Abstract：
:This in vitro study evaluated microleakage in Class II cavities restored with dental composite and varying light-curing units and the temperature of the composite when subjected to a thermocycling test. Ninety cavities were prepared on the proximal surfaces of bovine teeth and randomly divided according to the light-curing mode (QTH-420 mW/cm2, LED 2nd generation-1100 mW/cm2, or LED 3rd generation-700 mW/cm2) and temperature of the resin composite (23°C, 54°C and 60°C). Following the restorative procedures and thermocycling, the samples were immersed in methylene blue for 12 hours. The samples were ground and the powder prepared for analysis in an absorbance spectrophotometer. All the results were statistically analyzed using the nonparametric tests of Kruskal-Wallis and Dunn (p ≤ 0.05). The results showed that there was no statistical difference between the light-curing modes at a temperature of 23°C. For 54°C, QTH showed a microleakage mean that was significantly lower than those of the LED groups, and for 60°C, QTH had a microleakage mean significantly lower than that of the LED 2nd generation group. There was no statistical difference between the temperatures of the resin composite when LEDs were used. For QTH, 54°C showed statistically lower microleakage than 23°C. The group preheated to 60°C showed no difference when compared to the group heated to 23°C. Preheating the resin composite (54°C and 60°C) did not improve the microleakage means when high-irradiance LED was used; however, it decreased the microleakage means when a QTH with low irradiance was used.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
dos Santos RE,Lima AF,Soares GP,Ambrosano GM,Marchi GM,Lovadino JR,Aguiar FHdoi
10.2341/10-226-LR1subject
Has Abstractpub_date
2011-01-01 00:00:00pages
60-5issue
1eissn
0361-7734issn
1559-2863journal_volume
36pub_type
杂志文章abstract：:The current study compared the marginal adaptation of Class II open-sandwich restorations with a RMGIC versus a dual-cure composite as dentin substitute. Class II cavities were prepared on 50 extracted human third molars. The teeth were randomly assigned to two groups of 25 teeth to compare one dual cure composite (Mu...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/08-29
更新日期：2009-03-01 00:00:00
abstract：:A fundamental issue of restorative treatment is assessing the different conditions of cases not only from tooth-to-tooth but also from the activity of each caries lesion and the size of the cavity. In addition, restorative treatment is sometimes carried out for prosthetic and cosmetic purposes and involves cutting sou...
journal_title：Operative dentistry
pub_type：
doi：
更新日期：2002-05-01 00:00:00
abstract：:Dentin bridging of 150 mechanically exposed monkey pulps to two adhesive resins [BondWell LC (BW); Clearfil Liner Bond II (LB)] and a calcium hydroxide cement [Dycal (DY)] were histopathologically evaluated at 3, 7, 14, 30, and 60 days after operation (n = 10). The dentin bridge structure was three-dimensionally recon...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-05-01 00:00:00
abstract：:This study evaluated in vitro the necessity of retention grooves in approximal boxes in class 2 preparations with faciolingually wide occlusal extensions (occlusal isthmus width 1.8 mm). Thirty-six class 2 mesio-occlusal cavities were prepared in sound human maxillary premolar teeth and divided into three groups of 12...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1993-03-01 00:00:00
abstract：:Even though accuracy and inter-examiner variation assessments of borderline restorative items have been previously reported, no attempt has been made to replicate the effect of cumulative, sequential diagnostic and treatment planning decisions. This study assesses the cumulative effect of factors indicating restorativ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-07-01 00:00:00
abstract：:A study was conducted to compare the shear bond strength of a glass-ionomer cement and glass-ionomer base to coronal and radicular dentin. Two different glass ionomers were bonded to paired coronal and radicular human dentin surfaces that had received no surface treatment or had been treated passively for 20 seconds w...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-07-01 00:00:00
abstract：OBJECTIVES:To evaluate the effect of minocycline and chlorhexidine pretreatment of acid-etched dentin on the longevity of resin-dentin bond strength (μTBS) and nanoleakage of two-step etch-and-rinse adhesives. METHODS:Before application of Prime & Bond NT and Adper Single Bond 2 in occlusal dentin, the dentin surfaces...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-023-L
更新日期：2016-09-01 00:00:00
abstract：PURPOSE:To investigate the effect of different light-curing units and depths on the degree of conversion (DC) through Fourier transform infrared spectroscopy (FTIR) and Knoop Hardness Number (KHN) of a silorane-based composite resin (Filtek LS, 3M ESPE, St Paul, MN, USA) (LS). MATERIALS AND METHODS:LS specimens mounte...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/12-479
更新日期：2014-05-01 00:00:00
abstract：:The aim of this study was to determine whether using a silane-containing universal adhesive as a silane primer in glass-ceramic/resin cement systems affects biaxial flexural strength (BFS) and bonded interface integrity after loading. Glass-ceramic (IPS e.max CAD, Ivoclar/Vivadent, Schaan, Liechtenstein) disc-shaped s...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-356-L
更新日期：2019-03-01 00:00:00
abstract：:The purpose of this study was to determine if the actual concentration of bleaching agents available in four different countries were the same as the label indicated and within the recommendations of the International Standard on Tooth Whitening. The method recommended for assaying peroxide by the United States Pharma...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-367-L
更新日期：2013-05-01 00:00:00
abstract：:This study determined the influence of light curing protocols and matrix type on the margin quality and marginal seal of Class II resin-based composite restorations. In extracted human molars, box-shaped MOD cavities with 1 mm wide interproximal bevels were prepared with cervical margins located at least 1 mm coronal ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/04-194
更新日期：2006-01-01 00:00:00
abstract：:This study compared the viscoelastic properties of restorative and flowable bulk-fill resin-based composites (RBCs) with their conventional counterparts and evaluated the impact of aqueous solutions on viscoelastic properties. The materials examined included three conventional RBCs (Filtek Z350, Tetric N Ceram, and Be...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-005-L
更新日期：2020-03-01 00:00:00
abstract：:The present study investigated the effect of three high-viscosity bulk-fill resin-based composite materials on cuspal deflection in natural teeth. Thirty-two sound maxillary premolar teeth with large slot mesio-occlusal-distal cavities were distributed into four groups (n=8). Three groups were restored with bulk-fill ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-072-L
更新日期：2018-01-01 00:00:00
abstract：:On occasion we receive manuscripts that we would like to publish, but do not have the page room to include in the print journal. For the full article, please go to www.jopdentonline.org or enter the provided address into your address bar. ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/1559-2863-43.3.335
更新日期：2018-05-01 00:00:00
abstract：:Most manufacturers of dental adhesives have both a total-etch adhesive and a simplified self-etching adhesive available on the market. This study measured the enamel microtensile bond strengths of five pairs of enamel adhesives as a function of enamel roughness. The proximal surfaces of 25 extracted mandibular molars ...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-07-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate the influence of thermal cycling on the flexural properties and simulated wear of computer-aided design/computer-aided manufacturing (CAD/CAM) resin composites. METHODS:The six CAD/CAM resin composites used in this study were 1) Lava Ultimate CAD/CAM Restorative (LU)...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-046-L
更新日期：2017-01-01 00:00:00
abstract：:The effect of interdental separation of a special separation ring and wooden wedge was investigated. In a split-mouth design, 27 patients were randomly assigned to one of two groups (W or S). In 11 patients, an interdental wooden wedge (Hawe-Neos) was placed (group W), and in 16 patients, a separation ring (Composi-Ti...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-73
更新日期：2007-05-01 00:00:00
abstract：:Bleaching-induced tooth sensitivity (TS) is highly prevalent. OBJECTIVE:This study aimed to determine if the combination of opioids and nonopioids analgesics (Tylex) may provide a better analgesic effect. METHOD:A triple-blind, parallel, randomized two-center clinical trial was conducted with 105 healthy patients wh...
journal_title：Operative dentistry
pub_type： 杂志文章,多中心研究,随机对照试验
doi：10.2341/17-092-C
更新日期：2018-03-01 00:00:00
abstract：:The purpose of this study was to compare the long-term survivals of two low-copper and three high-copper amalgam alloys, and to analyze four clinical factors for their possible effects on the restoration survivals. Some 1476 polished restorations were placed in hospital patients by a large number of operators and asse...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1991-09-01 00:00:00
abstract：OBJECTIVES:To evaluate the effect of application protocol in resin-enamel microshear bond strength (μSBS), in situ degree of conversion, and etching pattern of three universal adhesive systems. METHODS AND MATERIALS:Sixty-three extracted third molars were sectioned in four parts (buccal, lingual, and proximals) and di...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-213-L
更新日期：2016-09-01 00:00:00
abstract：OBJECTIVES:To evaluate the effect of different surface treatments on the bond strength to a composite and a polymer-infiltrated ceramic CAD/CAM block after six-month artificial aging. METHODS AND MATERIALS:Two types of CAD/CAM blocks (Cerasmart, GC; Enamic, Vita Zahnfabrik) were cut in slabs of 4-mm thickness, divided...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-263-L
更新日期：2017-01-01 00:00:00
abstract：:This in vitro study evaluated the amount of fluoride released from fluoride-containing materials over a period of 28 days. Six disk samples (2.06 +/- 0.06 cm2) were prepared of each material and divided at random into seven groups: Group 1: Chelon-Fil; Group 2: Chelon-Silver; Group 3: VariGlass; Group 4: Dyract; Group...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1996-09-01 00:00:00
abstract：:Most currently marketed fluoride varnishes (FVs) have not been evaluated for their effectiveness in preventing dental caries. The objective of this study was to investigate the anticaries efficacy, measured as fluoride release into artificial saliva (AS); change in surface microhardness of early enamel caries lesions;...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-040-L
更新日期：2019-09-01 00:00:00
abstract：:The present in vitro study concerns determination of the pre-cementation gap width of all-ceramic crowns made using an in-office digital-impression technique and subsequent computer-aided design/computer-aided manufacturing (CAD/CAM) production. Two chairside video camera systems were used: the Lava Oral scanner and C...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/12-309-L
更新日期：2014-05-01 00:00:00
abstract：:This study evaluated the microleakage of resin-modified glass ionomer, flowable compomer and flowable resin composite restorations on a Class V cavity of simulated advanced root caries under a flexural load cycling condition. Thirty-six non-carious human maxillary premolars were mounted in cylindrical acrylic resin mo...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-03-01 00:00:00
abstract：:This article reports the case of a patient with bilateral hypodontia of the maxillary lateral incisors who was dissatisfied with the outcome of initial orthodontic treatment, highlighting the importance of a multidisciplinary interaction among Restorative Dentistry, Orthodontics, and Implantology to achieve satisfacto...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-167-T
更新日期：2012-09-01 00:00:00
abstract：:The antibacterial effects of the dentin bonding systems Syntac, ProBOND, Gluma 3-Step, the resin-modified glass ionomers Photac-Fil, Fuji Lining LC, Fuji II LC, and the polyacid-modified composite resins VariGlass, Geristore, and Infinity were evaluated using the cariogenic bacteria S mutans, L salivarius, S sobrinus,...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1996-11-01 00:00:00
abstract：:This article outlines an atraumatic isolation approach and a conservative instrumentation sequence, followed by use of a highly viscous, rapid-setting, capsulated glass ionomer cement to manage a difficult deep proximal-cervical Class V lesion. ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-05-01 00:00:00
abstract：:Treatment of a caries active patient requires the clinician to be knowledgeable in the restorative and risk management issues with which these patients often present. Modifications of risk factors that promote dental caries play an important part in the long-term restorative success in these patients. Patient complian...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2002-03-01 00:00:00
abstract：:This study determined the effect of bleaching agents on the fracture toughness of composite materials. Four nanofilled resin composites were evaluated: Filtek Supreme Plus, Tetric EvoCeram, Premise and Esthet-X. Four concentrations of bleaching agents were tested: Opalescence PF 10%, 20%, 35% and 45%. Fifty specimens ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/08-120-L
更新日期：2009-11-01 00:00:00
