Natural beam focusing of non-axisymmetric guided waves in large-diameter pipes.

Abstract:

:The propagation of non-axisymmetric guided waves in larger diameter pipes is studied in this paper by treating the guided waves as corresponding Lamb waves in an unwrapped plate. This approximation leads to a simpler method for calculating the phase velocities of hollow cylinder guided waves, which reveals a beam focusing nature of non-axisymmetric guided waves generated by a partial source loading. The acoustic fields in a pipe generated by a partial-loading source includes axisymmetric longitudinal modes as well as non-axisymmetric flexural modes. The circumferential distribution of the total acoustic field, also referred as an angular profile, diverges circumferentially while guided waves propagate with dependence on such factors as mode, frequency, cylinder size, propagation distance, etc. Exact prediction of the angular profile of the total field can only be realized by numerical calculations. In particular cases, however, when the wall thickness is far less than the cylinder diameter and the wavelength is smaller than or comparable to the pipe wall thickness, the acoustic field can be analyzed based on the characteristics of Lamb waves that travel along a periodic unwrapped plate. Based on this assumption, a simplified model is derived to calculate the phase velocities of non-axisymmetric flexural mode guided waves. The model is then applied to discussions on some particular characteristics of guided-wave angular profiles generated by a source loading. Some features of flexural modes, such as cutoff frequency values are predicted with the simpler model. The relationship between the angular profiles and other factors such as frequency, propagation distance, and cylinder size is obtained and presented in simple equations. The angular profile rate of change with respect to propagation distance is investigated. In particular, our simplified model for non-axisymmetric guided waves predicts that the wave beam will converge to its original circumferential shape after the wave propagates for a certain distance. A concept of "natural focal point" is introduced and a simple equation is derived to compute the 1st natural focal distance of non-axisymmetric guided waves. The applicable range of the simplified equation is provided. Industrial pipes meet the requirement of wall thickness being far less than the pipe diameter. The approximate analytical algorithms presented in this paper provides a convenient method enabling quick acoustic field analysis on large-diameter industrial pipes for NDE applications.

journal_name

Ultrasonics

journal_title

Ultrasonics

authors

Li J,Rose JL

doi

10.1016/j.ultras.2005.07.002

subject

Has Abstract

pub_date

2006-01-01 00:00:00

pages

35-45

issue

1

eissn

0041-624X

issn

1874-9968

pii

S0041-624X(05)00063-6

journal_volume

44

pub_type

杂志文章
  • Guided wave propagation in a honeycomb composite sandwich structure in presence of a high density core.

    abstract::A coordinated theoretical, numerical and experimental study is carried out in an effort to interpret the characteristics of propagating guided Lamb wave modes in presence of a high-density (HD) core region in a honeycomb composite sandwich structure (HCSS). Initially, a two-dimensional (2D) semi-analytical model based...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.05.025

    authors: Sikdar S,Banerjee S

    更新日期:2016-09-01 00:00:00

  • Estimation of dispersion curves of water-loaded structures by using approximated acoustic mass.

    abstract::For coupled structures surrounded by heavy fluids, it is difficult to obtain dispersion curves from an eigenvalue analysis, because the external fluid term in the coupled equation includes transcendental functions for frequency and wavenumber. Thus, in this study, the acoustic mass of the external fluid was approximat...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2017.12.009

    authors: Jung BK,Ryue J,Hong C,Jeong WB,Shin KK

    更新日期:2018-04-01 00:00:00

  • An adaptive threshold filter for ultrasound signal rejection.

    abstract::The threshold filter is a frequently used technique in ultrasound B-scan to reject the small echoes contributed from backscattering that blur the tissue interface and reduce the image contrast. Note that using the threshold based on one value would simultaneously destroy local waveform features of the reflection echoe...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2008.10.007

    authors: Tsui PH,Chang CC,Chang CC,Huang NE,Ho MC

    更新日期:2009-05-01 00:00:00

  • Extended optical theorem for scalar monochromatic acoustical beams of arbitrary wavefront in cylindrical coordinates.

    abstract::One of the fundamental theorems in (optical, acoustical, quantum, gravitational) wave scattering is the optical theorem for plane waves, which relates the extinction cross-section to the forward scattering complex amplitude function. In this analysis, the optical theorem is extended for the case of 3D-beams of arbitra...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.01.006

    authors: Mitri FG

    更新日期:2016-04-01 00:00:00

  • Utility of quantitative ultrasound in community screening for hepatic steatosis.

    abstract::Nonalcoholic fatty liver disease (NAFLD) is the most common chronic liver disease. Quantitative ultrasound facilitates clinical grading of hepatic steatosis (the early stage of NAFLD). However, the utility of quantitative ultrasound as a first-line method for community screening of hepatic steatosis remains unclear. T...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106329

    authors: Chang TY,Chang SH,Lin YH,Ho WC,Wang CY,Jeng WJ,Wan YL,Tsui PH

    更新日期:2021-03-01 00:00:00

  • Multibubble sonoluminescence enhancement by fluid flow.

    abstract::Forced fluid flow can cause the enhancement of multibubble sonoluminescence (SL) under suitable conditions. The effect of directional flow with a circulator is similar to that of rotating flow with a stirrer. The mechanism of the enhancement is that both flows prevent cavitation bubbles from coalescing and clustering,...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.022

    authors: Hatanaka S,Mitome H,Yasui K,Hayashi S

    更新日期:2006-12-22 00:00:00

  • On the effect of lung filtering and cardiac pressure on the standard properties of ultrasound contrast agent.

    abstract::The goal standard of contrast echocardiography is the absolute measure of myocardial perfusion using a contrast agent. Actually, several contrast agents are developed. All these agents show left ventricular opacification after intravenous injection. However, none of these agents shows an acceptable enhancement of the ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(97)00137-6

    authors: Bouakaz A,de Jong N,Cachard C,Jouini K

    更新日期:1998-02-01 00:00:00

  • Numerical and experimental analysis of strongly nonlinear standing acoustic waves in axisymmetric cavities.

    abstract::In this paper the behaviour of strongly nonlinear waves in axisymmetric resonators is experimentally and numerically studied. Experiments are carried out in a cylindrical cavity, which transversal dimension is bigger than the longitudinal one, excited by a narrow band transducer. The quality factor and displacement am...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2005.02.001

    authors: Vanhille C,Campos-Pozuelo C

    更新日期:2005-08-01 00:00:00

  • Fabrication and comparison of PMN-PT single crystal, PZT and PZT-based 1-3 composite ultrasonic transducers for NDE applications.

    abstract::This paper describes fabrication and comparison of PMN-PT single crystal, PZT, and PZT-based 1-3 composite ultrasonic transducers for NDE applications. As a front matching layer between test material (Austenite stainless steel, SUS316) and piezoelectric materials, alumina ceramics was selected. The appropriate acousti...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2010.04.001

    authors: Kim KB,Hsu DK,Ahn B,Kim YG,Barnard DJ

    更新日期:2010-08-01 00:00:00

  • Tissue characterization of arteries with 4 MHz ultrasound.

    abstract::Reflections of 4 MHz ultrasound pulses from 60 sites on 15 human aorta specimens were analysed using the plane-wave Born approximation (PWBA) inverse scattering method. The recovered high-resolution acoustic impedance profile for each site was correlated with an analysis (by microscope) of sections taken from that sit...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(95)00025-x

    authors: Tobocman W,Santosh K,Carter JR,Haacke EM

    更新日期:1995-07-01 00:00:00

  • Influence of gas law on ultrasonic behaviour of porous media under pressure.

    abstract::This paper deals with the influence of gas law on ultrasonic behaviour of porous media when the saturating fluid is high pressured. Previous works have demonstrated that ultrasonic transmission through a porous sample with variations of the static pressure (up to 18 bars) of the saturating fluid allows the characteriz...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2010.02.003

    authors: Griffiths S,Ayrault C

    更新日期:2010-06-01 00:00:00

  • Simulation study of a chaotic cavity transducer based virtual phased array used for focusing in the bulk of a solid material.

    abstract::In acoustic and ultrasonic non-destructive testing techniques, it is sometimes beneficial to concentrate sound energy at a chosen location in space and at a specific instance in time, for example to improve the signal-to-noise ratio or activate the nonlinearity of damage features. Time Reversal (TR) techniques, taking...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.01.010

    authors: Delrue S,Van Den Abeele K,Bou Matar O

    更新日期:2016-04-01 00:00:00

  • Solder joint failure localization of welded joint based on acoustic emission beamforming.

    abstract::A localization approach of welded joint damage is proposed based on acoustic emission (AE) beamforming. In this method, a uniform line array is introduced to detect the AE signal of welded joints in specified area. In order to investigate the influence of fillet and crimping commonly existing in a welded plate structu...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.11.002

    authors: Liu X,Xiao D,Shan Y,Pan Q,He T,Gao Y

    更新日期:2017-02-01 00:00:00

  • Lamb waves propagation in elastic plane layers with a joint strip.

    abstract::The Lamb waves are used for the ultrasonic characterization of welds because of their relative long-range propagation. In this paper, a simplified model of a weld-strip between two identical semi-infinite elastic layers is investigated. The reflected and transmitted ultrasonic fields are expressed by modal series whos...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.11.004

    authors: Predoi MV,Rousseau M

    更新日期:2005-06-01 00:00:00

  • Laser-generated surface acoustic waves in a ring-shaped waveguide resonator.

    abstract::Surface acoustic wave (SAW) waveguide resonator is formed by a ring-shaped strip of copper 10 microm wide and approximately 130 microm in diameter embedded into a 0.8 microm thick layer of silica on a silicon wafer. SAWs are excited at one side of the copper ring by a short laser pulse focused into a spatially periodi...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2008.04.007

    authors: Maznev AA

    更新日期:2009-01-01 00:00:00

  • Influence of extrinsic operational parameters on salt diffusion during ultrasound assisted meat curing.

    abstract::The present study investigated the effect of geometric parameters of the ultrasound instrument during meat salting in order to enhance salt diffusion and salt distribution in pork meat on a lab scale. The effects of probe size (∅2.5 and 1.3cm) and of different distances between the transducer and the meat sample (0.3,...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2017.03.017

    authors: Inguglia ES,Zhang Z,Burgess C,Kerry JP,Tiwari BK

    更新日期:2018-02-01 00:00:00

  • Non-contact ultrasonic gas flow metering using air-coupled leaky Lamb waves.

    abstract::This paper describes a completely non-contact ultrasonic method of gas flow metering using air-coupled leaky Lamb waves. To show proof of principle, a simplified representation of gas flow in a duct, comprising two separated thin isotropic plates with a gas flowing between them, has been modelled and investigated expe...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2018.04.008

    authors: Fan Z,Jiang W,Wright WMD

    更新日期:2018-09-01 00:00:00

  • The analysis of the effect of homogeneous mechanical stress on the acoustic wave propagation in the "La3Ga5SiO14/fused silica" piezoelectric layered structure.

    abstract::The results of computer simulation taking into account the linear and nonlinear material constants have been presented. Study of the influence of external uniaxial mechanical stress on the dispersive characteristics of elastic waves in piezoelectric structures as "La3Ga5SiO14/fused silica" has been executed. The compa...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.07.007

    authors: Burkov SI,Zolotova OP,Sorokin BP,Turchin PP

    更新日期:2015-01-01 00:00:00

  • Screen-printed ultrasonic 2-D matrix array transducers for microparticle manipulation.

    abstract::This paper reports the development of a two-dimensional thick film lead zirconate titanate (PZT) ultrasonic transducer array, operating at frequency approximately 7.5MHz, to demonstrate the potential of this fabrication technique for microparticle manipulation. All layers of the array are screen-printed then sintered ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2015.05.010

    authors: Qiu Y,Wang H,Gebhardt S,Bolhovitins A,Démoré CE,Schönecker A,Cochran S

    更新日期:2015-09-01 00:00:00

  • Quantitative colour-ultrasonography by means of a computer aided simultaneous tomogram.

    abstract::In this newly developed method, the ultrasonic diagnosis has become quantitative. The data will remain quantitative so far as an image storage tube is used. With the conventional storage type CRT, it is impossible to memorize the reflected echo signals of different strength levels. But with our method, it becomes poss...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(75)90036-0

    authors: Yokoi H,Tatsumi T,Ito K

    更新日期:1975-09-01 00:00:00

  • Generation of transversal envelope soliton in polymeric and wooden rods.

    abstract::This paper is concerned with the probing of the transversal envelope solitons propagation in circular waveguides when a set of requirements (non-linearity and dispersion) are fulfilled in the waveguide and balanced. The basic idea is to analyze the shape of an acoustic pulse after it has traveled one or few trips thro...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.01.016

    authors: de Billy M,Hladky-Hennion AC

    更新日期:2014-07-01 00:00:00

  • Porosity estimation of concrete by ultrasonic NDE

    abstract::The increasing number of concrete structures with symptoms of premature deterioration due to environmental action demands procedures to estimate the durability of this type of component. Concrete durability is related to porosity, which determines the intensity of interactions of the material with aggressive agents. T...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00095-5

    authors: Hernandez MG,Izquierdo MA,Ibanez A,Anaya JJ,Ullate LG

    更新日期:2000-03-01 00:00:00

  • Surface vibrational modes in disk-shaped resonators.

    abstract::The natural frequencies and distributions of displacement components for the surface vibrational modes in thin isotropic elastic disks are calculated. In particular, the research is focused on even solutions for low-lying resonant vibrations with large angular wave numbers. Several families of modes are found which ar...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.11.002

    authors: Dmitriev AV,Gritsenko DS,Mitrofanov VP

    更新日期:2014-03-01 00:00:00

  • Aperture and element minimization in linear sparse arrays with desired beam patterns

    abstract::In this paper, an optimization method aimed at designing aperiodic linear sparse arrays is proposed that is based on the stochastic optimization methodology called simulated annealing. Such a method optimizes the positions and the weight coefficients of each element of a linear array in order to obtain a beam pattern ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00089-x

    authors: Trucco A

    更新日期:2000-03-01 00:00:00

  • Nitric oxide delivery by ultrasonic cracking: some limitations.

    abstract::Nitric oxide (NO) has been implicated in smooth muscle relaxation. Its use has been widespread in cardiology. Due to the effective scavenging of NO by hemoglobin, however, the drug has to be applied locally or in large quantities, to have the effect desired. We propose the use of encapsulated microbubbles that act as ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.06.003

    authors: Postema M,Bouakaz A,ten Cate FJ,Schmitz G,de Jong N,van Wamel A

    更新日期:2006-12-22 00:00:00

  • Optimizing graphene production in ultrasonic devices.

    abstract::In this work, we investigate the efficiency of graphene production from graphite by ultrasonic-induced exfoliation under different operational conditions. An ultrasonic bath and an ultrasonic horn tip were used, to show how the graphene production efficiency depends on the acoustic intensity and cavitation mechanism u...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.105989

    authors: Silva LI,Mirabella DA,Pablo Tomba J,Riccardi CC

    更新日期:2020-01-01 00:00:00

  • Spatiotemporal mapping of surface acoustic waves in isotropic and anisotropic materials.

    abstract::We demonstrate a new method for a real-time imaging of surface acoustic waves at frequencies up to 1 GHz with picosecond temporal and micron spatial resolutions using an ultrafast optical pump and probe technique combined with a common path interferometer. Using samples with isotropic or anisotropic substrates coated ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(02)00090-2

    authors: Sugawara Y,Wright OB,Matsuda O,Gusev VE

    更新日期:2002-05-01 00:00:00

  • Nondestructive evaluation of steel-concrete composite structure using high-frequency ultrasonic guided wave.

    abstract::Steel-concrete modular construction is increasingly used in nuclear structure construction. Conventional nondestructive testing methods are not able to detect internal concrete defects because the thick concrete wall is covered by steel plates. An ultrasonic guided method is proposed to detect honeycombs and voids aro...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106096

    authors: Sun H,Zhu J

    更新日期:2020-04-01 00:00:00

  • A new beamforming method and hardware architecture for real time two way dynamic depth focusing.

    abstract::The Total Focusing Method (TFM) yields a focused image in emission and in reception while Phased Array (PA) imaging provides Dynamic Depth Focusing (DDF) in reception only. Besides, most NDE applications have two propagation media, where refraction at the interface complicates time-of-flight (TOF) and focal law comput...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.105965

    authors: Cruza JF,Camacho J,Mateos R,Fritsch C

    更新日期:2019-11-01 00:00:00

  • Ultrasonic excitation affects friction interactions between food materials and cutting tools.

    abstract::In the food industry, ultrasonic cutting is used to improve separation by a reduction of the cutting force. This reduction can be attributed to the modification of tool-workpiece interactions at the cutting edge and along the tool flanks because of the superposition of the cutting movement with ultrasonic vibration of...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2009.03.001

    authors: Schneider Y,Zahn S,Schindler C,Rohm H

    更新日期:2009-06-01 00:00:00