期:2006-09-01 00:00:00
abstract::This study examined the antimicrobial/antifungal ability of a tissue conditioner containing a photocatalyst for Escherichia coli, Streptococcus mutans, Staphylococcus aureus and Candida albicans. The photocatalyst was mixed with tissue conditioners powders at concentrations of 0, 10, 15, and 20 wt%. Tissue conditioner...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2010-203
更新日期:2011-01-01 00:00:00
abstract::We examined the mold filling capacity and microhardness of two industrial 1% Fe titanium alloys: Super-TIX800 (Nippon Steel Corp.) (Fe: 0.910%, O: 0.370%, N: 0.005%) and Super-TIX800N (Nippon Steel Corp.) (Fe: 0.960%, O: 0.300%, N: 0.041%). Two wedge-shaped acrylic patterns (with 30 degrees or 15 degrees angles) were ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.211
更新日期:2004-06-01 00:00:00
abstract::This study evaluated the effect of adding silane coupling agent on initial and long-term bond strengths of one-step self-etch adhesives to enamel-dentin-composite in combined situation. Cervical cavities were prepared on extracted molars and filled with Clearfil AP-X. After water-storage for one-week, the filled teeth...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-050
更新日期:2015-01-01 00:00:00
abstract::The blending effect (BE) plays an important role in esthetics of the composite resin. The objective of this study was to determine the extents to which filler size and content affect the BE. Three types of fillers (0.7, 1.0, and 1.5 µm) were mixed at weight contents of 60, 70, 75, and 80%. This study simulated clinica...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2016-083
更新日期:2017-01-31 00:00:00
abstract::The secretion of collagen by osteoblasts was observed by scanning electron microscopy (SEM). Osteoblast-like cells were cultured on a CO3apatite-collagen sponge reinforced with a porous HAp frame. After three days' incubation, a number of newly created matrix fibrils, forming a network structure, were observed at the ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.460
更新日期:2005-09-01 00:00:00
abstract::We investigated the adsorption of lipoteichoic acid (LTA) on titanium surfaces by using the quartz crystal microbalance (QCM) method, and confirmed the influence of mucin (MUC) pre-adsorption on LTA adsorption. Two injection methods were evaluated. Namely, Method A: single-step injection of LTA solution to the Ti sens...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-209
更新日期:2020-12-03 00:00:00
abstract::Finite element analysis was performed to evaluate stress distribution in maxillary central incisors treated endodontically and restored with a post and an all-ceramic crown. Tensile stress at tooth root was analyzed using two-dimensional finite element models with different post diameters and lengths. One post length ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.145
更新日期:2006-03-01 00:00:00
abstract::The purpose of this study was to investigate the effect of laser irradiation on the enamel surface spectroscopically. Polished bovine enamel surface was irradiated with an Er:YAG laser apparatus and chemically analyzed using X-ray photoelectron spectroscopy (XPS). XPS detected core electron peaks such as carbon (C 1s)...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.214
更新日期:2006-06-01 00:00:00
abstract::The influence of temperature and relative humidity (RH) on the bond strength of orthodontic adhesives was investigated. Two self-etching/composite type, one acid-etching/composite type, and one acid-etching/PMMA type of adhesives were examined under different temperature and RH conditions. Orthodontic brackets were bo...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.654
更新日期:2008-09-01 00:00:00
abstract::This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-303
更新日期:2014-01-01 00:00:00
abstract::The present study investigated the influences of a denture strengthener on the deformation of a maxillary complete denture. Three groups of maxillary complete dentures were fabricated (Group 1 without a strengthener; Group 2 with a Co-Cr alloy wire strengthener; Group 3 with an experimental fiberglass strengthener). T...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.28.507
更新日期:2009-07-01 00:00:00
abstract::Thermal misfit is deemed as one reason for the chipping of veneered zirconia restorations. Aim of the present study was to assess the effect of thermal misfit on the fracture load of veneered zirconia frameworks and to evaluate the applicability of a universal veneering ceramic for both zirconia and titanium framework...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.766
更新日期:2007-11-01 00:00:00