Abstract:
BACKGROUND:Computer modeling is used to predict inhaled aerosol deposition in the lung based on definition of the aerosol characteristics and the breathing pattern and airway anatomy of the subject. Validation of the models is limited by the lack of detailed experimental data. Three-dimensional imaging provides an opportunity to address this unmet need. METHODS:Radioactive aerosol was administered to six male asthmatic subjects on two occasions under carefully monitored input conditions. Input parameters varied in particle size, depth of breathing, and carrier gas. The aerosol distribution was measured by combined single photon emission computed tomography and x-ray computer tomography (SPECT/CT) and airway anatomy by high resolution CT. The deposition distribution was measured by both a 2D and 3D analysis and described in terms of the percentage of inhaled aerosol deposited in sections of the respiratory tract and in both spatial and anatomical subdivisions within each lung. The percentage deposition in the conducting airways was also assessed by 24 h clearance. RESULTS:A set of imaging data of aerosol deposition has thus been produced in which the input parameters of inhalation are well described. The results in asthmatics were compared to previous measurements in healthy controls using an identical inhalation protocol. The percentages of deposition in extra-thoracic and thoracic compartments of the airways were not significantly affected by disease, but the regional pulmonary deposition pattern was, with asthma leading to increased deposition in the conducting airways. CONCLUSIONS:The dataset acquired in this study will be useful in validating computer models of aerosol deposition in asthmatic subjects. Asthma did not affect the fraction of inhaled aerosol depositing in the lungs, but gave rise to a more central deposition pattern. The use of 3D SPECT imaging in combination with 24 h clearance measurements enables differentiation of deposition between bronchial and bronchiolar airways.
journal_name
J Aerosol Med Pulm Drug Delivjournal_title
Journal of aerosol medicine and pulmonary drug deliveryauthors
Fleming J,Conway J,Majoral C,Katz I,Caillibotte G,Pichelin M,Montesantos S,Bennett Mdoi
10.1089/jamp.2014.1191subject
Has Abstractpub_date
2015-12-01 00:00:00pages
432-51issue
6eissn
1941-2711issn
1941-2703journal_volume
28pub_type
杂志文章abstract:PURPOSE:Many methods have been developed to evaluate dry powder inhalation techniques and their efficiency for disease control in asthma patients. However, it is difficult to apply these methods to clinical practice and research. In this study, we introduce a simple new method that can be applied to dry powder inhalati...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2014.1193
更新日期:2016-10-01 00:00:00
abstract::The present study aimed at assessing the pharmacokinetics (PK) and safety pharmacodynamics (PD) of 24 microg formoterol delivered via a Novolizer and via an Aerolizer in healthy subjects. This was a randomized, open-label, crossover study. Beside PK, serum potassium, and glucose profiles, vital signs, and ECG were rec...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,随机对照试验
doi:10.1089/jamp.2008.0690
更新日期:2008-09-01 00:00:00
abstract:: Background: Many substances used in inhalation research are water soluble and can be administered as nebulized solutions. Typical examples are therapeutic, small-molecular agents, or macromolecules. Another category is a number of water-soluble agents used for airway diagn...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2019.1554
更新日期:2020-04-01 00:00:00
abstract:BACKGROUND:The Respimat Soft Mist Inhaler is reported to generate an aerosol with low spray momentum and a small droplet size. However, the transport characteristics of the Respimat aerosol are not well understood. The objective of this study was to characterize the transport and deposition of an aerosol emitted from t...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0708
更新日期:2009-06-01 00:00:00
abstract::Upper respiratory tract infections (URTIs), primarily acute rhinopharyngitis, tonsillitis, adenoiditis, and rhinosinusitis (RS), are major causes of morbidity in both children and adults of any age. In addition to the frequent occurrence of related medical problems and the associated socioeconomic costs, URTIs have a ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2016.1300
更新日期:2017-02-01 00:00:00
abstract::The success of inhalation therapy is not only dependent upon the pharmacology of the drugs being inhaled but also upon the site and extent of deposition in the respiratory tract. Similarly, the toxicity of environmental and industrial particulate matter is affected not only by the nature of the dust but also by the am...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2020.29029.cd
更新日期:2020-08-01 00:00:00
abstract:PURPOSE:The objective of this study was to determine optimal aerosol delivery conditions for a full-term (3.6 kg) infant receiving invasive mechanical ventilation by evaluating the effects of aerosol particle size, a new wye connector, and timing of aerosol delivery. METHODS:In vitro experiments used a vibrating mesh ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2013.1077
更新日期:2014-10-01 00:00:00
abstract:BACKGROUND:Inhaled corticosteroid (ICS) therapy has improved the quality of life (QOL) for many asthmatics and reduced mortality rates associated with asthma. However, some patients do not obtain therapeutic benefit despite satisfactory adherence. OBJECTIVES:To determine whether asthmatic patients were using ICS devic...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2010.0868
更新日期:2011-12-01 00:00:00
abstract:BACKGROUND:Researchers, using checklists, have identified that 30%-90% of patients make errors in inhaler use. It is not certain whether these errors affect the delivery of medication. We have developed an electronic monitor (INCA™) that records audio each time an inhaler is used, providing objective information on inh...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2016.1334
更新日期:2017-08-01 00:00:00
abstract:BACKGROUND:Dyspnea significantly impacts quality of life and is one of the most common symptoms in advanced illness. Systemically-administered opioids and benzodiazepines have been the most studied and utilized pharmacologic treatments for refractory dyspnea. Less attention has been given to the use of these medication...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2014.1136
更新日期:2015-02-01 00:00:00
abstract:: Background: Inhalation of medications is the cornerstone in the treatment of patients with lung diseases. A variety of inhalation devices exists and each device has specific requirements to achieve optimum inhalation of the drug. The goal of this study was to establish a c...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1376
更新日期:2018-12-01 00:00:00
abstract:BACKGROUND:The delivery of antitubercular drugs through direct lung targeting can lead to reduction in the dose as well as side effects of the drug. In the present investigation, carrier (lactose)-based dry-powder inhaler of rifampicin was prepared to achieve direct targeting of the drug into the lungs. METHODS:The dr...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1379
更新日期:2017-12-01 00:00:00
abstract:BACKGROUND:Very little is known about the role of nasal morphology due to ethnic variation on particle deposition pattern in the sinonasal cavity. This preliminary study utilizes computational fluid dynamics (CFD) modeling to investigate sinonasal airway morphology and deposition patterns of intranasal sprayed particle...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2014.1205
更新日期:2016-04-01 00:00:00
abstract:: Background: Salvia miltiorrhiza polyphenolic acid (SMPA) is effective in the treatment of cardiovascular diseases and currently it is administered orally or intravenously. However, SMPA is poorly absorbed orally and quickly eliminated in vivo. A long-term frequent intraveno...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2019.1538
更新日期:2020-04-01 00:00:00
abstract::Exhaled breath condensate (EBC) consists mainly of water, but also contains semivolatile and nonvolatile compounds. The aim of this study was to develop a system in which two condensers are simultaneously used in series to clarify the mechanisms of EBC condensation. Two aliquots of EBC (EBC1 and EBC2) were collected f...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2007.0644
更新日期:2008-03-01 00:00:00
abstract::The use of gamma camera imaging following the inhalation of a radiolabel has been widely used by researchers to investigate the fate of inhaled aerosols. The application of two-dimensional (2D) planar gamma scintigraphy and single-photon emission computed tomography (SPECT) to the study of inhaled aerosols is discusse...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2011.0960
更新日期:2013-06-01 00:00:00
abstract:BACKGROUND:The effectiveness of metered-dose inhalers (MDIs) in delivering medication to the lungs highly depends on its correct usage technique. Current guidelines state optimal technique for high lung deposition should include a slow inhalation (>5 seconds) at an inspiratory flow rate of 30 L/min and inhaler actuatio...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1278
更新日期:2017-08-01 00:00:00
abstract:BACKGROUND:Particle size and velocity are two of the most significant factors that impact the deposition of pressurized metered-dose inhaler (pMDI) sprays in the mouth cavity. pMDIs are prominently used around the world in the treatment of patients suffering from a variety of lung diseases such as asthma and chronic ob...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1264
更新日期:2016-12-01 00:00:00
abstract:BACKGROUND:Inhaled alpha1-antitrypsin (AAT) is being developed for treatment of cystic fibrosis to protect the lungs from excessive free elastase. High drug costs mandate a very efficient aerosol system to deliver a high payload to the airways. The I-neb Adaptive Aerosol Delivery (AAD) System is a portable, electronic,...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2009.0793
更新日期:2010-04-01 00:00:00
abstract:BACKGROUND:Inhaled atropine is being developed as a systemic and pulmonary treatment for the extended recovery period after chemical weapons exposure. We performed a pharmacokinetics study comparing inhaled atropine delivery using the MicroDose Therapeutx Dry Powder Inhaler (DPIA) with intramuscular (IM) atropine deliv...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,随机对照试验
doi:10.1089/jamp.2011.0948
更新日期:2013-02-01 00:00:00
abstract:BACKGROUND:The site of deposition in the respiratory tract for aerosolized, inhaled therapeutic drugs depends on both the particles' aerodynamic size and the patient's breathing pattern. METHODS:In 21 healthy subjects with normal lung function, we evaluated an extremely slow inhalation of a large 9.5-μm MMAD particle ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0711
更新日期:2010-12-01 00:00:00
abstract::Flexhaler is a multiple-dose, inspiratory flow-driven dry powder inhaler that is a newer version of Turbuhaler, and is identical to the Symbicort Turbuhaler. Sustained performance is of the utmost importance to ensure consistent drug delivery throughout the lifespan of the inhaler. We report functionality testing resu...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0700
更新日期:2008-12-01 00:00:00
abstract:: Background: Many countries have introduced a compulsory use of community masks for certain public areas during the SARS-CoV-2 pandemic. Different manufacturers offer reusable community masks in large quantities. The efficacy of these masks, however, is unknown. ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2020.1635
更新日期:2020-09-23 00:00:00
abstract:BACKGROUND:Predicting local lung tissue pharmacodynamic (PD) responses of inhaled drugs is a longstanding challenge related to the lack of experimental techniques to determine local free drug concentrations. This has prompted the use of physiologically based pharmacokinetic (PBPK) modeling to potentially predict local ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1436
更新日期:2019-02-01 00:00:00
abstract:BACKGROUND:Spiromax(®) is a novel dry powder inhaler for patients with asthma or chronic obstructive pulmonary disease (COPD). The studies presented here provide further data on attributes (in vitro dosing consistency with budesonide-formoterol (DuoResp) Spiromax; flow rates through empty versions of the Spiromax and T...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1216
更新日期:2015-10-01 00:00:00
abstract::Inhalation is a potentially viable route of administration for numerous agents. In diabetes mellitus, the need for frequent injections to achieve ideal glycemic control remains a significant limitation for initiating and complying with insulin therapy in a large number of patients. To overcome this barrier, inhaled in...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2011.0876
更新日期:2011-10-01 00:00:00
abstract:BACKGROUND:Currently bronchial provocation testing (BPT) using mannitol powder cannot be performed in children under 6 years. A primary reason is it is challenging for children at this age to generate a consistent inspiratory effort to inhale mannitol efficiently from a dry powder inhaler. A prototype system, which doe...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1208
更新日期:2015-12-01 00:00:00
abstract:BACKGROUND:The unit dose dry powder inhaler (UD-DPI) is being considered as an alternative inhaler platform that, if developed, has the potential to improve access to inhaled respiratory medicines in developing countries. AIM:This study compared the systemic exposure of fluticasone furoate after delivery from the UD-D...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,随机对照试验
doi:10.1089/jamp.2016.1322
更新日期:2017-10-01 00:00:00
abstract:BACKGROUND:The Abbreviated Impactor Measurement (AIM) concept simplifies determination of aerodynamic size metrics for inhaler quality control testing. A similar approach is needed to compare in vitro particle size distribution metrics with human respiratory tract (HRT) deposition. METHODS:An abbreviated impactor base...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2011.0925
更新日期:2012-08-01 00:00:00
abstract:BACKGROUND:Remote inhaler monitoring is an emerging technology that enables the healthcare team to monitor the time and location of a patient's inhaler use. We assessed the feasibility of remote inhaler monitoring for chronic obstructive pulmonary disease (COPD) patients and the pattern of albuterol inhaler use associa...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1383
更新日期:2018-06-01 00:00:00