Abstract:
:This study evaluated a new enzyme solution (SFC-V) for dentin caries removal, and obtained results were compared with Carisolv. Both solutions were used with a prototype plastic instrument - this being a modified technique for Carisolv. Five carious deciduous teeth were sectioned, and both treatments were applied alternately to each half. Micro-CT observations showed that both treatments resulted in removal of the outer demineralized dentin layer: 28.6% for SFC-V and 28.2% for Carisolv. As for the remaining demineralized dentin, thicknesses of 0.27 microm (SFC-V) and 0.31microm (Carisolv) were observed with no statistically significant differences. FE-SEM analysis revealed that the use of Carisolv resulted in a rougher surface; whereas after SFC-V enzymatic treatment, an organized dentin collagen network with open tubules and few signs of bacteria were observed. In summary, the experimental enzymatic solution and the modified Carisolv treatment removed comparable amounts of carious dentin but with differing resultant surface morphologies.
journal_name
Dent Mater Jjournal_title
Dental materials journalauthors
Clementino-Luedemann TN,Dabanoglu A,Ilie N,Hickel R,Kunzelmann KHdoi
10.4012/dmj.25.675subject
Has Abstractpub_date
2006-12-01 00:00:00pages
675-83issue
4eissn
0287-4547issn
1881-1361journal_volume
25pub_type
杂志文章abstract::The bonding efficacy of sclerotic dentin was determined by measuring the polymerization contraction gap width of a commercial light-activated resin composite in a cervical defect and by measuring the micro-Vicker's hardness at the dentin adhesive surface; morphological characteristics were observed using a scanning el...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.20.359
更新日期:2001-12-01 00:00:00
abstract::This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...
journal_title:Dental materials journal
pub_type: 杂志文章,随机对照试验
doi:
更新日期:2011-01-01 00:00:00
abstract::In this study, wedge-shaped CP titanium castings and Ti-6Al-7Nb alloy castings were produced by three types of investment. The effects of the castings' thickness on surface reaction layer were investigated by measuring Vickers hardness, observing the microstructure, and analyzing the oxygen concentration. It was found...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.23.387
更新日期:2004-09-01 00:00:00
abstract::Seven types of amide monomers, methacryloyl tyrosine amide (MTYA), p-methacryloxybenzamide (p-MBA), p-methacryloxybutoxybenzamide (p-MBBA), o-methacryloxybutoxybenzamide (o-MBBA), p-methacryloxybutoxy phenylpropionamide (p-MBPPA), 3,5-dimethacryloxybenzamide (3,5-DMBA), and 3,5-di (methacryloxybutoxy)benzamide (3,5-DM...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.10.165
更新日期:1991-12-01 00:00:00
abstract::The purpose of this study was to evaluate the effect of various incremental filling techniques on adhesion between composite and cavity floor using light-cured resin composite. Black ABS resin and hybrid resin composite were used as mold materials--instead of dentin--for the preparation of cavities, and standardized t...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.25.503
更新日期:2006-09-01 00:00:00
abstract::Enamel and dentin particles were added to an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step adhesive to react for 30 s. After enamel and dentin reactants were analyzed using X-ray diffraction (XRD) and phosphorus-31 nuclear magnetic resonance ((31)P NMR) techniques, curve-fitting analys...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-260
更新日期:2015-01-01 00:00:00
abstract::The aim of this study was to evaluate temperature changes in the pulp chamber during polymerization of four different pulp-capping materials using a LED-light-curing-unit in the contact and noncontact positions. A pulpal circulation mechanism was simulated to measure increases in temperature in four pulp-capping mater...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-274
更新日期:2014-01-01 00:00:00
abstract::The effect of warm air-blowing on the sealing ability of two one-bottle and one two-bottle silane-containing universal adhesives (UAs) applied to lithium disilicate ceramics (LDS) was evaluated. Tapered cavities prefabricated in LDS blocks (IPS e.max CAD) were treated by the adhesives, air-blown either with normal air...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2020-057
更新日期:2020-10-24 00:00:00
abstract::The efficacy of four commercial and two experimental dentin bonding systems was examined by observing the cavity adaptation of commercial light-cured resin composites restored in the dogs scheduled to be sacrificed after a medical experiment. Before being sacrificed, a cylindrical class V cavity was prepared in each c...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.17.195
更新日期:1998-09-01 00:00:00
abstract::A zirconia-binding peptide motif was identified using a peptide phage display system. Yttria stabilized zirconia beads and discs were used as the target. Quartz crystal microbalance was used to monitor the binding of phages to zirconia. Starting from a library of phages displaying random sequences of 12-mer peptides, ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-161
更新日期:2011-01-01 00:00:00
abstract::This study investigated the effect of a coating material containing S-PRG fillers on the demineralization of bovine enamel and dentin, by measuring changes in the transmitted ultrasonic velocity. Bovine enamel and dentin specimens with and without coating (n=6 for each condition) were cut into blocks, immersed in 0.1 ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2012-153
更新日期:2012-01-01 00:00:00
abstract::This study evaluated the effects of combining enamel microabrasion and dental bleaching on the physical properties of enamel, using in vitro and in situ conditions and evaluating surface roughness, enamel microhardness and scanning electron microscopy images. One hundred sound bovine teeth were sectioned and cut into ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2014-334
更新日期:2016-01-01 00:00:00
abstract::This study investigated the changes in hardness and Young's modulus of the transparent layer of dentin associated with aging and the carious process. Eighteen extracted human molars with or without coronal caries were used in this study. The normal teeth were divided into two groups by age, and the carious teeth were ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.648
更新日期:2005-12-01 00:00:00
abstract::The aim of this study was to investigate the effect of three metal priming agents on the bond strength of adhesive resin cement to Silver-Zinc-Tin-Indium (Ag-Zn-Sn-In) alloy and pure Ag, Zn, Sn, and In. The specimens were air-abraded with alumina and then primed with one of three metal priming agents: V-Primer, Esteni...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-139
更新日期:2018-03-30 00:00:00
abstract::Different types of calcium phosphate compounds are commercially available for medical and dental applications as bone substitute materials. Biological apatites contain several kinds of minor elements such as carbonate (CO3), magnesium (Mg), and fluoride (F) in enamel, dentin, and bone. It has been shown that F ion and...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.398
更新日期:2005-09-01 00:00:00
abstract::Chemical mechanical polishing (CMP) of cpTi (Ti) was carried out using two types of slurries, acidic and basic colloidal silica containing H2O2 up to 3 wt%, to obtain flat and mirror-polished surfaces without any contaminated and reacted layers. Polishing behavior and surface properties were investigated using AFM, EP...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.28.68
更新日期:2009-01-01 00:00:00
abstract::This research was conducted to investigate the bond strength between artificial teeth and a thermoplastic denture base resin for injection molding with different surface preparations for use in flexible resin removable partial dentures. Composite resin denture teeth and acrylic denture resin teeth were bonded to three...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2020-183
更新日期:2021-01-15 00:00:00
abstract::To clarify the mechanical properties of fiber-reinforced hybrid resin bridges, this study evaluated the influence of various bonding agents ((Modeling Liquid (ML), DE Resin (DE), Bell Bond (BE), Mega Bond (MG), Durafil Bond (DU), Fluoro Bond (FB), Mac-Bond (MC), EG Bond (EG), Unifill Bond (UN), Single Bond (SN)) impre...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.723
更新日期:2008-09-01 00:00:00
abstract::The aim of this study was to evaluate the trial Teaching Robot for the development of a contact-type measuring apparatus for using directly in the oral cavity. A standard model was used to mimic the dentition by placing an arrangement of three bearing balls. The diameters of the balls were measured. A practical dentit...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.22.168
更新日期:2003-06-01 00:00:00
abstract::The biaxial flexural strength and cyclic fatigue biaxial flexural strength of CAD/CAM ceramics polished with #220, 400, 600 and 1000 diamond pads were measured in an effort to determine the effect of surface roughness on fatigue behavior of dental ceramics. The surface roughness was improved after polishing with a sma...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.18.395
更新日期:1999-12-01 00:00:00
abstract::The aim of this study was to estimate the flexural properties of three kinds of experimental fiber-reinforced composite (FRC) posts and to evaluate their potential use as posts. Experimental FRC posts were fabricated with glass, aramid, and UHMWP fibers. Commercial FRC posts were used for comparison. A three-point ben...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2010-053
更新日期:2011-01-01 00:00:00
abstract::The purpose of this study was to investigate the effect of remaining dentin thickness (RDT) and long term water storage on dentin bond strength in-vitro. Twenty-seven third molars were randomly divided into 3 groups: Clearfil Bond SE ONE (SE1, Kuraray Noritake Dental, Okayama, Japan), G-Bond plus (GB, GC, Tokyo, Japan...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-140
更新日期:2018-07-29 00:00:00
abstract::The purpose of the this study was to evaluate the cytotoxicity of dental resin monomers in the presence of a rat liver S9 mix containing cytochrome P 450 enzymes. JTC-12 cells derived from a monkey kidney were seeded on a 96-well multi-well-plate at 9 x 10(3) cells per well. After cultivation, the S9 mix was added to ...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.18.76
更新日期:1999-03-01 00:00:00
abstract::This study examined the ability of a photocatalyst mixed in a denture base resin to decompose organic substances which adhered to the denture base resin surface. The photocatalyst was mixed with denture base resin at concentrations of 0, 5, 10, and 15% (w/w). Decomposition test, bending test, and surface roughness mea...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.27.179
更新日期:2008-03-01 00:00:00
abstract::This study aimed to evaluate the effect of an acidic-adjusted pH of solvent in silanization on the amount of fluoride released and mechanical properties of heat-cured acrylic resin containing a silanized fluoride-releasing filler. The experimental groups were divided into 4 groups; non-silanized, acidic-adjusted pH, n...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2015-403
更新日期:2016-01-01 00:00:00
abstract::The purpose of this study was to evaluate, in vitro, the antimicrobial effect of iRoot BP, iRoot BP Plus, and mineral trioxide aggregate (MTA) against Entercoccus faecalis and Candida albicans by using direct contact test. The materials were tested immediately after application to the microtiter wells and after settin...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2013-250
更新日期:2014-01-01 00:00:00
abstract::The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casti...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.15.212
更新日期:1996-12-01 00:00:00
abstract::Surface replication is a nondestructive evaluation technique applied in examining surfaces' cracks/wear. This is quite valuable when the surface of interest cannot be further manipulated by cutting or polishing to fit directly under a microscope. Replication by acetate sheets is one of the techniques applied in indust...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2017-444
更新日期:2019-02-08 00:00:00
abstract::Effects of functionally gradient calcium phosphate consisting of hydroxyapatite (HAP) and alpha-tricalcium phosphate (alpha-TCP) on proliferation and differentiation of osteoblasts were evaluated using MC3T3-E1 cells. There were no significant differences in the proliferation of MC3T3-E1 cells among HAP-alpha-TCP func...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.24.207
更新日期:2005-06-01 00:00:00
abstract::The aim was to investigate the effect of simulated low-temperature degradation (s-LTD) and hydrothermal fatigue on the degradation of three ZrO(2)-based dental materials. Lava, IPS, and NanoZr discs were randomly assigned to (1) Control-Storage in distilled water at 37°C; (2) Aging at 134°C for 5 h (s-LTD); (3) Thermo...
journal_title:Dental materials journal
pub_type: 杂志文章
doi:10.4012/dmj.2011-216
更新日期:2012-01-01 00:00:00