当前位置： SCI文献检索 > Journal of the Mechanical Behavior of Biomedical Materials期刊下所有文献 > Dynamic nanomechanical properties of novel Si-rich intermetallic coatings growth on a medical 316 LVM steel by hot dipping in a hypereutectic Al-25Si alloy.

Dynamic nanomechanical properties of novel Si-rich intermetallic coatings growth on a medical 316 LVM steel by hot dipping in a hypereutectic Al-25Si alloy.

Abstract：

:This aim of this study is to determine the elastoplastic properties of Ni-free Al3FeSi2 intermetallic coatings grown on medical stainless steel under different experimental conditions. Elastoplastic properties are defined by the plasticity index (PI), which correlates the hardness and the Young's modulus. Special emphasis is devoted to correlate the PI with the wear resistance under sliding contact, determined by scratch testing, and fracture toughness, determined by using a novel method based on successive impacts with small loads. With regard to the substrate, the developed coatings are harder and exhibit a lower Young's reduced modulus, irrespective of the experimental conditions. It has been shown that preheating of the samples prior to hot dipping and immersion influences the type and volume fraction of precipitates, which in turn also affect the nanomechanical properties. The higher the preheating temperature is, the greater the Young's reduced modulus is. For a given preheating condition, an increase of the immersion time yields a decrease in hardness. Although apparent friction coefficients of coated specimens are smaller than those obtained on AISI 316 LVM, they increase when using preheating or higher immersion times during processing, which correlates with the PI. The presence of precipitates produces an increase in fracture toughness, with values greater than those presented by samples processed on melted AlSi alloys with lower Si content (12 wt%). Therefore, these intermetallic coatings could be considered "hard but tough", suitable to enhance the wear resistance, especially when using short periods of immersion.

journal_name

J Mech Behav Biomed Mater

journal_title

Journal of the mechanical behavior of biomedical materials

authors

Frutos E,González-Carrasco JL

doi

10.1016/j.jmbbm.2015.02.018

subject

Has Abstract

pub_date

2015-06-01 00:00:00

pages

93-103

eissn

1751-6161

issn

1878-0180

pii

S1751-6161(15)00061-2

journal_volume

46

pub_type

杂志文章

相关文献

Journal of the Mechanical Behavior of Biomedical Materials文献大全
  • Prediction of cross section fracture path of cortical bone through nanoindentation array.

    abstract：:Although great progresses in the fracture mechanisms and deformation behaviors of cortical bones have been achieved, the effective methods to predict the surface fracture path of cortical bones are still difficult. By using depth-sensing nanoindentation measurement technique, the hardness distribution map of cortical ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.104303

    authors： Ma Z,Qiang Z,Zeng K,Xiao J,Zhou L,Zu L,Zhao H,Ren L

    更新日期：2021-01-20 00:00:00

  • Comparison of endocrowns made of lithium disilicate glass-ceramic or polymer-infiltrated ceramic networks and direct composite resin restorations: fatigue performance and stress distribution.

    abstract：:This study compared the fatigue performance and the stress distribution of endodontically treated molars restored with endocrowns obtained with lithium disilicate glass-ceramic or a polymer-infiltrated ceramic network, both processed by CAD-CAM, and direct composite restorations. Forty-eight human mandibular molars we...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103401

    authors： Dartora G,Rocha Pereira GK,Varella de Carvalho R,Zucuni CP,Valandro LF,Cesar PF,Caldas RA,Bacchi A

    更新日期：2019-12-01 00:00:00

  • Microstructure and mechanical properties of open-cellular biomaterials prototypes for total knee replacement implants fabricated by electron beam melting.

    abstract：:Total knee replacement implants consisting of a Co-29Cr-6Mo alloy femoral component and a Ti-6Al-4V tibial component are the basis for the additive manufacturing of novel solid, mesh, and foam monoliths using electron beam melting (EBM). Ti-6Al-4V solid prototype microstructures were primarily α-phase acicular platele...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2011.05.010

    authors： Murr LE,Amato KN,Li SJ,Tian YX,Cheng XY,Gaytan SM,Martinez E,Shindo PW,Medina F,Wicker RB

    更新日期：2011-10-01 00:00:00

  • Calibration of colloidal probes with atomic force microscopy for micromechanical assessment.

    abstract：:Mechanical assessment of biological materials and tissue-engineered scaffolds is increasingly focusing at lower length scale levels. Amongst other techniques, atomic force microscopy (AFM) has gained popularity as an instrument to interrogate material properties, such as the indentation modulus, at the microscale via ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.05.026

    authors： Kain L,Andriotis OG,Gruber P,Frank M,Markovic M,Grech D,Nedelkovski V,Stolz M,Ovsianikov A,Thurner PJ

    更新日期：2018-09-01 00:00:00

  • Characterization, mechanical properties and corrosion resistance of biocompatible Zn-HA/TiO2 nanocomposite coatings.

    abstract：:Biocompatible Zinc-hydroxyapatite-titania and Zinc-hydroxyapatite nanocomposite coatings have been prepared by electrodeposition on NiTi shape memory alloy. Structures of coatings were characterized using X-ray diffraction (XRD). It was found that addition of TiO2 particles cause to reduction of crystallite size of co...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.05.016

    authors： Mirak M,Alizadeh M,Ghaffari M,Ashtiani MN

    更新日期：2016-09-01 00:00:00

  • Reduction of load-bearing capacity of all-ceramic crowns due to cement aging.

    abstract：:The purpose of this study was to investigate how water aging of the resin cement influences the stress distribution in all-ceramic crowns and if there is an increase in the propensity for crown failure. The failure of all-ceramic crowns attributed to cement degradation was explored using a combination of experimental ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2012.08.003

    authors： Lu C,Wang R,Mao S,Arola D,Zhang D

    更新日期：2013-01-01 00:00:00

  • Anisotropic electrospun honeycomb polycaprolactone scaffolds: Elaboration, morphological and mechanical properties.

    abstract：:Tissue engineering technology requires porous scaffolds, based on biomaterials, which have to mimic as closely as possible the morphological and anisotropic mechanical properties of the native tissue to substitute. Anisotropic fibrous scaffolds fabricated by template-assisted electrospinning are investigated in this s...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.104124

    authors： Mondésert H,Bossard F,Favier D

    更新日期：2021-01-01 00:00:00

  • Glycerol-dimethacrylate as alternative hydrophilic monomer for HEMA replacement in simplified adhesives.

    abstract：OBJECTIVES:Hydroxyethyl-methacrylate (HEMA) is still widely used in simplified adhesives. Indeed, several shortcomings occur with this monomer, such as water uptake and formation of linear polymers. This study aimed to compare the effects of HEMA replacement by glycerol-dimethacrylate (GDMA) on selected physicochemical...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.03.022

    authors： Araújo-Neto VG,Nobre CFA,De Paula DM,Souza LC,Silva JC,Moreira MM,Picanço PRB,Feitosa VP

    更新日期：2018-06-01 00:00:00

  • Within subject heterogeneity in tissue-level post-yield mechanical and material properties in human trabecular bone.

    abstract：:The ability to determine patient-specific mechanical properties of trabecular bone is needed for a reliable estimation of fracture risks. Tissue mechanics and material composition are important factors that contribute to trabecular bone performance, but only a few studies have investigated the post-yield behaviour of ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2013.04.014

    authors： Carretta R,Stüssi E,Müller R,Lorenzetti S

    更新日期：2013-08-01 00:00:00

  • Adaptive responses of murine osteoblasts subjected to coupled mechanical stimuli.

    abstract：:Restitution of the natural organization and orientation of cells is imperative for the construction of functional tissue scaffolds. While numerous studies have exploited mechanical methods to engineer tissues with the desired cellular architecture, fundamental knowledge is still lacking in understanding the manner in ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2017.09.018

    authors： Serrano JC,Cora-Cruz J,Diffoot-Carlo N,Sundaram PA

    更新日期：2018-01-01 00:00:00

  • Fatigue life of bovine meniscus under longitudinal and transverse tensile loading.

    abstract：:The knee meniscus is composed of a fibrous extracellular matrix that is subjected to large and repeated loads. Consequently, the meniscus is frequently torn, and a potential mechanism for failure is fatigue. The objective of this study was to measure the fatigue life of bovine meniscus when applying cyclic tensile loa...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.12.020

    authors： Creechley JJ,Krentz ME,Lujan TJ

    更新日期：2017-05-01 00:00:00

  • Evaluation of the mechanical properties of powder metallurgy Ti-6Al-7Nb alloy.

    abstract：:Titanium and its alloys are common biomedical materials owing to their combination of mechanical properties, corrosion resistance and biocompatibility. Powder metallurgy (PM) techniques can be used to fabricate biomaterials with tailored properties because changing the processing parameters, such as the sintering temp...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.12.005

    authors： Bolzoni L,Ruiz-Navas EM,Gordo E

    更新日期：2017-03-01 00:00:00

  • Mechanical behaviour of pressed and sintered titanium alloys obtained from master alloy addition powders.

    abstract：:The fabrication of the workhorse Ti-6Al-4V alloy and of the Ti-3Al-2.5V alloy was studied considering the master alloy addition variant of the blending elemental approach conventionally used for titanium powder metallurgy. The powders were characterised by means thermal analysis and X-ray diffraction and shaped by mea...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2012.05.019

    authors： Bolzoni L,Esteban PG,Ruiz-Navas EM,Gordo E

    更新日期：2012-11-01 00:00:00

  • An experimental study to investigate biomechanical aspects of the initial stability of press-fit implants.

    abstract：:Initial fixation of press-fit implants depends on interference fit, surface morphology, and bone material properties. To understand the biomechanical effect of each factor and their interactions, the pull-out strength of seven types of CoCrMo tapered implants, with four different interference fits, three different sur...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2014.11.014

    authors： Berahmani S,Janssen D,van Kessel S,Wolfson D,de Waal Malefijt M,Buma P,Verdonschot N

    更新日期：2015-02-01 00:00:00

  • Clinical versus pre-clinical FE models for vertebral body strength predictions.

    abstract：:The finite element analysis is an accepted method to predict vertebral body compressive strength. This study compares measurements obtained from in vitro tests with the ones from two different simulation models: clinical quantitative computer tomography (QCT) based homogenized finite element (hFE) models and pre-clini...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2012.11.018

    authors： Pahr DH,Schwiedrzik J,Dall'Ara E,Zysset PK

    更新日期：2014-05-01 00:00:00

  • An analytical solution for the stress state at stent-coating interfaces.

    abstract：:In this paper an analytical solution for the stress state in a coated stent is presented, with a particular focus on the interface stresses between the coating and stent. As a first step a simplified stent architecture consisting of a bi-layered composite elastic arch is considered. The variations of normal and shear ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2012.02.009

    authors： Parry G,McGarry P

    更新日期：2012-06-01 00:00:00

  • Nonlinear quasi-static finite element simulations predict in vitro strength of human proximal femora assessed in a dynamic sideways fall setup.

    abstract：:Osteoporotic proximal femur fractures are caused by low energy trauma, typically when falling on the hip from standing height. Finite element simulations, widely used to predict the fracture load of femora in fall, usually include neither mass-related inertial effects, nor the viscous part of bone׳s material behavior....

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.11.026

    authors： Varga P,Schwiedrzik J,Zysset PK,Fliri-Hofmann L,Widmer D,Gueorguiev B,Blauth M,Windolf M

    更新日期：2016-04-01 00:00:00

  • Air-abrasion using new silica-alumina powders containing different silica concentrations: Effect on the microstructural characteristics and fatigue behavior of a Y-TZP ceramic.

    abstract：:This study assessed the fatigue performance (biaxial flexure fatigue strength), surface characteristics (topography and roughness) and structural stability (t-m phase transformation) of a Y-TZP ceramic subjected to air-abrasion using new powders (7% and 20% silica-coated aluminum oxide particles) in comparison to comm...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.05.032

    authors： Cadore-Rodrigues AC,Prochnow C,Rippe MP,Oliveira JS,Jahn SL,Foletto EL,Pereira GKR,Valandro LF

    更新日期：2019-10-01 00:00:00

  • Setting mechanism of a new injectable Dicalcium Phosphate Dihydrate (DCPD) forming cement.

    abstract：:We previously described the gelation mechanism of calcium polyphosphate (CPP) in the presence of water. In this study, we developed novel and injectable poly-dicalcium phosphate dihydrate (P-DCPD) forming cement by the reaction of acidic CPP gel with alkali tetracalcium phosphate (TTCP). The setting reaction mechanism...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2017.12.032

    authors： Ren W,Song W,Yurgelevic S,Markel DC

    更新日期：2018-03-01 00:00:00

  • Osteogenesis enhancement of silk fibroin/ α-TCP cement by N-acetyl cysteine through Wnt/β-catenin signaling pathway in vivo and vitro.

    abstract：:High brittleness and lack osteogenesis are two major limitations of calcium phosphate cement (CPC) in application in bone defect reconstruction. Here we prepared a composite calcium phosphate cement by mixing N-acetyl cysteine loaded silk fibroin solution with α-tricalcium phosphate. In vitro cytology experiment revea...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103451

    authors： Feng T,Niu J,Pi B,Lu Y,Wang J,Zhang W,Li B,Yang H,Zhu X

    更新日期：2020-01-01 00:00:00

  • Relationships between the morphology, swelling and mechanical properties of poly(dimethyl siloxane)/poly(acrylic acid) interpenetrating networks.

    abstract：:A limitation in the use of hydrophilic polymers as implantable devices is their inherently poor mechanical strength. Using interpenetrating polymer networks (IPNs) consisting of both hydrophilic and hydrophobic networks is an effective method of strengthening these polymers. In this work, a series of poly(dimethyl sil...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2009.01.002

    authors： Jalili K,Abbasi F,Oskoee SS,Alinejad Z

    更新日期：2009-10-01 00:00:00

  • Adhesion of ligand-conjugated biosynthesized magnetite nanoparticles to triple negative breast cancer cells.

    abstract：:This paper presents the results of an experimental study of the adhesion forces between components of model conjugated magnetite nanoparticle systems for improved selectivity in the specific targeting of triple negative breast cancer. Adhesion forces between chemically synthesized magnetite nanoparticles (CMNPs), bios...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2017.02.004

    authors： Obayemi JD,Hu J,Uzonwanne VO,Odusanya OS,Malatesta K,Anuku N,Soboyejo WO

    更新日期：2017-04-01 00:00:00

  • Evaluating thoracolumbar spine response during simulated underbody blast impact using a total human body finite element model.

    abstract：:In a study of spine injuries in Operation Iraqi Freedom (OIF) and Operation Enduring Freedom (OEF) from 2001-09, spinal fractures sustained by mounted soldiers accounted for 26% of all injuries, and of that, 43% were caused by explosions [1]. The thoracolumbar region is the most vulnerable area of the spine [2], and i...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103398

    authors： Somasundaram K,Zhang L,Sherman D,Begeman P,Lyu D,Cavanaugh JM

    更新日期：2019-12-01 00:00:00

  • The relevance of molecular weight in the design of amorphous biodegradable polymers with optimized shape memory effect.

    abstract：:The shape memory effect (SME) has long been the focus of interest of many research groups that have studied many facets of it, yet to the authors' knowledge some molecular parameters, such as the molecular weight, have been skipped. Thus, the aim of this work is to offer further insight into the shape memory effect, b...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.04.027

    authors： Petisco-Ferrero S,Fernández J,Fernández San Martín MM,Santamaría Ibarburu PA,Sarasua Oiz JR

    更新日期：2016-08-01 00:00:00

  • Improved tribocorrosion performance of bio-functionalized TiO2 nanotubes under two-cycle sliding actions in artificial saliva.

    abstract：:After insertion into bone, dental implants may be subjected to tribocorrosive conditions resulting in the release of metallic ions and solid wear debris, which can induce to peri-implant inflammatory reactions accompanied by bone loss, and ultimately implant loosening. Despite the promising ability of TiO2 nanotubes (...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.01.038

    authors： Alves SA,Rossi AL,Ribeiro AR,Toptan F,Pinto AM,Shokuhfar T,Celis JP,Rocha LA

    更新日期：2018-04-01 00:00:00

  • In vivo assessment of material properties of muscles and connective tissues around the knee joint based on shear wave elastography.

    abstract：:Previous studies on knee biomechanics have mainly focused on the joint structure itself, largely neglecting the material properties of the muscles and connective tissues around the knee joint. Therefore, this study was purposed to conduct a systematic in vivo examination of the material properties of muscles, tendons,...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.103829

    authors： Wu J,Qian Z,Liang W,Liu J,Ren L,Ren L

    更新日期：2020-09-01 00:00:00

  • A finite element analysis of diaphragmatic hernia repair on an animal model.

    abstract：:The diaphragm is a mammalian skeletal muscle that plays a fundamental role in the process of respiration. Alteration of its mechanical properties due to a diaphragmatic hernia contributes towards compromising its respiratory functions, leading to the need for surgical intervention to restore the physiological conditio...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.06.005

    authors： de Cesare N,Trevisan C,Maghin E,Piccoli M,Pavan PG

    更新日期：2018-10-01 00:00:00

  • Finite element simulation for the mechanical characterization of soft biological materials by atomic force microscopy.

    abstract：:The characterization of the mechanical properties of soft materials has been traditionally performed through uniaxial tensile tests. Nevertheless, this method cannot be applied to certain extremely soft materials, such as biological tissues or cells that cannot be properly subjected to these tests. Alternative non-des...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.05.006

    authors： Valero C,Navarro B,Navajas D,García-Aznar JM

    更新日期：2016-09-01 00:00:00

  • Development of novel zirconia implant's materials gradated design with improved bioactive surface.

    abstract：:Zirconia implants are becoming a preference choice for different applications such as knee, dental, among others. In order to improve osseointegration, implant's surfaces are usually coated with bioactive materials like hydroxyapatite (HAp) and beta-tricalcium phosphate (β-TCP) that are very similar to the calcium pho...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.02.022

    authors： Faria D,Pires JM,Boccaccini AR,Carvalho O,Silva FS,Mesquita-Guimarães J

    更新日期：2019-06-01 00:00:00

  • Vancomycin elution, activity and impact on mechanical properties when added to orthopedic bone cement.

    abstract：:Infection incidence for total hip and knee arthroplasty (THA and TKA, respectively) is between 0.2% and 5% and results in approximately 100,000 device failures per year in the United States. Treatment requires prolonged systemic antibiotic therapy with additional surgical revisions. As a prophylactic measure against i...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.06.033

    authors： Bishop AR,Kim S,Squire MW,Rose WE,Ploeg HL

    更新日期：2018-11-01 00:00:00