Multi-purpose bonding performance of newly synthesized phosphonic acid monomers.

abstract：:Three commercially available porcelains bonded to titanium were evaluated to determine the weakest zone of the titanium-porcelain bonding structures. Tensile bond tests were performed for these specimens (NO, DU, and VI) and for Ni-Cr alloy-porcelain bonding samples that served as controls. The maximum bond strengths ...

journal_title：Dental materials journal

authors： Kannari Y,Endo K,Ida Y,Ochi M,Ohno H

更新日期：2014-01-01 00:00:00

abstract：:Previously, high temperature properties of the silver-palladium-copper-gold alloy were investigated. In this study, the thermal expansion percentage and coefficient, and high temperature strengths of ADAS Type 3 gold alloy were investigated up to the liquidus temperature. Furthermore, microstructural and compositional...

journal_title：Dental materials journal

authors： Nagasawa S,Yoshida T,Terashima N,Mizoguchi T,Yagasaki H,Kamijo K,Ito M,Platt JA,Oshida Y

更新日期：2004-06-01 00:00:00

abstract：:Sixteen alloys and five pure metals were used and the open circuit potentials (OCP) and the coupled potentials with titanium were measured in five kinds of solutions. All alloys and metals showed the maximum OCP in 1.3% lactic acid solution, and the minimum in 0.01% sodium sulfide solution. The coupled potential depen...

journal_title：Dental materials journal

authors： Nakayama M,Ando N

更新日期：2001-03-01 00:00:00

abstract：:To determine new developed light curing units with shorter curing times effects on microleakage and microhardness values for resin fissure sealants. Resin filled sealant (UltraSeal-XT), resin unfilled sealant (Delton Type-II) and ormocer-based sealant (Admira-Seal) were light cured with a quartz-tungsten-halogen (QTH)...

journal_title：Dental materials journal

authors： Bani M,Tirali RE

更新日期：2016-01-01 00:00:00

abstract：:The purposes of this study were to examine the shock absorption capability of addition-cured silicone denture relining materials and the bonding strength of addition-cured silicone denture relining materials and a commercial mouthguard material to determine its applicability to mouthguard adjustment. Two addition-cure...

journal_title：Dental materials journal

authors： Fukasawa S,Churei H,Chowdhury RU,Shirako T,Shahrin S,Shrestha A,Wada T,Uo M,Takahashi H,Ueno T

更新日期：2016-01-01 00:00:00

abstract：:The bonding efficacy of sclerotic dentin was determined by measuring the polymerization contraction gap width of a commercial light-activated resin composite in a cervical defect and by measuring the micro-Vicker's hardness at the dentin adhesive surface; morphological characteristics were observed using a scanning el...

journal_title：Dental materials journal

authors： Tani C,Itoh K,Hisamitsu H,Wakumoto S

更新日期：2001-12-01 00:00:00

abstract：:This study investigated the effect of a coating material containing S-PRG fillers on the demineralization of bovine enamel and dentin, by measuring changes in the transmitted ultrasonic velocity. Bovine enamel and dentin specimens with and without coating (n=6 for each condition) were cut into blocks, immersed in 0.1 ...

journal_title：Dental materials journal

authors： Murayama R,Furuichi T,Yokokawa M,Takahashi F,Kawamoto R,Takamizawa T,Kurokawa H,Miyazaki M

更新日期：2012-01-01 00:00:00

abstract：:The mechanical properties of polycarboxylate cements containing 20 mass% of four kinds of aluminoborate whiskers with different fiber lengths and diameters were evaluated. Bending strength of the cements increased with increase in fiber length, whereby the strength of the cement with the longest fiber was about two ti...

journal_title：Dental materials journal

authors： Kurata S,Umemoto K

更新日期：2008-07-01 00:00:00

abstract：:The objective was to compare bond strengths of adhesives with/without thermocycling and to analyze the micromorphology of resindentin interfaces. Flat dentin surfaces were prepared and divided into eight groups to bond with four etch-and-rinse adhesives (Optibond FL, Adper Scotchbond Multi-Purpose, Optibond Solo Plus,...

journal_title：Dental materials journal

authors： Sangwichit K,Kingkaew R,Pongprueksa P,Senawongse P

更新日期：2016-01-01 00:00:00

abstract：:The aim was to investigate the effect of simulated low-temperature degradation (s-LTD) and hydrothermal fatigue on the degradation of three ZrO(2)-based dental materials. Lava, IPS, and NanoZr discs were randomly assigned to (1) Control-Storage in distilled water at 37°C; (2) Aging at 134°C for 5 h (s-LTD); (3) Thermo...

journal_title：Dental materials journal

authors： Perdigão J,Pinto AM,Monteiro RC,Braz Fernandes FM,Laranjeira P,Veiga JP

更新日期：2012-01-01 00:00:00

abstract：:Adhesion promoting monomers for dental metals, 5-(4-vinylbenzyl)-2-thiobarbituric acid (5VS), 6- (4-vinylbenzyl-n-propyl) amino-1,3,5-triazine-2,4-dithione (VBATDT) and 9,10-epithiodecyl methacrylate (EP8MA), were synthesized and surface treatment agents were prepared by dissolving each monomer in ethanol or acetone. ...

journal_title：Dental materials journal

authors： Kadoma Y

更新日期：2003-09-01 00:00:00

abstract：:This study aimed to evaluate cyclic fatigue resistance and bending properties and torque/force generation of WaveOne Gold (WOG) Primary in comparison with WaveOne (WO) Primary and Reciproc (RE) R25. A cyclic fatigue test revealed that the WOG Primary took significantly longer time to fracture compared with the WO Prim...

journal_title：Dental materials journal

authors： Fangli T,Maki K,Kimura S,Nishijo M,Tokita D,Ebihara A,Okiji T

更新日期：2019-06-01 00:00:00

abstract：:Enamel and dentin particles were added to an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step adhesive to react for 30 s. After enamel and dentin reactants were analyzed using X-ray diffraction (XRD) and phosphorus-31 nuclear magnetic resonance ((31)P NMR) techniques, curve-fitting analys...

journal_title：Dental materials journal

authors： Yokota Y,Nishiyama N

更新日期：2015-01-01 00:00:00

abstract：:This study was designed to evaluate the cytotoxicity of four dentin bonding agents and the effects of an antioxidant addition. Group A: G-aenial Bond, Group B: Optibond All in One, Group C: Gluma Self Etch and Group D: Clearfil S(3) Bond were added to the medium using extract method. The cells were cultured with or wi...

journal_title：Dental materials journal

authors： Atalayin C,Armagan G,Konyalioglu S,Kemaloglu H,Tezel H,Ergucu Z,Keser A,Dagci T,Onal B

更新日期：2015-01-01 00:00:00

abstract：:This study investigated the effects of spherical silica fillers on the physical and mechanical properties of resin-modified glass-ionomer cement (RMGIC). Specimens were fabricated by mixing untreated (UF) or silanized (SF) spherical silica filler into the powder of a commercially prepared RMGIC. The original RMGIC and...

journal_title：Dental materials journal

authors： Tjandrawinata R,Irie M,Yoshida Y,Suzuki K

更新日期：2004-06-01 00:00:00

abstract：:The anti-suck-back ability of five new high-speed air turbine handpiece models was evaluated in this study. First, suck-back pressure with water displacement within a glass tube was measured. Next, under three different conditions, how many on-off times it takes before fluorescent stains became visible on a piece of g...

journal_title：Dental materials journal

authors： Ozawa T,Nakano M,Arai T

更新日期：2010-11-01 00:00:00

abstract：:To evaluate the cytotoxicity of resin cements on dental pulp-derived cells (bDPCs), Bifix QM (BQM), Choice 2(C2), RelyX U200(RU200), Maxcem Elite(ME), and Multilink Automix(MA) were tested. The materials were incubated in DMEM for 72 h. A real-time cell analyzer was used to evaluate cell survival. The statistical anal...

journal_title：Dental materials journal

authors： Arslan Malkoç M,Demir N,Şengün A,Bozkurt ŞB,Hakki SS

更新日期：2015-01-01 00:00:00

abstract：:This study sought to evaluate the effects of different staining solutions on the colour stability of nanocomposites compared with microhybrid resin and to evaluate the degree of conversion of these two materials. Two different shades of two different composites were cured in polytetraflouroethylene disk rings. Coffee,...

journal_title：Dental materials journal

authors： Al Kheraif AA,Qasim SS,Ramakrishnaiah R,Ihtesham ur Rehman

更新日期：2013-01-01 00:00:00

abstract：:We investigated the adsorption of lipoteichoic acid (LTA) on titanium surfaces by using the quartz crystal microbalance (QCM) method, and confirmed the influence of mucin (MUC) pre-adsorption on LTA adsorption. Two injection methods were evaluated. Namely, Method A: single-step injection of LTA solution to the Ti sens...

journal_title：Dental materials journal

authors： Yoshida E,Hayakawa T

更新日期：2020-12-03 00:00:00

abstract：:The aim of this study was to evaluate the bond strength of three adhesive systems: Excite™, Adper Prompt L-Pop™ and AdheSE One™ to varying degrees of fluorotic enamel using micro-tensile bond strength (μTBS) tests. Human enamel was classified according to the Thylstrup and Fejerskov Index. The interface resin-enamel w...

journal_title：Dental materials journal

authors： Torres-Gallegos I,A Martinez-Castañon G,Loyola-Rodriguez JP,Patiño-Marin N,Encinas A,Ruiz F,Anusavice K

更新日期：2012-01-01 00:00:00

abstract：:This study investigated the changes in hardness and Young's modulus of the transparent layer of dentin associated with aging and the carious process. Eighteen extracted human molars with or without coronal caries were used in this study. The normal teeth were divided into two groups by age, and the carious teeth were ...

journal_title：Dental materials journal

authors： Zheng L,Nakajima M,Higashi T,Foxton RM,Tagami J

更新日期：2005-12-01 00:00:00

abstract：:This study evaluated the effect of different adhesive protocols on the shear bond strength (SBS) of bulk-fill resin composite repaired with bulk-fill or conventional composite. Cylindrical bulk-fill resin composite specimens were prepared and allocated into groups according to the bonding strategy: no treatment, Silan...

journal_title：Dental materials journal

authors： Cuevas-Suárez CE,Nakanishi L,Isolan CP,Ribeiro JS,Moreira AG,Piva E

更新日期：2020-03-31 00:00:00

abstract：:The microstructure and homogeneity of three commercial dentin and incisal unfired porcelain frits (one conventional and two ultra-low fusing types, fused-to metal were analyzed by X-ray diffractometry, scanning electron microspectroscopy, and wavelength- and energy dispersive X-ray microspectroscopy. The average conte...

journal_title：Dental materials journal

authors： Ban S,Matsuo K,Mizutani N,Iwase H,Kani T,Hasegawa J

更新日期：1998-12-01 00:00:00

abstract：:To improve the bioactivity of titanium surfaces, glow discharge was used to facilitate collagen grafting on titanium disks. Titanium test specimens were pre-treated by glow discharge fed with a mixture of argon and allylamine (AA) gases. Treated titanium disks were then grafted with type I collagen using glutaraldehyd...

journal_title：Dental materials journal

authors： Chang WJ,Ou KL,Lee SY,Chen JY,Abiko Y,Lin CT,Huang HM

更新日期：2008-05-01 00:00:00

abstract：:The objective of this work was to determine the antimicrobial and antibiofilm properties of mineral trioxide aggregate (MTA) supplemented with bismuth lipophilic nanoparticles (BisBAL NPs). The antimicrobial activity of the composite MTA-BisBAL NPs was determined by the disk diffusion assay, while antibiofilm activity...

journal_title：Dental materials journal

authors： Hernandez-Delgadillo R,Del Angel-Mosqueda C,Solís-Soto JM,Munguia-Moreno S,Pineda-Aguilar N,Sánchez-Nájera RI,Chellam S,Cabral-Romero C

更新日期：2017-07-26 00:00:00

abstract：:This study evaluated the effect of resin coating (COA) on dentin bond strength (BS) of five resin cements (RC). Ten groups were tested, according to RC and COA combinations. RCs were applied onto prepolymerized resin discs, which were bonded to dentin surfaces. Teeth were stored in water for 24 h, subjected to 5,000 t...

journal_title：Dental materials journal

authors： Giannini M,Takagaki T,Bacelar-Sá R,Vermelho PM,Ambrosano GM,Sadr A,Nikaido T,Tagami J

更新日期：2015-01-01 00:00:00

abstract：:This study aimed to investigate the in vitro biological response of human dental pulp cells to glass ionomer cement (GIC, Fuji IX GP(®)) containing 2.5% magnesium carbonate apatite (MgCO(3)Ap). MgCO(3)Ap was synthesized by wet method and characterized using FT-IR, XPS, and SEM. Fuji IX GP(®) served as a control. Test ...

journal_title：Dental materials journal

authors： Laiteerapong A,Lochaiwatana Y,Hirata I,Okazaki M,Mori K,Murakami S,Poolthong S

更新日期：2012-01-01 00:00:00

abstract：:The aim of the present study was to examine whether interconnected porous hydroxyapatite ceramics (IP-CHA) could be used as bone substitute for implant treatment in reconstructive surgery. We firstly assessed if surround of the titanium surface placed into granular or block-type IP-CHA can observe new bone formation i...

journal_title：Dental materials journal

authors： Minami M,Takechi M,Ohta K,Ohta A,Ninomiya Y,Takamoto M,Fukui A,Tada M,Kamata N

更新日期：2013-01-01 00:00:00

abstract：:Resin coating materials have been used for composite resin or provisional restoration in order to prevent plaque accumulation on their surfaces. However, it is not clear whether the coating materials influence attachment of periodontal bacteria. Therefore, we investigated the effect of resin coating materials on the a...

journal_title：Dental materials journal

authors： Kumada A,Matsuka Y,Mine A,Ono M,Uehara J,Sonoi N,Ito T,Takashiba S,Kuboki T

更新日期：2012-02-03 00:00:00

abstract：:Ag-Pd-Cu-Au alloy was subjected to a Thermo-Mechanical Analyzer to investigate high temperature properties up to its liquidus temperature. Microstructural examination and elemental analysis with EPMA were also conducted in the solid/liquid mixture region. The following conclusions were obtained. (1) The solidus temper...

journal_title：Dental materials journal

authors： Nagasawa S,Yoshida T,Mizoguchi T,Terashima N,Ito M,Platt JA,Oshida Y

更新日期：2003-09-01 00:00:00