Abstract:
:Previously, high temperature properties of the silver-palladium-copper-gold alloy were investigated. In this study, the thermal expansion percentage and coefficient, and high temperature strengths of ADAS Type 3 gold alloy were investigated up to the liquidus temperature. Furthermore, microstructural and compositional changes in the solid/liquid dual phase were studied. The following conclusions were obtained. (1) The solidus point of the Type 3 gold alloy was 899.3+/-11.7 degrees C, and the liquidus point was 962.3+/-2.4 degrees C. (2) The thermal expansion percentage at the solidus point was 1.636+/-0.046%, while it was 4.853+/-0.213% for the liquidus point. The thermal expansion percentage of the melt was 3.217+/-0.257%. (3) The melt expansion was observed even under the measuring pressure of 373.75 HPa, which was quite different from the fact that the melt expansion disappeared at the pressure of 20.87 HPa for the silver-palladium-copper-gold alloy. (4) The morphology of solid phase in the solid/liquid dual zone of this alloy was quite different from those observed with the silver-palladium-copper-gold alloy.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Nagasawa S,Yoshida T,Terashima N,Mizoguchi T,Yagasaki H,Kamijo K,Ito M,Platt JA,Oshida Ydoi
10.4012/dmj.23.81keywords:
subject
Has Abstractpub_date
2004-06-01 00:00:00pages
81-8issue
2eissn
0287-4547issn
1881-1361journal_volume
23pub_type
杂志文章abstract::This study aimed to evaluate the inhibitory effect of experimental pastes containing surface pre-reacted glass ionomer (S-PRG) fillers on enamel demineralization. Bovine blocks were treated twice a day for 4 days by 7 groups; experimental pastes containing 0-30 wt% S-PRG filler (S00, S01, S05, S10, and S30), deionized...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2016-303
更新日期:2017-07-26 00:00:00
abstract::The purpose of this study was to examine the antibacterial activity of composite resin with glass-ionomer filler particles versus that of contemporary commercial composite resins. Three composite resins were used: Beautifil II (containing S-PRG filler), Clearfil AP-X, and Filtek Z250. Resin blocks were bonded to maxil...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:10.4012/dmj.2009-050
更新日期:2010-03-01 00:00:00
abstract::The purpose of this study was to determine the optimal condition for fabricating accurate crowns efficiently using an internet-based CAD/CAM system. The influences of three different CAD/CAM restorative materials (titanium, porcelain, and composite resin) and three different step-over scanning distances (0.01 mm, 0.11...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.549
更新日期:2007-07-01 00:00:00
abstract::Although titanium has been widely used in prosthetic appliances, such as cast removable partial denture frameworks, high quality castings are still difficult to obtain. This study proposes a new partition technique using a metal foil for improving castability of a two-chamber pressure casting unit. The metal foil was ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.19.307
更新日期:2000-09-01 00:00:00
abstract::This study evaluated the effect of resin coating (COA) on dentin bond strength (BS) of five resin cements (RC). Ten groups were tested, according to RC and COA combinations. RCs were applied onto prepolymerized resin discs, which were bonded to dentin surfaces. Teeth were stored in water for 24 h, subjected to 5,000 t...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-099
更新日期:2015-01-01 00:00:00
abstract::This in vitro study aimed to evaluate the effect of two different polymer-based CAD/CAM materials; resin-nano ceramic (Lava Ultimate [LVU]) and composite (CERASMART [CS]), their different surface pre-treatments, and use of different resin cements on the µTBS of adhesively bonded CAD/CAM onlays to dentin. CAD/CAM mater...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-442
更新日期:2019-02-08 00:00:00
abstract::This study evaluated a new enzyme solution (SFC-V) for dentin caries removal, and obtained results were compared with Carisolv. Both solutions were used with a prototype plastic instrument - this being a modified technique for Carisolv. Five carious deciduous teeth were sectioned, and both treatments were applied alte...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.675
更新日期:2006-12-01 00:00:00
abstract::This study evaluated the effects of ceramic surface treatment agents on shear bond strengths to ceramic materials with and without thermocycling. Ceramic plates were prepared from feldspathic ceramic; AAA, lithium disilicate ceramic material; IPS e.max Press, zirconia ceramic; Lava. Ceramic surfaces were pretreated wi...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2016-383
更新日期:2017-11-29 00:00:00
abstract::This study investigated the durability, especially the nonwaterdegradable qualities, of experimental light-cured composite resin containing barium-borosilicate glass filler. For this purpose, Bis-GMA, a typical component of base monomer in conventional composite resin, was replaced by Bis-GMA-F which is water-repellen...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.12.1
更新日期:1993-06-01 00:00:00
abstract::Different types of calcium phosphate compounds are commercially available for medical and dental applications as bone substitute materials. Biological apatites contain several kinds of minor elements such as carbonate (CO3), magnesium (Mg), and fluoride (F) in enamel, dentin, and bone. It has been shown that F ion and...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.398
更新日期:2005-09-01 00:00:00
abstract::The purposes of this study were to examine the shock absorption capability of addition-cured silicone denture relining materials and the bonding strength of addition-cured silicone denture relining materials and a commercial mouthguard material to determine its applicability to mouthguard adjustment. Two addition-cure...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-378
更新日期:2016-01-01 00:00:00
abstract::The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.15.212
更新日期:1996-12-01 00:00:00
abstract::The aim of this study was to investigate the diffusion of red-stained experimental GM primer and blue-stained dentin bonding agent into EDTA-conditioned dentin and the effect of GM priming on contraction gap formation. After GM priming at 0, 35, 70, or 100 vol%, marginal adaptation was evaluated by measuring the wall-...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2009-084
更新日期:2010-10-01 00:00:00
abstract::Photocatalytic activity from the reaction of titanium oxide with ultraviolet light has recently gained much attention. In particular, there is scientific interest in inducing photocatalytic reactions on Ti-Ni alloy, a material widely used in orthodontic applications. However, it is believed that inducing a photocataly...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.26.924
更新日期:2007-11-01 00:00:00
abstract::The mechanical properties of polycarboxylate cements containing 20 mass% of four kinds of aluminoborate whiskers with different fiber lengths and diameters were evaluated. Bending strength of the cements increased with increase in fiber length, whereby the strength of the cement with the longest fiber was about two ti...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.561
更新日期:2008-07-01 00:00:00
abstract::Surface replication is a nondestructive evaluation technique applied in examining surfaces' cracks/wear. This is quite valuable when the surface of interest cannot be further manipulated by cutting or polishing to fit directly under a microscope. Replication by acetate sheets is one of the techniques applied in indust...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-444
更新日期:2019-02-08 00:00:00
abstract::This study investigated the changes in hardness and Young's modulus of the transparent layer of dentin associated with aging and the carious process. Eighteen extracted human molars with or without coronal caries were used in this study. The normal teeth were divided into two groups by age, and the carious teeth were ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.648
更新日期:2005-12-01 00:00:00
abstract::This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-303
更新日期:2014-01-01 00:00:00
abstract::The effects of dissolved-oxygen concentration and fluoride concentration on the corrosion behaviors of commercial pure titanium, Ti-6Al-4V and Ti-6Al-7Nb alloys and experimentally produced Ti-0.2Pd and Ti-0.5Pt alloys were examined using the corrosion potential measurements. The amount of dissolved Ti was analyzed by ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.21.83
更新日期:2002-06-01 00:00:00
abstract::The influence of a thin carbonate-containing hydroxyapatite (CA) coating to tetragonal zirconia polycrystal (TZP) on osteoblastlike cell response was investigated. TZP disks were subjected to blasting and acid etching. Thin CA coatings were deposited by the molecular precursor method (TZP-CA). Initial cell adhesion of...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-122
更新日期:2014-01-01 00:00:00
abstract::The aim of this study was to evaluate temperature changes in the pulp chamber during polymerization of four different pulp-capping materials using a LED-light-curing-unit in the contact and noncontact positions. A pulpal circulation mechanism was simulated to measure increases in temperature in four pulp-capping mater...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-274
更新日期:2014-01-01 00:00:00
abstract::Sixteen alloys and five pure metals were used and the open circuit potentials (OCP) and the coupled potentials with titanium were measured in five kinds of solutions. All alloys and metals showed the maximum OCP in 1.3% lactic acid solution, and the minimum in 0.01% sodium sulfide solution. The coupled potential depen...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.20.75
更新日期:2001-03-01 00:00:00
abstract::A zirconia-binding peptide motif was identified using a peptide phage display system. Yttria stabilized zirconia beads and discs were used as the target. Quartz crystal microbalance was used to monitor the binding of phages to zirconia. Starting from a library of phages displaying random sequences of 12-mer peptides, ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-161
更新日期:2011-01-01 00:00:00
abstract::The aim of the present study was to measure various mechanical properties of acrylic denture base resins, including flexural modulus, flexural strength, fracture toughness, Barcol and Vickers hardness and their related properties, and to investigate correlations between different mechanical properties. Resin specimens...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-205
更新日期:2012-02-03 00:00:00
abstract::The objective of the study was to compare 1) the mean micro-shear bond strength and 2) failure mode of cements to metals in nonenclosed and mold-enclosed specimens. Specimens were prepared in mold-enclosed and non-enclosed formats from two RMGIC's and a self-adhesive resin-cement. 3-way ANOVA analysis and Tukey post h...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-065
更新日期:2013-01-01 00:00:00
abstract::The effect of acidic fluoride solution on NiTi arch wires was examined by testing crystal structure, tensile strength, morphology after fracture, and element release from wire under four different test solutions after 1 or 3 d immersion. Three-day immersion in a 0.2%/pH 4 solution did not form any new crystal structur...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.557
更新日期:2004-12-01 00:00:00
abstract::Temperature dependencies of thermal expansion coefficients for the alloys of Pd-Ag, Pd-Cu and Pd-Co binary systems were measured at temperatures up to 900 degrees C, with heating and cooling rates of 5 degrees C/min. The coefficient of thermal expansion of alloys with no transformation in the temperature range of inte...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.9.47
更新日期:1990-06-01 00:00:00
abstract::The objective of this study was to clarify the effect of surface topography on osteoblast-like cell behavior on yttria stabilized tetragonal zirconia polycrystals (TZP). Mirror-polished; blasted with 50- or 150-µm alumina (SB50 and SB150); and SB150 acid-etched with hydrofluoric acid (SB150E) were prepared on TZP. Ini...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-208
更新日期:2013-01-01 00:00:00
abstract::The aim of this study was to clarify the effect of heating rate on the development of both transient and residual stresses in investment molds. Solid, cylindrical, gypsum-based molds were modeled and theoretical calculations made of temperature distributions with a constant heating rate. These calculations used experi...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.15.121
更新日期:1996-12-01 00:00:00
abstract::This study investigated the effect of a coating material containing S-PRG fillers on the demineralization of bovine enamel and dentin, by measuring changes in the transmitted ultrasonic velocity. Bovine enamel and dentin specimens with and without coating (n=6 for each condition) were cut into blocks, immersed in 0.1 ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-153
更新日期:2012-01-01 00:00:00