Abstract:
:Cavitation plays important roles in almost all high-intensity focused ultrasound (HIFU) applications. However, current two-dimensional (2D) cavitation mapping could only provide cavitation activity in one plane. This study proposed a three-dimensional (3D) ultrasound plane-by-plane active cavitation mapping (3D-UPACM) for HIFU in free field and pulsatile flow. The acquisition of channel-domain raw radio-frequency (RF) data in 3D space was performed by sequential plane-by-plane 2D ultrafast active cavitation mapping. Between two adjacent unit locations, there was a waiting time to make cavitation nuclei distribution of the liquid back to the original state. The 3D cavitation map equivalent to the one detected at one time and over the entire volume could be reconstructed by Marching Cube algorithm. Minimum variance (MV) adaptive beamforming was combined with coherence factor (CF) weighting (MVCF) or compressive sensing (CS) method (MVCS) to process the raw RF data for improved beamforming or more rapid data processing. The feasibility of 3D-UPACM was demonstrated in tap-water and a phantom vessel with pulsatile flow. The time interval between temporal evolutions of cavitation bubble cloud could be several microseconds. MVCF beamformer had a signal-to-noise ratio (SNR) at 14.17dB higher, lateral and axial resolution at 2.88times and 1.88times, respectively, which were compared with those of B-mode active cavitation mapping. MVCS beamformer had only 14.94% time penalty of that of MVCF beamformer. This 3D-UPACM technique employs the linear array of a current ultrasound diagnosis system rather than a 2D array transducer to decrease the cost of the instrument. Moreover, although the application is limited by the requirement for a gassy fluid medium or a constant supply of new cavitation nuclei that allows replenishment of nuclei between HIFU exposures, this technique may exhibit a useful tool in 3D cavitation mapping for HIFU with high speed, precision and resolution, especially in a laboratory environment where more careful analysis may be required under controlled conditions.
journal_name
Ultrasonicsjournal_title
Ultrasonicsauthors
Ding T,Hu H,Bai C,Guo S,Yang M,Wang S,Wan Mdoi
10.1016/j.ultras.2016.04.010subject
Has Abstractpub_date
2016-07-01 00:00:00pages
166-81eissn
0041-624Xissn
1874-9968pii
S0041-624X(16)30021-Xjournal_volume
69pub_type
杂志文章相关文献
ULTRASONICS文献大全abstract::3D ultrasound is a promising imaging modality for clinical diagnosis and treatment monitoring. Its cost is relatively low in comparison with CT and MRI, no intensive training and radiation protection is required for its operation, and its hardware is movable and can potentially be portable. In this study, we developed...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2004.05.003
更新日期:2005-01-01 00:00:00
abstract::For medical high frequency acoustic imaging purposes the reduction in size of a single transducer element for one-dimensional and even more for two-dimensional arrays is more and more limited by fabrication and cabling technology. In the fields of industrial distance measurement and simple object recognition low cost ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(99)00085-2
更新日期:2000-03-01 00:00:00
abstract::This paper presents the experimental study of a miniaturized surface acoustic waves (SAWs) rotary motor and the theoretical calculation. After the first success in SAW rotary motor operating at 9.85 MHz, a smaller rotary motor is designed. With the operating frequency of 30 MHz and the driving voltage of 120 V(p-p), t...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(02)00264-0
更新日期:2002-06-01 00:00:00
abstract::This paper focuses on transmission characteristics of fundamental symmetric Lamb mode (So) at the junction of a main waveguide and sub-waveguides in composite laminates. Numerical simulations on transmission of So from the main to sub-waveguide revealed that transmission factors of the modes depend on stacking sequenc...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2015.08.003
更新日期:2016-01-01 00:00:00
abstract::Traditional rotary corers and sample retrieval mechanisms for planetary drilling suffer from a variety of technical difficulties. A heavy and rigid drillstring must be assembled on-site and deployed with considerable applied preload and torque, and these mechanical loadings are difficult to react in a low gravity envi...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2011.06.001
更新日期:2011-12-01 00:00:00
abstract::Knowing the low-frequency response of hydrophones, down to 100 kHz at least, is important for accurate biomedical ultrasound measurements. However, current international standards do not extend below 500 kHz. Furthermore, commercial hydrophone sources typically do not supply sensitivity data below 1-2 MHz. Therefore, ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2003.12.008
更新日期:2004-04-01 00:00:00
abstract::The ultrasound-induced harmonic microbubble response spectrum is known to shift to lower frequencies with increasing tissue attenuation. We hypothesized that this shift could be reproducibly detected in received broadband radiofrequency spectra. We used an automatic Gaussian curve-fitting technique to measure the mean...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(02)00397-9
更新日期:2003-03-01 00:00:00
abstract::This paper deals with the analysis of the guided evanescent waves in stopbands of a 1D phononic crystal (PC). A new numerical implementation is shown in order to get the complex values of the wavenumbers in a frequency range where a gap occurs. The considered phononic system is an aluminum plate with a one-dimensional...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2012.09.009
更新日期:2013-02-01 00:00:00
abstract::The propagation of non-axisymmetric guided waves in larger diameter pipes is studied in this paper by treating the guided waves as corresponding Lamb waves in an unwrapped plate. This approximation leads to a simpler method for calculating the phase velocities of hollow cylinder guided waves, which reveals a beam focu...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2005.07.002
更新日期:2006-01-01 00:00:00
abstract::Ultrasonic reflection and transmission measurements on saturated, plane-parallel, poroelastic slabs are presented. A data processing technique is proposed to obtain poroelastic parameters from transmission measurements. A special experimental data acquisition and processing technique is applied to minimize the finite ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2008.10.006
更新日期:2009-03-01 00:00:00
abstract::The second and third-order Brugger elastic constants are obtained for liquids and ideal gases having an initial hydrostatic pressure p1. For liquids the second-order elastic constants are C₁₁=A+p₁, C₁₂=A-p₁, and the third-order constants are C₁₁₁=-(B+5A+3p₁), C₁₁₂=-(B+A-p₁), and C₁₂₃=A-B-p₁, where A and B are the Beye...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2014.01.012
更新日期:2014-07-01 00:00:00
abstract::The location of continuous acoustic emission sources is a difficult problem of non-destructive testing. This article describes one-dimensional location of continuous acoustic emission sources by using an intelligent locator. The intelligent locator solves a location problem based on learning from examples. To verify w...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(99)00079-7
更新日期:2000-03-01 00:00:00
abstract::An ultrasonic backscattering model is developed for textured polycrystalline materials with orthotropic or trigonal grains of ellipsoidal shape. The model allows us to simulate realistic microstructures and orthotropic macroscopic material textures resulting from thermomechanical processing for a broad variety of mate...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2014.02.020
更新日期:2014-09-01 00:00:00
abstract::The purpose of this study is to evaluate whether a 5-repetition liver stiffness (LS) measurement as the standard protocol of shear wave elastography (SWE) is comparable to a conventional 10-repetition measurement protocol and to identify factors that influence the reliability of the 5-repetition protocol. A total of 3...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2016.08.005
更新日期:2016-12-01 00:00:00
abstract::Forced fluid flow can cause the enhancement of multibubble sonoluminescence (SL) under suitable conditions. The effect of directional flow with a circulator is similar to that of rotating flow with a stirrer. The mechanism of the enhancement is that both flows prevent cavitation bubbles from coalescing and clustering,...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2006.05.022
更新日期:2006-12-22 00:00:00
abstract::Acoustic wave interaction with non-bonded contacts was found to be inherently non-linear due to asymmetrical stiffness distribution across the interface. A diode-type non-linearity results in local static elastic fields inside the contact, which are shown to be a source of transient longitudinal and shear DC-acoustic ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(02)00241-x
更新日期:2002-05-01 00:00:00
abstract::The purpose of this study was to investigate practical, safe, easy-to-use, non-cytotoxic, and reliable parameters to apply to an ultrasound (US) naked gene therapy system. The ultrasound pressure at the point of cell exposure was measured using a calibrated hydrophone and the intensity calculated. An acoustic power me...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2004.06.007
更新日期:2004-12-01 00:00:00
abstract::Sonoelectrochemistry is undergoing a reemerging activity in the last years with an increasing number of papers appearing in a wide range of peer review journals. Applied studies which cover environmental treatments, synthesis or characterization of nanostructures, polymeric materials synthesis, analytical procedures, ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2009.09.022
更新日期:2010-02-01 00:00:00
abstract::This will be a discussion of the non-invasive determination of the viscosity of a non-Newtonian fluid in laminar pipe flow over the range of shear rates present in the pipe. The procedure used requires knowledge of the flow profile in and the pressure drop along a long straight run of pipe. The profile is determined b...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2006.05.027
更新日期:2006-12-22 00:00:00
abstract::Shear-Horizontally (SH) polarized, ultrasonic, guided wave modes are considered in order to infer changes in the adhesive properties at several interfaces located within an adhesive bond joining two metallic plates. Specific aluminium lap-joint samples were produced, with different adhesive properties at up to four in...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2014.03.002
更新日期:2014-09-01 00:00:00
abstract::Acoustic scattering phenomena from complex immersed elastic shells are studied by high-speed Schlieren visualization for spark-generated spherical quasi-Dirac excitations. The situations considered are air-filled cylindrical shells under normal insonification and air-filled cylindrical shells soldered at one end with ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(99)00165-1
更新日期:2000-03-01 00:00:00
abstract::In most of industries as aeronautics, aerospace and nuclear, the main part of the ultrasonic testing is carried out directly in touch with the inspected component. Among others, the cooling piping of French pressurized water reactor comprises many welding components with complex geometry: elbows, butt welds, nozzles. ...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(02)00145-2
更新日期:2002-05-01 00:00:00
abstract::An improved method for ultrasonic location of multiple flaws using perpendicular ultrasonic arrays, working in near-field conditions, is presented. The method uses the pulse-echo technique and is based on the processing of the information acquired by both the elemental emitting transducers and their adjacent ones. Thi...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2006.05.107
更新日期:2006-12-22 00:00:00
abstract::Silver epoxy was selected to bond transducer plates on glass substrates. The properties and thickness of the bonding medium affect the electrical input impedance of the transducer. Thus, the thickness of the silver epoxy bonding layer was used as a design parameter to optimize the structure for the transducer input im...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2011.11.010
更新日期:2012-04-01 00:00:00
abstract::Transducer is the necessary and most important part in the maxonics. New applications demand for new transducer, and the renovation of the transducer will open a new field for the application of the maxonics. The important method to develop new transducer is to find and develop new material. The rare earth giant magne...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2006.05.128
更新日期:2006-12-22 00:00:00
abstract::The present investigation concerns the propagation of surface waves at the vacuum-solid interface of a solid which is isotropic and thermoviscoelastic, i.e., for which the effects of heat conductivity need to be taken into account. Calculations show that, in addition to the Rayleigh wave, a thermal surface wave propag...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(00)00017-2
更新日期:2000-07-01 00:00:00
abstract::Three-dimensional (3D) elastic wave simulations can be used to investigate and optimize nondestructive evaluation (NDE) and structural health monitoring (SHM) ultrasonic damage detection techniques for aerospace materials. 3D anisotropic elastodynamic finite integration technique (EFIT) has been implemented for ultras...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2013.05.007
更新日期:2014-01-01 00:00:00
abstract::Over the last two decades, more efficient transducers were developed for the generation and reception of air-borne ultrasound, thus enabling the non-contact, non-contaminating inspection of composite laminates and honeycomb structures widely used in the aerospace industry. This paper presents the fundamentals of makin...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2006.05.091
更新日期:2006-12-22 00:00:00
abstract::The aim of this work was to show the applicability of light diffraction tomography on airborne ultrasound in the frequency range 40 kHz-2 MHz. Seven different air-coupled transducers were measured to show the method's performance regarding linearity, absolute pressure measurements, phase measurements, frequency respon...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/s0041-624x(99)00168-7
更新日期:2000-01-01 00:00:00
abstract::The aim of this work is to investigate the absolute phase information in resonance acoustic scattering by spheres and cylinders and place this work in the broader context of scattering in which the properties of the magnitude and (processed) phase have been examined in a more general way than in the classical resonanc...
journal_title:Ultrasonics
pub_type: 杂志文章
doi:10.1016/j.ultras.2008.01.002
更新日期:2008-07-01 00:00:00