Abstract：
:In previous studies, enamel showed indications to occlude small cracks in-vivo and exhibited R-curve behaviors for bigger cracks ex-vivo. This study quantifies the crack tip's toughness (K(I0),K(III0)), the crack's closure stress and the cohesive zone size at the crack tip of enamel and investigates the toughening mechanisms near the crack tip down to the length scale of a single enamel crystallite. The crack-opening-displacement (COD) profile of cracks induced by Vickers indents on mature bovine enamel was studied using atomic force microscopy (AFM). The mode I crack tip toughness K(I0) of cracks along enamel rod boundaries and across enamel rods exhibit a similar range of values: K(I0,Ir)=0.5-1.6MPa m(0.5) (based on Irwin's 'near-field' solution) and K(I0,cz)=0.8-1.5MPa m(0.5) (based on the cohesive zone solution of the Dugdale-Muskhelishvili (DM) crack model). The mode III crack tip toughness K(III0,Ir) was computed as 0.02-0.15MPa m(0.5). The crack-closure stress at the crack tip was computed as 163-770 MPa with a cohesive zone length and width 1.6-10.1μm and 24-44 nm utilizing the cohesive zone solution. Toughening elements were observed under AFM and SEM: crack bridging due to protein ligament and hydroxyapatite fibres (micro- and nanometer scale) as well as microcracks were identified.
journal_name
J Mech Behav Biomed Materauthors
Ang SF,Schulz A,Pacher Fernandes R,Schneider GAdoi
10.1016/j.jmbbm.2010.12.003subject
Has Abstractpub_date
2011-04-01 00:00:00pages
423-32issue
3eissn
1751-6161issn
1878-0180pii
S1751-6161(10)00178-5journal_volume
4pub_type
杂志文章abstract：:Characterization of the mechanical properties of biological materials is often complicated by small volume, irregular geometry, fragility, and environmental sensitivity. Pipette aspiration and nanoindentation testing deal well with these limitations and have seen increasing use in biomaterial characterization, but lit...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.07.022
更新日期：2015-11-01 00:00:00
abstract：:The retrogradation of high amylose starch (5% or 10%), by isothermal cycles at 4°C (method 1) or by alternating thermal cycles (method 2) was efficient and promoted important structural modifications. Hydrogels of gellan gum and starch retrograded blends, containing or not ketoprofen, were prepared by ionic and dual c...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.08.005
更新日期：2017-01-01 00:00:00
abstract：:This paper presents a strain-based damage model to predict the stress-strain relationship and investigate the damage onset and evolution of the fibre and matrix of a fully bio-resorbable phosphate glass fibre reinforced composite under three-point bending. The flexural properties of the composite are crucial, particul...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.02.022
更新日期：2018-05-01 00:00:00
abstract：:Zirconia implants are becoming a preference choice for different applications such as knee, dental, among others. In order to improve osseointegration, implant's surfaces are usually coated with bioactive materials like hydroxyapatite (HAp) and beta-tricalcium phosphate (β-TCP) that are very similar to the calcium pho...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.02.022
更新日期：2019-06-01 00:00:00
abstract：:Intervertebral disc (IVD) degeneration is a naturally, irreparable process that causes loss in IVD hydration, cellularity, and, mechanical stability. Invasive surgical attempts to ease back pain and, radiculopathy have shown to cause increased degeneration along the rest, of the spine. Due to its highly tunable mechan...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.05.014
更新日期：2017-08-01 00:00:00
abstract：:Modeling human body response to dynamic loading events and developing biofidelic human surrogate systems require accurate material properties over a range of loading rates for various human organ tissues. This work describes a technique for measuring the shear properties of soft biomaterials at high rates of strain (1...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.06.008
更新日期：2011-11-01 00:00:00
abstract：:Mechanotransduction, the encoding of local mechanical stresses and strains at sensory endings into neural action potentials at the viscera, plays a critical role in evoking visceral pain, e.g., in the distal colon and rectum (colorectum). The wall of the colorectum is structurally heterogeneous, including two major co...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104127
更新日期：2021-01-01 00:00:00
abstract：:Superelastic wires and diamond-shaped stent surrogates were manufactured from Nitinol rods and tubing, respectively, from five different mill product suppliers - Standard VAR, Standard VIM, Standard VIM+VAR, Process-Optimized VIM+VAR, and High-Purity VAR. High-cycle fatigue tests up to 10(7) cycles were conducted unde...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.07.003
更新日期：2015-11-01 00:00:00
abstract：:We aimed to investigate the fatigue strength of Co-Cr-Mo clasps for removable partial dentures prepared by selective laser melting (SLM). The Co-Cr-Mo alloy specimens for tensile tests (dumbbell specimens) and fatigue tests (clasp specimens) were prepared by SLM with varying angles between the building and longitudina...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.02.032
更新日期：2016-06-01 00:00:00
abstract：:Porous poly(para-phenylene) (PPP) scaffolds have tremendous potential as an orthopedic biomaterial; however, the underlying mechanisms controlling the monotonic and cyclic behavior are poorly understood. The purpose of this study was to develop a method to integrate micro-computed tomography (μCT), finite-element anal...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.10.004
更新日期：2015-01-01 00:00:00
abstract：:Experimental investigations for anatomic variation in the magnitude and anisotropy of elastic constants in human femoral cortical bone tissue have typically focused on a limited number of convenient sites near the mid-diaphysis. However, the proximal and distal ends of the diaphysis are more clinically relevant to com...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2008.08.005
更新日期：2009-07-01 00:00:00
abstract：:The unique properties of highly nonlinear solitary waves in granular chains have prompted extensive research in the area of non-destructive testing and led to the development of new diagnostic schemes with potential applications in the healthcare industry. Here, we study numerically the interaction between highly nonl...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103805
更新日期：2020-09-01 00:00:00
abstract：:Impaction bone grafting is a method of restoring bone stock to patients who have suffered significant bone loss due to revision total hip surgery. The procedure requires morsellised cancellous bone (MCB) to be impacted into the site of bone loss in order to stabilise the prosthesis with the aim of long term resorption...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.11.002
更新日期：2018-02-01 00:00:00
abstract：PURPOSE:To compare osseointegration and implant stability of two types of laser-etched (LE) Ti implants with a chemically-modified, sandblasted, large-grit and acid-etched (SLA) Ti implant (SLActive(®), Straumann, Basel, Switzerland), by evaluating removal torque and resonance frequency between the implant surface and ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.03.034
更新日期：2016-08-01 00:00:00
abstract：OBJECTIVES:The deviation and spread of values measured by tensile strength tests should be significantly reduced by optimized axially pull-off-device. MATERIAL AND METHODS:Factors like geometry, roughness, surface texture and fit of the specimens, the luting procedure (mixing ratio, compacting pressure) were standardi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.07.003
更新日期：2018-11-01 00:00:00
abstract：:Enamel possesses a complex hierarchical structure, which bestows this tissue with unique mechanical properties. In this study, the mechanical behavior of single enamel rods was investigated under uniaxial compression. Numerical simulations were also performed using micromechanics models for individual enamel rods to i...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.10.014
更新日期：2015-02-01 00:00:00
abstract：:The use of highly sensitive soft materials has become increasingly apparent in the last few years in numerous industrial fields, due to their viscous and damping nature. Unfortunately these materials remain difficult to characterize using conventional techniques, mainly because of the very low internal forces supporte...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.06.008
更新日期：2016-10-01 00:00:00
abstract：:The superior biotribological performance of nanocrystalline diamond (NCD) coatings grown by a chemical vapor deposition (CVD) method was already shown to demonstrate high wear resistance in ball on plate experiments under physiological liquid lubrication. However, tests with a close-to-real approach were missing and t...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.05.005
更新日期：2015-09-01 00:00:00
abstract：:Bioink plays a major role in 3D printing of tissues and organs. Alginate is a widely used component for bioinks but its cellular responses are limited, which limits its clinical translation. In this study, we demonstrate the printability and cellular compatibility of composite bioink consists of sodium alginate (NaAlg...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103642
更新日期：2020-04-01 00:00:00
abstract：:Due to its proximity to the mitral valve, the coronary sinus (CS) vessel serves as a conduit for the deployment and implantation of the percutaneous transvenous mitral annuloplasty (PTMA) devices that can potentially reduce the mitral regurgitation. Because CS vessel is a venous tissue and seldom diseased, its mechani...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.09.001
更新日期：2012-02-01 00:00:00
abstract：:According to the literature, there are many mathematical relationships between density of the trabecular bone and mechanical properties obtained in macro-scale testing. In micro-scale, the measurements provide only the ranges of Young׳s modulus of trabeculae, but there are no experimentally tested relationships allowi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.04.011
更新日期：2014-08-01 00:00:00
abstract：:The objective of this study was to develop a nanoscratch technique that can be used to measure the in situ toughness of bone at micro/nanostructural levels. Among the currently possible techniques, the surface scratch test may be conducted on very small regions, thus exhibiting a potential in determining the in situ f...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.08.019
更新日期：2012-01-01 00:00:00
abstract：:The evolution of the bone-implant interface reflects the implant osseointegration and bond strength, thereby determining the overall implant stability in the jawbone. Quantitative ultrasound represents a promising alternative technique to characterize the interfacial integrity, precisely due to the fact that those wav...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.103547
更新日期：2020-03-01 00:00:00
abstract：:In the present work, we propose the first structural constitutive model of the passive mechanical behavior of the swine colon that is validated against physiological inflation-extension tests, and accounts for residual strains. Sections from the spiral colon and the descending colon were considered to investigate pote...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.08.031
更新日期：2018-01-01 00:00:00
abstract：:This paper presents an improved identification method of the constitutive properties of lung parenchyma. We aim to determine the non-linear viscoelastic behavior of lung parenchyma with a particular focus on the compressible properties - i.e. the ability to change volume. Uniaxial tensile tests are performed on living...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.09.018
更新日期：2014-01-01 00:00:00
abstract：:This review attempts to show the bone community that there are many ways of being a 'bone', and that the range of mechanical properties of bone material is much greater than is conventionally thought to be the case. However the structure-function relationships have in many cases hardly moved beyond mere assertion. The...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章,评审
doi：10.1016/j.jmbbm.2010.03.002
更新日期：2010-07-01 00:00:00
abstract：:The differentiation of hepatic stellate cells (HSCs) into myofibroblasts is a key event in liver fibrosis. Due to the local stiffening of the extracellular matrix (ECM) during fibrosis, it is of great interest to develop mimics that can be used to investigate the cellular response to changes in mechanics. Here, we use...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.11.008
更新日期：2014-10-01 00:00:00
abstract：:The surface of commercially pure Ti (cp-Ti) substrate was grit-blasted with Al(2)O(3) powders and then wet-blasted with HAp/Ti mixed powders at room temperature. Then plasma spraying with Ti powders or HAp/Ti mixed powders on the blasted surface was carried out to form a bond coat layer, denoted as T50 and T100 bond c...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2008.11.001
更新日期：2009-10-01 00:00:00
abstract：:A newly designed hydroxyapatite-polyurethane (HA-PU) composite scaffold was prepared by polymerizing glyceride of castor oil (GCO) with isophorone diisocyanate (IPDI) and HA as fillers. The aim of this study was to determine the effect of HA fillers on the mechanical properties and osteogenesis capacity of the composi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.08.028
更新日期：2018-12-01 00:00:00
abstract：BACKGROUND AND AIMS:The course and outcome of pregnancy is closely correlated to change of biomechanical properties of the uterine cervix. The aim of this study was to build a non-linear, fiber reinforced mechanical model of the cervix for estimation of mechanical characteristics of the cervix in early- and term-pregna...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.07.005
更新日期：2014-11-01 00:00:00
