Abstract:
:The aim was to evaluate the effect of different zirconia discontinuous fiber fractions on radiopacity and other selected properties of glass discontinuous fiber-reinforced flowable composite (Exp-SFRC). Exp-SFRC was prepared by mixing 30 wt% of resin-matrix and 45 wt% of particulate-fillers to 25 wt% of various weight-fractions of E-glass/zirconia discontinuous fiber-fillers (25:0, 20:5, 15:10, 10:15, 0:25 wt%). Flexural strength and fracture toughness were determined for each experimental material. Radiograph of each Exp-SFRC and aluminium step wedge were taken to determine the radiopacity. Degree of conversion and light-transmission were also measured. Scanning electron microscopy was used to evaluate the microstructure of the Exp-SFRC. Analysis of variance (ANOVA) revealed that fractions of E-glass/zirconia discontinuous fiber-fillers had significant effect (p<0.05) on radiopacity and other tested properties of the Exp-SFRCs. Replacing low fraction of E-glass fiber with zirconia fiber-fillers can increase the radiopacity of the fiber-reinforced composite without deteriorating the mechanical properties, although, degree of conversion was decreased.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Garoushi S,Vallittu P,Lassila Ldoi
10.4012/dmj.2018-102subject
Has Abstractpub_date
2019-03-31 00:00:00pages
196-202issue
2eissn
0287-4547issn
1881-1361journal_volume
38pub_type
杂志文章abstract::The purpose of this study was to evaluate the influence of heating, cast bonding, and subsequent polishing procedures on attractive force of magnetic attachments. Two magnetic attachment systems with keepers of different chemical compositions (Hicorexslim 3013, 447J1; Magfit EX400, AUM20) were employed. Keepers examin...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.393
更新日期:2007-05-01 00:00:00
abstract::The purpose of this study was to evaluate the effect of different polymerization cycles on the flexural strengths and microhardness of two denture base materials (Meliodent and Paladent). Heat-polymerized acrylic resin specimens (65.0 mm long×10.0 mm wide×2.5 mm in height) were prepared using different short and long ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2016-023
更新日期:2017-03-31 00:00:00
abstract::The effectiveness of a barbituric acid/copper (II) chloride initiator system in dentin was examined in terms of the effects of barbituric acid structures and dentin conditioners on bond strength. Curing times and tensile bond strengths to bovine dentin were measured for PMMA/MMA resins in conjunction with initiators c...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.14.221
更新日期:1995-12-01 00:00:00
abstract::We evaluated the effect of different curing strategies for universal adhesives on micro-tensile bond strength (μTBS) between resin cement and dentin and/or between resin cement and indirect resin composite. Flat coronal dentin surfaces and composite resin disks were pretreated with silane-containing universal adhesive...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-240
更新日期:2018-06-08 00:00:00
abstract::This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-303
更新日期:2014-01-01 00:00:00
abstract::This study aimed to evaluate the effect of sulfinic acid sodium salt interposition after acid and sodium hypochlorite treatment (NC treatment) on dentin bonding durability using a mild type one-step self-etching adhesive. Fifteen human third molars were randomly assigned into three experimental groups according to den...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-105
更新日期:2017-11-29 00:00:00
abstract::This study investigated the effect of a coating material containing S-PRG fillers on the demineralization of bovine enamel and dentin, by measuring changes in the transmitted ultrasonic velocity. Bovine enamel and dentin specimens with and without coating (n=6 for each condition) were cut into blocks, immersed in 0.1 ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-153
更新日期:2012-01-01 00:00:00
abstract::The objective of this study was to examine the effects of storage conditions on the flexural strengths of resin composite materials for CAD/CAM restorations. Seven commercially available resin composite CAD/CAM blanks were examined. Rectangular specimens (4.0×1.2×4.0 mm) of each material were trimmed from the blanks a...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2019-202
更新日期:2020-09-29 00:00:00
abstract::This study was designed to evaluate the cytotoxicity of four dentin bonding agents and the effects of an antioxidant addition. Group A: G-aenial Bond, Group B: Optibond All in One, Group C: Gluma Self Etch and Group D: Clearfil S(3) Bond were added to the medium using extract method. The cells were cultured with or wi...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-079
更新日期:2015-01-01 00:00:00
abstract::The cream type of denture adhesives after use cannot be easily removed from oral mucosa and have the potential risk to change the oral flora. The effects of the temperature-responsive hydrogel Pluronic F-127 (PF) on the complex viscosity of denture adhesives were evaluated. Carboxy methylcellulose (CMC) mass fractions...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-191
更新日期:2016-01-01 00:00:00
abstract::This study tested whether exhaled humid conditions would affect the adhesion of etch-and-rinse, two-step and one-step self-etch adhesive resins to enamel. Enamel surfaces of human maxillary anterior teeth (N=240, n=20) were exposed to four humid conditions (H1: 63-68%, H2: 73-78%, H3: 93-98%, H4: 36-45% RH) during bon...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-200
更新日期:2013-01-01 00:00:00
abstract::Chemical mechanical polishing (CMP) of cpTi (Ti) was carried out using two types of slurries, acidic and basic colloidal silica containing H2O2 up to 3 wt%, to obtain flat and mirror-polished surfaces without any contaminated and reacted layers. Polishing behavior and surface properties were investigated using AFM, EP...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.28.68
更新日期:2009-01-01 00:00:00
abstract::High-power light-curing units have emerged that reduce the time of procedures in dental clinical work. However, patients sometimes complain of pain during the polymerization of composite resin. In this experiment, we investigated how differences in light-curing mode affect the temperature rise during composite resin p...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2018-158
更新日期:2019-07-31 00:00:00
abstract::Cyclic torsional loading tests were carried out in the laboratory using various implant systems, in order to clarify differences between the systems in loosening of abutment screws. Six samples from six commercially available abutment systems were used, giving a total of 36 samples. Four of the systems used internal c...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-023
更新日期:2015-01-01 00:00:00
abstract::Application of a light-cured porcelain margin is a technique which has been developed recently. In this study, we compared the porcelain margin properties of the porcelain-light-cured resin matrix system and the traditional porcelain-water system, in terms of volumetric shrinkage, density, compressive strength, surfac...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.14.1
更新日期:1995-06-01 00:00:00
abstract::To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding gro...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.576
更新日期:2006-09-01 00:00:00
abstract::Using a scanning electron microscope (SEM) and an electron probe surface roughness analyzer (ERA), we conducted the in vivo study of the effect of various filler components on the wear of composite resins. Experimental light-cured composite resins were prepared employing three different filler components; -(1) Silica ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.13.36
更新日期:1994-06-01 00:00:00
abstract::The depths of calcium-ion incorporation into a commercially pure titanium and an experimental beta-type titanium alloy were determined using Auger electron spectroscopy. After the electrochemical deposition of apatite, new compositional gradients appeared in the profiles in which the Ca and P concentrations gradually ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.21.306
更新日期:2002-12-01 00:00:00
abstract::This study aimed to investigate the relationship between the radiopacity of an experimental light-cured composite resin and the amount and type of its radiopaque material: Ti, SrCO3, ZrO2, BaSO4, or Bi2O3. Radiopacity of each material was evaluated in terms of aluminum equivalent thickness using an aluminum step wedge...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.315
更新日期:2005-09-01 00:00:00
abstract::The purpose of this study was to investigate the effect of laser irradiation on the enamel surface spectroscopically. Polished bovine enamel surface was irradiated with an Er:YAG laser apparatus and chemically analyzed using X-ray photoelectron spectroscopy (XPS). XPS detected core electron peaks such as carbon (C 1s)...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.214
更新日期:2006-06-01 00:00:00
abstract::To evaluate the cytotoxicity of resin cements on dental pulp-derived cells (bDPCs), Bifix QM (BQM), Choice 2(C2), RelyX U200(RU200), Maxcem Elite(ME), and Multilink Automix(MA) were tested. The materials were incubated in DMEM for 72 h. A real-time cell analyzer was used to evaluate cell survival. The statistical anal...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-167
更新日期:2015-01-01 00:00:00
abstract::The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.15.212
更新日期:1996-12-01 00:00:00
abstract::The purpose of this study was to investigate the retention force of complete palate coverage and palate-less dentures made with three polymerization systems (DS system, SR-Ivocap system, microwave polymerization system) in vitro. The retention force between each denture and a polyurethane model by intervening artifici...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.19
更新日期:2004-03-01 00:00:00
abstract::The aim of this study was to investigate in how far the way the specimen is fixed to the testing device influences the micro-tensile bond strength of adhesives to dentin. Compared to a flat jig, a notched jig enables the specimen to be aligned easier and more accurately perpendicular to the interface, thereby concentr...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.694
更新日期:2007-09-01 00:00:00
abstract::Seven types of amide monomers, methacryloyl tyrosine amide (MTYA), p-methacryloxybenzamide (p-MBA), p-methacryloxybutoxybenzamide (p-MBBA), o-methacryloxybutoxybenzamide (o-MBBA), p-methacryloxybutoxy phenylpropionamide (p-MBPPA), 3,5-dimethacryloxybenzamide (3,5-DMBA), and 3,5-di (methacryloxybutoxy)benzamide (3,5-DM...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.10.165
更新日期:1991-12-01 00:00:00
abstract::The influence of a thin carbonate-containing hydroxyapatite (CA) coating to tetragonal zirconia polycrystal (TZP) on osteoblastlike cell response was investigated. TZP disks were subjected to blasting and acid etching. Thin CA coatings were deposited by the molecular precursor method (TZP-CA). Initial cell adhesion of...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-122
更新日期:2014-01-01 00:00:00
abstract::The relation between the bonding efficacy of the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated. The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized 0.5 M EDTA...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.8.76
更新日期:1989-06-01 00:00:00
abstract::Although titanium has been widely used in prosthetic appliances, such as cast removable partial denture frameworks, high quality castings are still difficult to obtain. This study proposes a new partition technique using a metal foil for improving castability of a two-chamber pressure casting unit. The metal foil was ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.19.307
更新日期:2000-09-01 00:00:00
abstract::This study evaluated the polymerization shrinkage, flexural and compressive properties of low-shrinkage resin composites. For the study, four methacrylate-based and one silorane-based resin composites were light cured using three different light-curing units (LCUs) and their polymerization shrinkage, flexural (strengt...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-126
更新日期:2014-01-01 00:00:00
abstract::The aim of the present study was to examine whether interconnected porous hydroxyapatite ceramics (IP-CHA) could be used as bone substitute for implant treatment in reconstructive surgery. We firstly assessed if surround of the titanium surface placed into granular or block-type IP-CHA can observe new bone formation i...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-169
更新日期:2013-01-01 00:00:00