Abstract：
PURPOSE:To compare osseointegration and implant stability of two types of laser-etched (LE) Ti implants with a chemically-modified, sandblasted, large-grit and acid-etched (SLA) Ti implant (SLActive(®), Straumann, Basel, Switzerland), by evaluating removal torque and resonance frequency between the implant surface and rabbit tibia bones. We used conventional LE Ti implants (conventional LE implant, CSM implant, Daegu, Korea) and LE Ti implants that had been chemically activated with 0.9% NaCl solution (LE active implant) for comparison with SLActive(®) implants MATERIALS AND METHODS:Two types of 3.3×8mm laser-etched Ti implants - conventional LE implants and LE active implants were prepared. LE implants and SLActive(®) implants were installed on the left and right tibias of 10 adult rabbits weighing approximately 3.0kg LE active implants and SLActive(®) implants were installed on the left and right tibias of 11 adult rabbits. After installation, we measured insertion torque (ITQ) and resonance frequency (ISQ). Three weeks (LE active) or 4 weeks (conventional LE) after installation, we measured removal torque (RTQ) and ISQ. RESULTS:In the conventional LE experiment, the mean ITQ was 16.99±6.35Ncm for conventional LE implants and 16.11±7.36Ncm for SLActive(®) implants (p=0.778>0.05). After 4 weeks, the mean of RTQ was 39.49±17.3Ncm for LE and 42.27±20.5Ncm for SLActive(®) (p=0.747>0.05). Right after insertion of the implants, the mean ISQ was 74.8±4.98 for conventional LE and 70.1±9.15 for SLActive(®) implants (p=0.169>0.05). After 4 weeks, the mean ISQ was 64.40±6.95 for LE and 67.70±9.83 for SLActive(®) (p=0.397>0.05). In the LE active experiment, the mean ITQ was 16.24±7.49Ncm for LE active implants and 14.33±5.06Ncm for SLActive(®) implants (p=0.491>0.05). After 3 weeks, the mean RTQ was 39.25±16.41Ncm for LE active and 41.56±10.41Ncm for SLActive(®) implants (p=0.698>0.05). Right after insertion of the implants, the mean ISQ was 58.64±10.51 for LE active implants and 53.82±15.36 for SLActive(®) implants (p=0.401>0.05). After 3 weeks, the mean ISQ was 63.82±5.88 for LE active and 66.27±6.53 for SLActive(®) (p=0.365>0.05). CONCLUSION:We observed no significant differences in biomechanical bond strength to bone or implant stability in bone between the conventional LE Ti implant surface and the surface of the SLActive(®) implant or between the chemically activated LE Ti implant surface and the surface of the SLActive(®) implant during the early stage of osseointegration.
journal_name
J Mech Behav Biomed Materauthors
Lee JT,Cho SAdoi
10.1016/j.jmbbm.2016.03.034subject
Has Abstractpub_date
2016-08-01 00:00:00pages
299-307eissn
1751-6161issn
1878-0180pii
S1751-6161(16)30064-9journal_volume
61pub_type
杂志文章abstract：:For three decades, low level laser therapy (LLLT) has been used for treatment of tendinitis as well as other musculoskeletal diseases. Nevertheless, the biological mechanisms involved remain not completely understood. In this work, the effects of LLLT and of the widely used nonsteroidal anti-inflammatory drug, diclofe...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.08.028
更新日期：2014-01-01 00:00:00
abstract：:The impact response of body armor composed of a ceramic plate with an ultrahigh molecular weight polyethylene (UHMWPE) fiber-reinforced composite and layers of UHMWPE fibers shielding a block of ballistic gelatin has been experimentally and numerically analyzed. It is a surrogate model for studying injuries to human t...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.01.010
更新日期：2015-05-01 00:00:00
abstract：STATEMENT OF PROBLEM:The surface hardness and roughness of different glaze materials for denture base acrylic resins have not been well reported. PURPOSE:The purpose of the study was to measure the surfaces hardness, elastic modulus and surface roughness of 5 different light-polymerized glaze materials for poly methyl...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.103601
更新日期：2020-03-01 00:00:00
abstract：:Determination of correlations between transmural mechanical and morphological properties of aorta would provide a quantitative baseline for assessment of preventive and therapeutic strategies for aortic injuries and diseases. A multimodal and multidisciplinary approach was adopted to characterize the transmural morpho...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.03.004
更新日期：2015-07-01 00:00:00
abstract：:In previous studies, enamel showed indications to occlude small cracks in-vivo and exhibited R-curve behaviors for bigger cracks ex-vivo. This study quantifies the crack tip's toughness (K(I0),K(III0)), the crack's closure stress and the cohesive zone size at the crack tip of enamel and investigates the toughening mec...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2010.12.003
更新日期：2011-04-01 00:00:00
abstract：:Enamel possesses a complex hierarchical structure, which bestows this tissue with unique mechanical properties. In this study, the mechanical behavior of single enamel rods was investigated under uniaxial compression. Numerical simulations were also performed using micromechanics models for individual enamel rods to i...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.10.014
更新日期：2015-02-01 00:00:00
abstract：OBJECTIVES:The causes of in vivo fractures of all-ceramic dental crowns are not yet fully understood. The fracture origins often occur in the cervical margin in the approximal area, but the reason for this is unclear. The aim of this study was to evaluate the fracture origin of 22 of clinically-failed alumina crowns. ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.08.006
更新日期：2016-01-01 00:00:00
abstract：:In recent years, scaffolds produced in 3D printing technology have become more widespread tool due to providing more advantages than traditional methods in tissue engineering applications. In this research, it was aimed to produce patches for the treatment of tympanic membrane perforations which caused significant hea...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104219
更新日期：2021-02-01 00:00:00
abstract：:The superior biotribological performance of nanocrystalline diamond (NCD) coatings grown by a chemical vapor deposition (CVD) method was already shown to demonstrate high wear resistance in ball on plate experiments under physiological liquid lubrication. However, tests with a close-to-real approach were missing and t...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.05.005
更新日期：2015-09-01 00:00:00
abstract：OBJECTIVES:The aim of the present study was to investigate the surface characteristic, biomechanical behavior, hemocompatibility, bone tissue response and osseointegration of the optimal micro-arc oxidation surface-treated titanium (MST-Ti) dental implant. MATERIALS AND METHODS:The surface characteristic, biomechanica...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.11.042
更新日期：2018-03-01 00:00:00
abstract：:High brittleness and lack osteogenesis are two major limitations of calcium phosphate cement (CPC) in application in bone defect reconstruction. Here we prepared a composite calcium phosphate cement by mixing N-acetyl cysteine loaded silk fibroin solution with α-tricalcium phosphate. In vitro cytology experiment revea...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.103451
更新日期：2020-01-01 00:00:00
abstract：:Nitinol self-expanding stents are effective in treating peripheral artery disease, including the superficial femoral, carotid, and renal arteries. However, fracture occurrences of up to 50% have been reported in some stents after one year. These stent fractures are likely due to in vivo cyclic displacements. As such, ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2007.08.001
更新日期：2008-04-01 00:00:00
abstract：:The aim of the present work was twofold: to prepare biphasic magnesium fluorapatite (MFA) composites with different amounts of alumina using a two-step sintering process, and to evaluate the effects of various amounts of alumina on the mechanical properties, phase stability, and densification of the composite samples....
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.08.004
更新日期：2014-12-01 00:00:00
abstract：:Grit blasting is used as a cost-effective method to increase the surface roughness of metallic biomaterials, as Ti6Al4V and 316 LVM, to enhance the osteointegration, fixation and stability of implants. Samples of these two alloys were blasted by using alumina and zirconia particles, yielding rough (up to Ra~8μm) and n...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.10.013
更新日期：2014-02-01 00:00:00
abstract：:Severe degeneration of the intervertebral disc has an immensely debilitating effect on quality of life that has become a serious health and economic burden throughout the world. The disc plays an integral role in biomechanical movement and support within the spine. The emergence of tissue engineering endeavours to res...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.10.015
更新日期：2017-01-01 00:00:00
abstract：:Even though bariatric surgery is one of the most effective treatment option of obesity, post-surgical weight loss is not always ensured, especially in the long term, when many patients experience weight regain. Bariatric procedures are largely based on surgeon's expertise and intra-operative decisions, while an integr...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103883
更新日期：2020-10-01 00:00:00
abstract：:The shape memory effect (SME) has long been the focus of interest of many research groups that have studied many facets of it, yet to the authors' knowledge some molecular parameters, such as the molecular weight, have been skipped. Thus, the aim of this work is to offer further insight into the shape memory effect, b...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.04.027
更新日期：2016-08-01 00:00:00
abstract：:In the study, the microstructure, mechanical property and metal release behavior of selective laser melted CoCrW alloys under different solution treatment conditions were systemically investigated to assess their potential use in orthopedic implants. The effects of the solution treatment on the microstructure, mechani...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.10.019
更新日期：2015-03-01 00:00:00
abstract：:The purpose of this study is to construct bone tissue engineering scaffold with high porosity, good mechanical properties, and biological activities. Bioactive glass/gelatin composite scaffolds with different amounts of tetrapod zinc oxide whiskers were produced. The morphology, mechanical properties and in vitro bioa...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.01.032
更新日期：2017-04-01 00:00:00
abstract：BACKGROUND:Perfusion bioreactors are used to solve problems in critical size bone tissue engineering. Biominerizable and biocompatible nanocomposites are suitable scaffold materials for this purpose because they offer mineral components in organic carriers. Human adipose derived stem cells (ASCs) can potentially be use...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.03.022
更新日期：2015-07-01 00:00:00
abstract：:Imprecise knowledge on the composition-processing-microstructure-property correlation of titanium alloys combined with experimental data are used for developing rule based models for predicting the strength and elastic modulus of titanium alloys. The developed models are used for designing alloys suitable for orthoped...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.08.039
更新日期：2016-01-01 00:00:00
abstract：:Vascular calcification is a complex molecular process that exhibits a number of relatively characteristic morphology patterns in atherosclerotic plaques. Treatment of arterial stenosis by endovascular intervention, involving forceful circumferential expansion of the plaque, can be unpredictable in calcified lesions. T...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.11.001
更新日期：2016-03-01 00:00:00
abstract：:Reuse of NiTi orthodontic wires has become increasingly common in dental clinics. For sterilization and recovery of the original superelastic properties of the wires, a heat treatment is usually performed between 500 and 600 °C. The aim of this study was to analyze the effect of these thermal treatments on the mechani...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.11.005
更新日期：2012-02-01 00:00:00
abstract：:In the development of new materials for orthopedic implants, special attention has been given to Ti alloys that show biocompatible alloy elements and that are capable of reducing the elastic modulus. Accordingly, Ti-Nb-Si alloys show great potential for application. Thus, this is a study on the microstructures and pro...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.06.035
更新日期：2015-11-01 00:00:00
abstract：:Single-cell technologies are powerful tools to evaluate cell characteristics. In particular, Atomic Force Microscopy (AFM) nanoindentation experiments have been widely used to study single cell mechanical properties. One important aspect related to single cell techniques is the need for sufficient statistical power to...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.03.018
更新日期：2019-06-01 00:00:00
abstract：:Uniaxial tensile tests were performed to investigate the mechanical properties of the ultra-high molecular weight polyethylene (UHMWPE) with different modification conditions. It was found that the different modification conditions have great influence on the mechanical properties of the UHMWPE. Subsequently, the unia...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.08.022
更新日期：2018-12-01 00:00:00
abstract：:Anterior cervical discectomy with fusion is a common surgical treatment that can relieve patients suffering from cervical spondylosis. This surgery is most commonly performed with the use of a cervical cage. One serious complication of the fusion cages commercially available in the market is subsidence of the cage wit...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.05.040
更新日期：2018-09-01 00:00:00
abstract：:We report failure analysis of sternal wires in two cases in which a perichronal fixation technique was used to close the sternotomy. Various characteristics of the retrieved wires were compared to those of unused wires of the same grade and same manufacturer and with surgical wire specifications. In both cases, wire f...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.02.015
更新日期：2011-10-01 00:00:00
abstract：:Determination of the material properties of soft tissue is a growing area of interest that aids in the development of new surgical tools and surgical simulators. This study first aims to develop a robot-operated tissue testing system for determination of tissue cutting forces. Second, this system was used to ascertain...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.06.010
更新日期：2018-10-01 00:00:00
abstract：:The paper describes a highly space-resolved characterization of the surface mechanical properties of the posterior human corneal layer (Descemet's membrane). This has been accomplished with Atomic Force Microscopy (AFM) nano-indentation by using a probe with a sharp tip geometry. Results indicate that the contact with...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.05.019
更新日期：2017-10-01 00:00:00
