Abstract:
:To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding groups, contraction gap width of sclerotic dentin was significantly smaller than that of sound dentin when the cavity was not primed with glyceryl monomethacrylate. For each individual tooth, the correlation between contraction gap width and shear bond strength was insignificant. In conclusion, the bonding efficacy of dentin bonding systems to sclerotic dentin was superior to that of sound dentin. Further, it was determined that it was impossible to detect the interaction between the polymerization contraction stress of resin composites and the efficacy of dentin adhesives by measuring bond strength.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Kusunoki M,Itoh K,Takahashi Y,Hisamitsu Hdoi
10.4012/dmj.25.576subject
Has Abstractpub_date
2006-09-01 00:00:00pages
576-83issue
3eissn
0287-4547issn
1881-1361journal_volume
25pub_type
杂志文章abstract::This study evaluated the effects of combining enamel microabrasion and dental bleaching on the physical properties of enamel, using in vitro and in situ conditions and evaluating surface roughness, enamel microhardness and scanning electron microscopy images. One hundred sound bovine teeth were sectioned and cut into ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-334
更新日期:2016-01-01 00:00:00
abstract::Glass-ceramic powders with the oxide batch formulation 50wt%SiO2, 20wt%P2O5 and 30wt%CaO were prepared by the sol-gel process using tetraethoxysilane, calcium nitrate and phosphoric acid as raw materials. The obtained gels and powders were characterized by TG-DTA thermal analysis, FTIR analyses and XRD measurements. T...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.16.117
更新日期:1997-12-01 00:00:00
abstract::Though zirconia has been used in dental implant fixtures, the biocompatibility of the zirconia surface is not optimal for the surrounding tissue, and many surface modifications have been attempted. We have developed a novel method for improving the biocompatibility of zirconia by incorporating Ca ions. Elemental analy...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-199
更新日期:2015-01-01 00:00:00
abstract::This study investigated the effects of spherical silica fillers on the physical and mechanical properties of resin-modified glass-ionomer cement (RMGIC). Specimens were fabricated by mixing untreated (UF) or silanized (SF) spherical silica filler into the powder of a commercially prepared RMGIC. The original RMGIC and...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.146
更新日期:2004-06-01 00:00:00
abstract::Mechanical responses of the test specimen under bidirectional and unidirectional loading were investigated using a newly developed masticatory simulator. The simulator adopted a four-bar linkage mechanism to create both loading patterns. Scratch/occlusal contact characteristics, contact force profiles and the fracture...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2016-198
更新日期:2016-01-01 00:00:00
abstract::Although titanium has been widely used in prosthetic appliances, such as cast removable partial denture frameworks, high quality castings are still difficult to obtain. This study proposes a new partition technique using a metal foil for improving castability of a two-chamber pressure casting unit. The metal foil was ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.19.307
更新日期:2000-09-01 00:00:00
abstract::This study was carried out to investigate the influences of elastic moduli of the dowel-core combination on the stress distribution in the root by the use of 2-dimensional finite element analysis. The peak stress at the dowel-cement interface was influenced strongly by a change of elastic modulus of the post (from 20,...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.19.50
更新日期:2000-03-01 00:00:00
abstract::The aim of this study was to evaluate the bond strength of three adhesive systems: Excite™, Adper Prompt L-Pop™ and AdheSE One™ to varying degrees of fluorotic enamel using micro-tensile bond strength (μTBS) tests. Human enamel was classified according to the Thylstrup and Fejerskov Index. The interface resin-enamel w...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-140
更新日期:2012-01-01 00:00:00
abstract::The microstructure and homogeneity of three commercial dentin and incisal unfired porcelain frits (one conventional and two ultra-low fusing types, fused-to metal were analyzed by X-ray diffractometry, scanning electron microspectroscopy, and wavelength- and energy dispersive X-ray microspectroscopy. The average conte...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.17.264
更新日期:1998-12-01 00:00:00
abstract::Application of a light-cured porcelain margin is a technique which has been developed recently. In this study, we compared the porcelain margin properties of the porcelain-light-cured resin matrix system and the traditional porcelain-water system, in terms of volumetric shrinkage, density, compressive strength, surfac...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.14.1
更新日期:1995-06-01 00:00:00
abstract::A new type of self-etching agent, the single-step adhesive, was developed. The purpose of this study was to investigate the difference in the ultrastructural features of enamel and dentin surfaces following application of the prototype single-step adhesive (EXM618, 3M, MN, USA). Extracted caries-free human premolars w...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.321
更新日期:2004-09-01 00:00:00
abstract::The purpose of this study was to evaluate the effect of osteogenic differentiation of bone marrow stromal stem cells (BMSCs) on bone formation in a novel interconnected porous calcium hydroxyapatite (IP-CHA). BMSCs/IP-CHA composites, as a cell-hybrid artificial bone, were made by injecting BMSCs solution into IP-CHA s...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.162
更新日期:2007-03-01 00:00:00
abstract::The purpose of this study was to examine the effect of an electro-ionizing toothbrush with stannous fluoride in the treatment of dentin hypersensitivity following periodontal surgery. Thirty-two volunteers with dentin hypersensitivity were divided in two equal groups each using different methods: (Group I) stannous fl...
journal_title:Dental materials journal
pub_type: 临床试验,杂志文章,随机对照试验
doi:10.4012/dmj.20.164
更新日期:2001-06-01 00:00:00
abstract::This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:
更新日期:2011-01-01 00:00:00
abstract::The effects of desensitizer, disinfectant, saliva, blood, and hydrogen peroxide on the tensile bond strength between adhesive and ceramic as well as between adhesive and dentin were examined. Sixty 7x3 mm pressed ceramic discs of IPS e.max were fabricated and randomly assigned to six groups of different dentin surface...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:10.4012/dmj.2009-074
更新日期:2010-08-01 00:00:00
abstract::To determine new developed light curing units with shorter curing times effects on microleakage and microhardness values for resin fissure sealants. Resin filled sealant (UltraSeal-XT), resin unfilled sealant (Delton Type-II) and ormocer-based sealant (Admira-Seal) were light cured with a quartz-tungsten-halogen (QTH)...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-357
更新日期:2016-01-01 00:00:00
abstract::The influence of a thin carbonate-containing hydroxyapatite (CA) coating to tetragonal zirconia polycrystal (TZP) on osteoblastlike cell response was investigated. TZP disks were subjected to blasting and acid etching. Thin CA coatings were deposited by the molecular precursor method (TZP-CA). Initial cell adhesion of...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-122
更新日期:2014-01-01 00:00:00
abstract::Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to i...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2018-012
更新日期:2018-11-30 00:00:00
abstract::This study investigated the anti-demineralization effects of surface pre-reacted glass-ionomer (S-PRG) filler-containing varnishes. Thirty-five bovine root specimens were divided into five treatment groups, with seven specimens each coated with 1) MI varnish (MIV), 2) F varnish (FV), 3) PRG varnish I (PV), 4) PRG varn...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-396
更新日期:2020-11-11 00:00:00
abstract::The purpose of this review is to summarise recent advances in the design and composition of bioactive surface layers of implantabile biomaterials, and thus the genetic potential of osteoprogenitor cells to recognize and respond to these diverse implanted biomaterials. Changes applied to a biomaterial's surface, in gen...
journal_title:Dental materials journal
pub_type: 杂志文章,评审
doi:10.4012/dmj.19.99
更新日期:2000-06-01 00:00:00
abstract::Temperature dependencies of thermal expansion coefficients for the alloys of Pd-Ag, Pd-Cu and Pd-Co binary systems were measured at temperatures up to 900 degrees C, with heating and cooling rates of 5 degrees C/min. The coefficient of thermal expansion of alloys with no transformation in the temperature range of inte...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.9.47
更新日期:1990-06-01 00:00:00
abstract::The aim was to investigate the effect of simulated low-temperature degradation (s-LTD) and hydrothermal fatigue on the degradation of three ZrO(2)-based dental materials. Lava, IPS, and NanoZr discs were randomly assigned to (1) Control-Storage in distilled water at 37°C; (2) Aging at 134°C for 5 h (s-LTD); (3) Thermo...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-216
更新日期:2012-01-01 00:00:00
abstract::We evaluated the effect of different curing strategies for universal adhesives on micro-tensile bond strength (μTBS) between resin cement and dentin and/or between resin cement and indirect resin composite. Flat coronal dentin surfaces and composite resin disks were pretreated with silane-containing universal adhesive...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-240
更新日期:2018-06-08 00:00:00
abstract::The clinical feasibility of a novel device called a Cariotester was investigated by measuring the Knoop hardness (KHN) of white spot lesions diagnosed as ICDAS code 1, 2 or 3. To obtain an equation for converting the Cariotester indentation depth into the KHN, a regression analysis was performed between the depth and ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-282
更新日期:2015-01-01 00:00:00
abstract::The aim of this study was to investigate the relationship between the different mechanical properties with the filler fraction of various resin composites. Mechanical properties of eighteen different resin composites were investigated in this study; flexural strength (FS), flexural modulus (FM), fracture toughness (FT...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-178
更新日期:2013-01-01 00:00:00
abstract::The aim of this study was to investigate the effect of three metal priming agents on the bond strength of adhesive resin cement to Silver-Zinc-Tin-Indium (Ag-Zn-Sn-In) alloy and pure Ag, Zn, Sn, and In. The specimens were air-abraded with alumina and then primed with one of three metal priming agents: V-Primer, Esteni...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-139
更新日期:2018-03-30 00:00:00
abstract::Seven types of amide monomers, methacryloyl tyrosine amide (MTYA), p-methacryloxybenzamide (p-MBA), p-methacryloxybutoxybenzamide (p-MBBA), o-methacryloxybutoxybenzamide (o-MBBA), p-methacryloxybutoxy phenylpropionamide (p-MBPPA), 3,5-dimethacryloxybenzamide (3,5-DMBA), and 3,5-di (methacryloxybutoxy)benzamide (3,5-DM...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.10.165
更新日期:1991-12-01 00:00:00
abstract::The purpose of the present study was to analyze effective factors including periodontal ligament on vertical root fractures (VRFs). Eighty maxillary central incisors were assigned to eight groups, depending on master apical file (MAF) size, loading point and existence of a simulated periodontal ligament (PDL). The gut...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.66
更新日期:2005-03-01 00:00:00
abstract::The objective of this study was to evaluate, using methylene blue (MB), the effects of various light sources on the bleaching action of hydrogen peroxide (H(2)O(2)) with two titanium dioxide (TiO(2)) photocatalysts - an ultraviolet light-activated TiO(2) photocatalyst (UVTiO(2)) versus a visible light-activated TiO(2)...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.28.693
更新日期:2009-11-01 00:00:00
abstract::The aim of this study was to examine the lifespan or number of cycles to failure of tapered rotary nickel-titanium (Ni-Ti) endodontic instruments. Simulated root canals with different curvatures were used to determine a relation between canal curvature and instrument lifespan. Using a novel mathematical model for the ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-254
更新日期:2012-01-01 00:00:00