Development of fibroblast-seeded collagen gels under planar biaxial mechanical constraints: a biomechanical study.

Abstract:

:Prior studies indicated that mechanical loading influences cell turnover and matrix remodeling in tissues, suggesting that mechanical stimuli can play an active role in engineering artificial tissues. While most tissue culture studies focus on influence of uniaxial loading or constraints, effects of multi-axial loading or constraints on tissue development are far from clear. In this study, we examined the biaxial mechanical properties of fibroblast-seeded collagen gels cultured under four different mechanical constraints for 6 days: free-floating, equibiaxial stretching (with three different stretch ratios), strip-biaxial stretching, and uniaxial stretching. Passive mechanical behavior of the cell-seeded gels was also examined after decellularization. A continuum-based two-dimensional Fung model was used to quantify the mechanical behavior of the gel. Based on the model, the value of stored strain energy and the ratio of stiffness in the stretching directions were calculated at prescribed strains for each gel, and statistical comparisons were made among the gels cultured under the various mechanical constraints. Results showed that gels cultured under the free-floating and equibiaxial stretching conditions exhibited a nearly isotropic mechanical behavior, while gels cultured under the strip-biaxial and uniaxial stretching conditions developed a significant degree of mechanical anisotropy. In particular, gels cultured under the equibiaxial stretching condition with a greater stretch ratio appeared to be stiffer than those with a smaller stretch ratio. Also, a decellularized gel was stiffer than its non-decellularized counterpart. Finally, the retained mechanical anisotropy in gels cultured under the strip-biaxial stretching and uniaxial stretching conditions after cell removal reflected an irreversible matrix remodeling.

authors

Hu JJ,Liu YC,Chen GW,Wang MX,Lee PY

doi

10.1007/s10237-012-0448-x

subject

Has Abstract

pub_date

2013-10-01 00:00:00

pages

849-68

issue

5

eissn

1617-7959

issn

1617-7940

journal_volume

12

pub_type

杂志文章
  • Time-dependent behavior of cartilage surrounding a metal implant for full-thickness cartilage defects of various sizes: a finite element study.

    abstract::Recently, physiological and biomechanical studies on animal models with metal implants filling full-thickness cartilage defects have resulted in good clinical outcomes. The knowledge of the time-dependent macroscopic behavior of cartilage surrounding the metal implant is essential for understanding the joint function ...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-011-0346-7

    authors: Manda K,Eriksson A

    更新日期:2012-05-01 00:00:00

  • Patient-specific predictions of aneurysm growth and remodeling in the ascending thoracic aorta using the homogenized constrained mixture model.

    abstract::In its permanent quest of mechanobiological homeostasis, our vasculature significantly adapts across multiple length and timescales in various physiological and pathological conditions. Computational modeling of vascular growth and remodeling (G&R) has significantly improved our insights into the mechanobiological pro...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01184-8

    authors: Mousavi SJ,Farzaneh S,Avril S

    更新日期:2019-12-01 00:00:00

  • A microfluidic device with spatiotemporal wall shear stress and ATP signals to investigate the intracellular calcium dynamics in vascular endothelial cells.

    abstract::Intracellular calcium dynamics plays an important role in the regulation of vascular endothelial cellular functions. In order to probe the intracellular calcium dynamic response under synergistic effect of wall shear stress (WSS) and adenosine triphosphate (ATP) signals, a novel microfluidic device, which provides the...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-018-1076-x

    authors: Chen ZZ,Yuan WM,Xiang C,Zeng DP,Liu B,Qin KR

    更新日期:2019-02-01 00:00:00

  • A growth-based model for the prediction of fiber angle distribution in the intervertebral disc annulus fibrosus.

    abstract::There is a growing interest in the development of patient-specific finite element models of the human lumbar spine for both the assessment of injury risk and the development of treatment strategies. A current challenge in implementing these models is that the outer annulus fibrosus of the disc is composed of concentri...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01150-4

    authors: Michalek AJ

    更新日期:2019-10-01 00:00:00

  • The mechanical behaviour of chondrocytes predicted with a micro-structural model of articular cartilage.

    abstract::The integrity of articular cartilage depends on the proper functioning and mechanical stimulation of chondrocytes, the cells that synthesize extracellular matrix and maintain tissue health. The biosynthetic activity of chondrocytes is influenced by genetic factors, environmental influences, extracellular matrix compos...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-006-0016-3

    authors: Han SK,Federico S,Grillo A,Giaquinta G,Herzog W

    更新日期:2007-04-01 00:00:00

  • Homogenized stiffness matrices for mineralized collagen fibrils and lamellar bone using unit cell finite element models.

    abstract::Mineralized collagen fibrils have been usually analyzed like a two-phase composite material where crystals are considered as platelets that constitute the reinforcement phase. Different models have been used to describe the elastic behavior of the material. In this work, it is shown that when Halpin-Tsai equations are...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-013-0507-y

    authors: Vercher A,Giner E,Arango C,Tarancón JE,Fuenmayor FJ

    更新日期:2014-04-01 00:00:00

  • The combined impact of tissue heterogeneity and fixed charge for models of cartilage: the one-dimensional biphasic swelling model revisited.

    abstract::Articular cartilage is a complex, anisotropic, stratified tissue with remarkable resilience and mechanical properties. It has been subject to extensive modelling as a multiphase medium, with many recent studies examining the impact of increasing detail in the representation of this tissue's fine scale structure. Howev...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01123-7

    authors: Klika V,Whiteley JP,Brown CP,Gaffney EA

    更新日期:2019-08-01 00:00:00

  • A novel method for non-invasively detecting the severity and location of aortic aneurysms.

    abstract::The influence of an aortic aneurysm on blood flow waveforms is well established, but how to exploit this link for diagnostic purposes still remains challenging. This work uses a combination of experimental and computational modelling to study how aneurysms of various size affect the waveforms. Experimental studies are...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-017-0884-8

    authors: Sazonov I,Khir AW,Hacham WS,Boileau E,Carson JM,van Loon R,Ferguson C,Nithiarasu P

    更新日期:2017-08-01 00:00:00

  • Simulated tissue growth for 3D printed scaffolds.

    abstract::Experiments have demonstrated biological tissues grow by mechanically sensing their localized curvature, therefore making geometry a key consideration for tissue scaffold design. We developed a simulation approach for modeling tissue growth on beam-based geometries of repeating unit cells, with four lattice topologies...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-018-1040-9

    authors: Egan PF,Shea KA,Ferguson SJ

    更新日期:2018-10-01 00:00:00

  • Effect of left atrial ligation-driven altered inflow hemodynamics on embryonic heart development: clues for prenatal progression of hypoplastic left heart syndrome.

    abstract::Congenital heart defects (CHDs) are abnormalities in the heart structure present at birth. One important condition is hypoplastic left heart syndrome (HLHS) where severely underdeveloped left ventricle (LV) cannot support systemic circulation. HLHS usually initiates as localized tissue malformations with no underlying...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-020-01413-5

    authors: Salman HE,Alser M,Shekhar A,Gould RA,Benslimane FM,Butcher JT,Yalcin HC

    更新日期:2021-01-22 00:00:00

  • Pointwise characterization of the elastic properties of planar soft tissues: application to ascending thoracic aneurysms.

    abstract::In this manuscript, we present a combined experimental and computational technique that can identify the heterogeneous elastic properties of planar soft tissues. By combining inverse membrane analysis, digital image correlation, and bulge inflation tests, we are able to identify a tissue's mechanical properties locall...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-014-0646-9

    authors: Davis FM,Luo Y,Avril S,Duprey A,Lu J

    更新日期:2015-10-01 00:00:00

  • A coupled model of neovessel growth and matrix mechanics describes and predicts angiogenesis in vitro.

    abstract::During angiogenesis, sprouting microvessels interact with the extracellular matrix (ECM) by degrading and reorganizing the matrix, applying traction forces, and producing deformation. Morphometric features of the resulting microvascular network are affected by the interaction between the matrix and angiogenic microves...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-014-0635-z

    authors: Edgar LT,Maas SA,Guilkey JE,Weiss JA

    更新日期:2015-08-01 00:00:00

  • Injury risk prediction from computational simulations of ocular blast loading.

    abstract::A predictive Lagrangian-Eulerian finite element eye model was used to analyze 2.27 and 0.45 kg trinitrotoluene equivalent blasts detonated from 24 different locations. Free air and ground level blasts were simulated directly in front of the eye and at lateral offset locations with box, average, less protective, and mo...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-016-0830-1

    authors: Weaver AA,Stitzel SM,Stitzel JD

    更新日期:2017-04-01 00:00:00

  • Deformation of human red blood cells in extensional flow through a hyperbolic contraction.

    abstract::Flow-induced damage to red blood cells has been an issue of considerable importance since the introduction of the first cardiovascular devices. Early blood damage prediction models were based on measurements of damage by shear stress only. Subsequently, these models were extrapolated to include other components of the...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01208-3

    authors: Faghih MM,Sharp MK

    更新日期:2020-02-01 00:00:00

  • Effects of pH on transport properties of articular cartilages.

    abstract::Articular cartilages swell and shrink depending on the ionic strength of the electrolyte they are in contact with. This electro-chemo-mechanical coupling is due to the presence of fixed electrical charges on proteoglycans (PGs). In addition, at nonphysiological pH, collagen fibers become charged. Therefore, variation ...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-009-0158-1

    authors: Loret B,Simões FM

    更新日期:2010-02-01 00:00:00

  • Material model of pelvic bone based on modal analysis: a study on the composite bone.

    abstract::Digital models based on finite element (FE) analysis are widely used in orthopaedics to predict the stress or strain in the bone due to bone-implant interaction. The usability of the model depends strongly on the bone material description. The material model that is most commonly used is based on a constant Young's mo...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-016-0822-1

    authors: Henyš P,Čapek L

    更新日期:2017-02-01 00:00:00

  • Statistical shape modelling of the first carpometacarpal joint reveals high variation in morphology.

    abstract::The first carpometacarpal (CMC) joint, located at the base of the thumb and formed by the junction between the first metacarpal and trapezium, is a common site for osteoarthritis of the hand. The shape of both the first metacarpal and trapezium contributes to the intrinsic bony stability of the joint, and variability ...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01257-8

    authors: Rusli WMR,Kedgley AE

    更新日期:2020-08-01 00:00:00

  • Impact of calcifications on patient-specific wall stress analysis of abdominal aortic aneurysms.

    abstract::As a degenerative and inflammatory desease of elderly patients, about 80% of abdominal aortic aneurysms (AAA) show considerable wall calcification. Effect of calcifications on computational wall stress analyses of AAAs has been rarely treated in literature so far. Calcifications are heterogeneously distributed, non-fi...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-010-0191-0

    authors: Maier A,Gee MW,Reeps C,Eckstein HH,Wall WA

    更新日期:2010-10-01 00:00:00

  • Assessment of boundary conditions for CFD simulation in human carotid artery.

    abstract::Computational fluid dynamics (CFD) is an increasingly used method for investigation of hemodynamic parameters and their alterations under pathological conditions, which are important indicators for diagnosis of cardiovascular disease. In hemodynamic simulation models, the employment of appropriate boundary conditions ...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-018-1045-4

    authors: Xu P,Liu X,Zhang H,Ghista D,Zhang D,Shi C,Huang W

    更新日期:2018-12-01 00:00:00

  • A computational thrombus formation model: application to an idealized two-dimensional aneurysm treated with bare metal coils.

    abstract::Cardiovascular implantable devices alter the biofluid dynamics and biochemistry of the blood in which they are placed. These perturbations can lead to thrombus formation which may or may not be desired, depending on the application. In this work, a computational model is developed that couples biofluid dynamics and bi...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-018-1059-y

    authors: Horn JD,Maitland DJ,Hartman J,Ortega JM

    更新日期:2018-12-01 00:00:00

  • A mechanical model of posterior vitreous detachment and generation of vitreoretinal tractions.

    abstract::We propose a mechanical model of generation of vitreoretinal tractions in the presence of posterior vitreous detachment (PVD). PVD is a common occurrence with aging, and it consists in the separation of the vitreous body from the retina at the back pole of the eye, due to progressive shrinking of the vitreous gel. Dur...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-020-01360-1

    authors: Di Michele F,Tatone A,Romano MR,Repetto R

    更新日期:2020-12-01 00:00:00

  • A computational model that predicts reverse growth in response to mechanical unloading.

    abstract::Ventricular growth is widely considered to be an important feature in the adverse progression of heart diseases, whereas reverse ventricular growth (or reverse remodeling) is often considered to be a favorable response to clinical intervention. In recent years, a number of theoretical models have been proposed to mode...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-014-0598-0

    authors: Lee LC,Genet M,Acevedo-Bolton G,Ordovas K,Guccione JM,Kuhl E

    更新日期:2015-04-01 00:00:00

  • A model for arterial adaptation combining microstructural collagen remodeling and 3D tissue growth.

    abstract::Long-term adaptation of soft tissues is realized through growth and remodeling (G&R). Mathematical models are powerful tools in testing hypotheses on G&R and supporting the design and interpretation of experiments. Most theoretical G&R studies concentrate on description of either growth or remodeling. Our model combin...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-010-0204-z

    authors: Machyshyn IM,Bovendeerd PH,van de Ven AA,Rongen PM,van de Vosse FN

    更新日期:2010-12-01 00:00:00

  • A network-based response feature matrix as a brain injury metric.

    abstract::Conventional brain injury metrics are scalars that treat the whole head/brain as a single unit but do not characterize the distribution of brain responses. Here, we establish a network-based "response feature matrix" to characterize the magnitude and distribution of impact-induced brain strains. The network nodes and ...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-019-01261-y

    authors: Wu S,Zhao W,Rowson B,Rowson S,Ji S

    更新日期:2020-06-01 00:00:00

  • Tracking of fluorescence nanoparticles with nanometre resolution in a biological system: assessing local viscosity and microrheology.

    abstract::The aim of the study was to establish a user-friendly approach for single fluorescence particle 3D localization and tracking with nanometre precision in a standard fluorescence microscope using a point spread function (PSF) approach, and to evaluate validity and precision for different analysis methods and optical con...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-013-0499-7

    authors: Marki A,Ermilov E,Zakrzewicz A,Koller A,Secomb TW,Pries AR

    更新日期:2014-04-01 00:00:00

  • Sensitivity analysis and parametric study of elastic properties of an unidirectional mineralized bone fibril-array using mean field methods.

    abstract::The key parameters determining the elastic properties of an unidirectional mineralized bone fibril-array decomposed in two further hierarchical levels are investigated using mean field methods. Modeling of the elastic properties of mineralized micro- and nanostructures requires accurate information about the underlyin...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-010-0190-1

    authors: Reisinger AG,Pahr DH,Zysset PK

    更新日期:2010-10-01 00:00:00

  • In vivo estimation of elastic heterogeneity in an infarcted human heart.

    abstract::In myocardial infarction, muscle tissue of the heart is damaged as a result of ceased or severely impaired blood flow. Survivors have an increased risk of further complications, possibly leading to heart failure. Material properties play an important role in determining post-infarction outcome. Due to spatial variatio...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-018-1028-5

    authors: Balaban G,Finsberg H,Funke S,Håland TF,Hopp E,Sundnes J,Wall S,Rognes ME

    更新日期:2018-10-01 00:00:00

  • A two-muscle, continuum-mechanical forward simulation of the upper limb.

    abstract::By following the common definition of forward-dynamics simulations, i.e. predicting movement based on (neural) muscle activity, this work describes, for the first time, a forward-dynamics simulation framework of a musculoskeletal system, in which all components are represented as continuous, three-dimensional, volumet...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-016-0850-x

    authors: Röhrle O,Sprenger M,Schmitt S

    更新日期:2017-06-01 00:00:00

  • An integrated inverse model-experimental approach to determine soft tissue three-dimensional constitutive parameters: application to post-infarcted myocardium.

    abstract::Knowledge of the complete three-dimensional (3D) mechanical behavior of soft tissues is essential in understanding their pathophysiology and in developing novel therapies. Despite significant progress made in experimentation and modeling, a complete approach for the full characterization of soft tissue 3D behavior rem...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-017-0943-1

    authors: Avazmohammadi R,Li DS,Leahy T,Shih E,Soares JS,Gorman JH,Gorman RC,Sacks MS

    更新日期:2018-02-01 00:00:00

  • Dynamic modeling for shear stress induced ATP release from vascular endothelial cells.

    abstract::A dynamic model is proposed for shear stress induced adenosine triphosphate (ATP) release from endothelial cells (ECs). The dynamic behavior of the ATP/ADP concentration at the endothelial surface by viscous shear flow is investigated through simulation studies based on the dynamic ATP release model. The numerical res...

    journal_title:Biomechanics and modeling in mechanobiology

    pub_type: 杂志文章

    doi:10.1007/s10237-007-0088-8

    authors: Qin KR,Xiang C,Xu Z,Cao LL,Ge SS,Jiang ZL

    更新日期:2008-10-01 00:00:00