Abstract:
: Background: Many substances used in inhalation research are water soluble and can be administered as nebulized solutions. Typical examples are therapeutic, small-molecular agents, or macromolecules. Another category is a number of water-soluble agents used for airway diagnostics or disease modeling. Mesh nebulizers have facilitated well-controlled liquid aerosol exposures. Meanwhile, a benchtop inhalation platform, PreciseInhale, was developed for providing small-scale, well-controlled aerosol exposures in preclinical configurations. The purpose of the current research was to adapt the Aerogen mesh nebulizer to work within the PreciseInhale system for both cell culture and rodent exposures. Methods: The wet aerosols produced with the Aerogen Pro nebulizer were dried out in an aerosol holding chamber by supplying dry carrier air, which was provided by passing the incoming ambient air through a column with silica gel. The nebulizer was installed in an aerosol holding chamber between an upstream flow-rate pneumotach and a downstream aerosol monitor. By pulsing, the nebulizer output was reduced to 1%-10% of continuous operation to better match the exposure ventilation requirements. Additional drying was obtained by mantling the holding chamber with dried paper. Results and Conclusions: The nebulizer output was reduced to 3-30 μL/min and dried out before reaching the in vitro or in vivo exposure modules. Using solute concentrations in the range of 0.5%-2% (w/w), dried aerosols were produced with a mass median aerodynamic diameter of 1.5-2.0 μm, compared to the 4-5 μm droplets emitted by the nebulizer. Controlling the Aerogen nebulizer under a reduced output scheme within the PreciseInhale platform gave two major advantages: (i) by reducing aerosol output to better match exposure flow rates of single rodents, increased airway deposition yields were obtained in a range of 1%-10% relative to the nebulized amount of test substance and (ii) shrinking aerosol particle sizes through drying improved the peripheral lung deposition of test aerosols.
journal_name
J Aerosol Med Pulm Drug Delivjournal_title
Journal of aerosol medicine and pulmonary drug deliveryauthors
Gerde P,Nowenwik M,Sjöberg CO,Selg Edoi
10.1089/jamp.2019.1554subject
Has Abstractpub_date
2020-04-01 00:00:00pages
116-126issue
2eissn
1941-2711issn
1941-2703journal_volume
33pub_type
杂志文章abstract:: Background: The photo reflection method (PRM) is used to measure light reflected from particles released from dry powder inhalers (DPIs). This simple method depicts time trajectories of released drugs; however, it underestimates the number of particles at high peak inhalat...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2020.1610
更新日期:2020-11-04 00:00:00
abstract:BACKGROUND:Preclinical evaluation of new chemical entities (NCEs) designed to be administered by inhalation route requires lung administration to rodents, especially in the discovery phase. Different administration methods have been used until now, but more efforts are required to obtain controlled and reproducible lun...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1369
更新日期:2018-02-01 00:00:00
abstract:BACKGROUND:Small rodents continue to be the mainstay for the assessment of pharmacological and toxicological data of inhaled therapeutics. For meaningful interpretation of the results information about deposition of aerosol particles in the respiratory tract is warranted, but not trivial to obtain for animals with nose...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2011.0902
更新日期:2012-06-01 00:00:00
abstract:PURPOSE:Many methods have been developed to evaluate dry powder inhalation techniques and their efficiency for disease control in asthma patients. However, it is difficult to apply these methods to clinical practice and research. In this study, we introduce a simple new method that can be applied to dry powder inhalati...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2014.1193
更新日期:2016-10-01 00:00:00
abstract:BACKGROUND:Remote inhaler monitoring is an emerging technology that enables the healthcare team to monitor the time and location of a patient's inhaler use. We assessed the feasibility of remote inhaler monitoring for chronic obstructive pulmonary disease (COPD) patients and the pattern of albuterol inhaler use associa...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1383
更新日期:2018-06-01 00:00:00
abstract:BACKGROUND:Particle size and velocity are two of the most significant factors that impact the deposition of pressurized metered-dose inhaler (pMDI) sprays in the mouth cavity. pMDIs are prominently used around the world in the treatment of patients suffering from a variety of lung diseases such as asthma and chronic ob...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1264
更新日期:2016-12-01 00:00:00
abstract::Flexhaler is a multiple-dose, inspiratory flow-driven dry powder inhaler that is a newer version of Turbuhaler, and is identical to the Symbicort Turbuhaler. Sustained performance is of the utmost importance to ensure consistent drug delivery throughout the lifespan of the inhaler. We report functionality testing resu...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0700
更新日期:2008-12-01 00:00:00
abstract:BACKGROUND:Mechanically ventilated patients commonly suffer from ventilator-associated pneumonia, hypoxemia, and other lower respiratory tract infection as a result of pathogen colonization and poor sputum clearance. Consequently, there is a high rate of morbidity and mortality in these patients. Dry powder mannitol in...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2016.1320
更新日期:2017-04-01 00:00:00
abstract:BACKGROUND:Secondary lung infections are the primary cause of morbidity associated with cystic fibrosis lung disease. Aerosolized antibiotic inhalation is potentially advantageous but has limited effectiveness due to altered airway aerodynamics and deposition patterns that limit drug access to infected regions. One pot...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2017.1412
更新日期:2018-08-01 00:00:00
abstract:PURPOSE:The objective of this study was to determine optimal aerosol delivery conditions for a full-term (3.6 kg) infant receiving invasive mechanical ventilation by evaluating the effects of aerosol particle size, a new wye connector, and timing of aerosol delivery. METHODS:In vitro experiments used a vibrating mesh ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2013.1077
更新日期:2014-10-01 00:00:00
abstract::Significant advances have been made in the last 50 years in developing safe and efficacious aerosol formulations for pulmonary delivery. The key to future innovation may lie at the interface between biology and particle engineering. Improved understanding of biological processes including particle clearance, cellular ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2010.0838
更新日期:2010-12-01 00:00:00
abstract::Exhaled breath condensate (EBC) consists mainly of water, but also contains semivolatile and nonvolatile compounds. The aim of this study was to develop a system in which two condensers are simultaneously used in series to clarify the mechanisms of EBC condensation. Two aliquots of EBC (EBC1 and EBC2) were collected f...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2007.0644
更新日期:2008-03-01 00:00:00
abstract:: Background: Many countries have introduced a compulsory use of community masks for certain public areas during the SARS-CoV-2 pandemic. Different manufacturers offer reusable community masks in large quantities. The efficacy of these masks, however, is unknown. ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2020.1635
更新日期:2020-09-23 00:00:00
abstract:OBJECTIVES:This experimental study was conducted to determine the effects of training on inhaler technique and quality of life in patients with chronic obstructive pulmonary disease (COPD). METHODS:Among the patients who applied at the outpatient clinic of chest diseases between March 2009 and May 2010, a total of 69 ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,随机对照试验
doi:10.1089/jamp.2012.1017
更新日期:2013-12-01 00:00:00
abstract:BACKGROUND:The Abbreviated Impactor Measurement (AIM) concept simplifies determination of aerodynamic size metrics for inhaler quality control testing. A similar approach is needed to compare in vitro particle size distribution metrics with human respiratory tract (HRT) deposition. METHODS:An abbreviated impactor base...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2011.0925
更新日期:2012-08-01 00:00:00
abstract:BACKGROUND:To validate the 'Test of Adherence to Inhalers' (TAI), a 12-item questionnaire designed to assess the adherence to inhalers in patients with COPD or asthma. METHODS:A total of 1009 patients with asthma or COPD participated in a cross-sectional multicenter study. Patients with electronic adherence ≥80% were ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,多中心研究
doi:10.1089/jamp.2015.1212
更新日期:2016-04-01 00:00:00
abstract:BACKGROUND:The effectiveness of metered-dose inhalers (MDIs) in delivering medication to the lungs highly depends on its correct usage technique. Current guidelines state optimal technique for high lung deposition should include a slow inhalation (>5 seconds) at an inspiratory flow rate of 30 L/min and inhaler actuatio...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1278
更新日期:2017-08-01 00:00:00
abstract:BACKGROUND:Inhaled corticosteroid (ICS) therapy has improved the quality of life (QOL) for many asthmatics and reduced mortality rates associated with asthma. However, some patients do not obtain therapeutic benefit despite satisfactory adherence. OBJECTIVES:To determine whether asthmatic patients were using ICS devic...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2010.0868
更新日期:2011-12-01 00:00:00
abstract::The present study aimed at assessing the pharmacokinetics (PK) and safety pharmacodynamics (PD) of 24 microg formoterol delivered via a Novolizer and via an Aerolizer in healthy subjects. This was a randomized, open-label, crossover study. Beside PK, serum potassium, and glucose profiles, vital signs, and ECG were rec...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,随机对照试验
doi:10.1089/jamp.2008.0690
更新日期:2008-09-01 00:00:00
abstract:BACKGROUND:Computer modeling is used to predict inhaled aerosol deposition in the lung based on definition of the aerosol characteristics and the breathing pattern and airway anatomy of the subject. Validation of the models is limited by the lack of detailed experimental data. Three-dimensional imaging provides an oppo...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2014.1191
更新日期:2015-12-01 00:00:00
abstract:BACKGROUND:To our knowledge, quantification of intranasal deposition of aerosol generated by Accuspray(™) (AS) in children has never been published. We hypothesized that deposition would vary significantly with age and with placement of the device within, or outside, of the nostril. METHODS:We tested these hypotheses ...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2014.1174
更新日期:2015-10-01 00:00:00
abstract::The use of gamma camera imaging following the inhalation of a radiolabel has been widely used by researchers to investigate the fate of inhaled aerosols. The application of two-dimensional (2D) planar gamma scintigraphy and single-photon emission computed tomography (SPECT) to the study of inhaled aerosols is discusse...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2011.0960
更新日期:2013-06-01 00:00:00
abstract:BACKGROUND:The Respimat Soft Mist Inhaler is reported to generate an aerosol with low spray momentum and a small droplet size. However, the transport characteristics of the Respimat aerosol are not well understood. The objective of this study was to characterize the transport and deposition of an aerosol emitted from t...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0708
更新日期:2009-06-01 00:00:00
abstract:BACKGROUND:High flow nasal cannula oxygen therapy (HFT) is increasingly used in intensive and emergency care departments. Patients suffering from respiratory failure, who are likely to benefit from HFT, may require aerosolized bronchodilators; therefore, combining nebulization with HFT may be relevant. This study aimed...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1219
更新日期:2016-04-01 00:00:00
abstract::The success of inhalation therapy is not only dependent upon the pharmacology of the drugs being inhaled but also upon the site and extent of deposition in the respiratory tract. Similarly, the toxicity of environmental and industrial particulate matter is affected not only by the nature of the dust but also by the am...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2020.29029.cd
更新日期:2020-08-01 00:00:00
abstract:BACKGROUND:Spiromax(®) is a novel dry powder inhaler for patients with asthma or chronic obstructive pulmonary disease (COPD). The studies presented here provide further data on attributes (in vitro dosing consistency with budesonide-formoterol (DuoResp) Spiromax; flow rates through empty versions of the Spiromax and T...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1216
更新日期:2015-10-01 00:00:00
abstract::Since the early 1960s, there has been a continuous evolution in scientific understanding regarding bioequivalence (BE) of oral dosage forms, intermittently punctuated by some breakthrough research findings and conceptual advances. The accumulated knowledge from this body of research has been translated into a sophisti...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2014.1144
更新日期:2014-12-01 00:00:00
abstract::Antibiotic-resistant bacterial infections have renewed interest in finding substitute methods of treatment. The purpose of the present in vitro study was to investigate the possibility of respiratory delivery of a Burkholderia cepacia complex (BCC) bacteriophage by nebulized aerosol administration. Bacteriophages in i...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2008.0701
更新日期:2008-12-01 00:00:00
abstract:BACKGROUND:Currently bronchial provocation testing (BPT) using mannitol powder cannot be performed in children under 6 years. A primary reason is it is challenging for children at this age to generate a consistent inspiratory effort to inhale mannitol efficiently from a dry powder inhaler. A prototype system, which doe...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章
doi:10.1089/jamp.2015.1208
更新日期:2015-12-01 00:00:00
abstract::This article provides a concise review of the use of magnetic resonance imaging (MRI) for measurement of regional aerosol deposition in the lungs. Basic aspects of MRI and its use in lung imaging and measurement of regional ventilation are introduced. Imaging of hydrogen protons (water) and inhaled hyperpolarized gase...
journal_title:Journal of aerosol medicine and pulmonary drug delivery
pub_type: 杂志文章,评审
doi:10.1089/jamp.2011.0897
更新日期:2012-04-01 00:00:00