Abstract：
:Despite the great potential of Mg and its alloys as material for biodegradable implants, their low resistance to the simultaneous action of corrosion and mechanical stresses in the human body have hampered their use. Stress Corrosion Cracking has been reported as one of the most critical failure modes to overcome to allow such materials to be clinically applied. Thus, in this paper we investigate the effect of Equal Channel Angular Pressing (ECAP) on the Stress Corrosion Cracking (SCC) susceptibility of the AZ31 Mg alloy. To do so, AZ31 alloy has been subjected to 1, 2 and 4 passes of ECAP, and the samples so obtained have then been tested by means Slow Strain Rate Tests (SSRTs) in Simulated Body Fluid (SBF) at 37 °C. Samples subjected to one pass of ECAP are shown to be less susceptible to SCC compared to the material in the as-received condition, while further ECAP processing (2 and 4 passes) are found to worsen the SCC susceptibility. To understand the different SCC susceptibilities shown by the differently ECAPed samples, microstructural analyses, potentiodynamic polarization curves, hydrogen evolution experiments and Scanning Electron Microscopy (SEM) analyses of the fracture surfaces were carried out. The improved corrosion resistance of the samples subjected to 1 pass of ECAP compared to the samples in the as received condition (due to a finer grain size) and to the samples subjected to 2 and 4 passes (due to a more favourable texture evolution) represents the reason of their reduced SCC susceptibility.
journal_name
J Mech Behav Biomed Materauthors
Peron M,Skaret PC,Fabrizi A,Varone A,Montanari R,Roven HJ,Ferro P,Berto F,Torgersen Jdoi
10.1016/j.jmbbm.2020.103724subject
Has Abstractpub_date
2020-06-01 00:00:00pages
103724eissn
1751-6161issn
1878-0180pii
S1751-6161(20)30278-2journal_volume
106pub_type
杂志文章abstract：:The inelastic deformability of the mineralised matrix in bones is critical to their high toughness, but the nanoscale mechanisms are incompletely understood. Antler is a tough bone type, with a nanostructure composed of mineralised collagen fibrils ∼100nm diameter. We track the fibrillar deformation of antler tissue d...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.03.020
更新日期：2013-12-01 00:00:00
abstract：:Due to its proximity to the mitral valve, the coronary sinus (CS) vessel serves as a conduit for the deployment and implantation of the percutaneous transvenous mitral annuloplasty (PTMA) devices that can potentially reduce the mitral regurgitation. Because CS vessel is a venous tissue and seldom diseased, its mechani...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.09.001
更新日期：2012-02-01 00:00:00
abstract：:The objective of this article is to provide an up-to-date overview of zirconia-toughened alumina (ZTA) components used in total hip arthroplasties. The structure, mechanical properties, and available data regarding the clinical performance of ZTA are summarized. The advancements that have been made in understanding th...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章,评审
doi：10.1016/j.jmbbm.2013.03.022
更新日期：2014-03-01 00:00:00
abstract：:Single-cell technologies are powerful tools to evaluate cell characteristics. In particular, Atomic Force Microscopy (AFM) nanoindentation experiments have been widely used to study single cell mechanical properties. One important aspect related to single cell techniques is the need for sufficient statistical power to...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.03.018
更新日期：2019-06-01 00:00:00
abstract：:This study evaluated the effects of two types of superstructures (splinted crown and non-splinted crown) on four vibration characteristics (natural frequency, damping ratio (DAR), vectors in antiphase, maximum displacement (MDP)) by using modal analysis. These structures were fabricated on three implants placed in the...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104050
更新日期：2020-12-01 00:00:00
abstract：:Structure and properties of poly(lactic acid) (PLA)/poly (ɛ-caprolactone) (PCL) influenced by graphite nanoplatelets (GNP) were studied in dependence on blend composition. Electron microscopy indicates predominant localization of GNP in PCL. GNP-induced changes in viscosity hinder refinement of PCL inclusions, support...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.03.028
更新日期：2017-07-01 00:00:00
abstract：:Alterations in mechanical loading can induce growth and remodeling in soft connective tissues. Numerous studies have measured changes in the collagen structure and mechanical properties of cellularized native and engineered tissues in response to cyclic mechanical loading. However, a recent experimental study demonstr...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.03.027
更新日期：2018-06-01 00:00:00
abstract：:The aim of the present work was twofold: to prepare biphasic magnesium fluorapatite (MFA) composites with different amounts of alumina using a two-step sintering process, and to evaluate the effects of various amounts of alumina on the mechanical properties, phase stability, and densification of the composite samples....
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.08.004
更新日期：2014-12-01 00:00:00
abstract：:Meniscal injury is typically treated surgically via partial meniscectomy, which has been shown to cause cartilage degeneration in the long-term. Consequently, research has focused on meniscal prevention and replacement. However, none of the materials or implants developed for meniscal replacement have yet achieved wid...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.06.041
更新日期：2018-10-01 00:00:00
abstract：:A mixture of water/carbon dioxide is a "green" perspective solvent from the viewpoint of biomedical applications. Clathrate hydrates are formed this solvent under certain conditions and a very interesting question is the impact of clathrates hydrates on the structure and properties of bovine pericardium, which is used...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.11.015
更新日期：2017-03-01 00:00:00
abstract：:Mechanical characterization of the cortex of rectrices (tail feathers) of the Toco Toucan (Ramphastos toco) has been carried out by tensile testing of the rachis cortex in order to systematically determine Young's modulus and maximum tensile strength gradients on the surfaces and along the length of the feather. Of ov...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.01.010
更新日期：2011-07-01 00:00:00
abstract：OBJECTIVES:The causes of in vivo fractures of all-ceramic dental crowns are not yet fully understood. The fracture origins often occur in the cervical margin in the approximal area, but the reason for this is unclear. The aim of this study was to evaluate the fracture origin of 22 of clinically-failed alumina crowns. ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.08.006
更新日期：2016-01-01 00:00:00
abstract：:Constitutive models for biological tissue are typically formulated as a mixture of constituents and the overall response is then assembled by superposition or compatibility. This ensures the stress response of the biological tissue to be in the range of a given constitutive relationship, guaranteeing that at least one...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.04.037
更新日期：2019-08-01 00:00:00
abstract：:In order to improve the osteogenic activity and mechanical strength of the guided bone regeneration (GBR) membrane for repairing bone defect, nano-hydroxyapatite/chitosan (nHA/CS) composite microspheres were prepared through in situ biomimetic method, then composite microspheres were incorporated into CS membrane. The...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.03.006
更新日期：2018-05-01 00:00:00
abstract：:The objective of this study was to develop a nanoscratch technique that can be used to measure the in situ toughness of bone at micro/nanostructural levels. Among the currently possible techniques, the surface scratch test may be conducted on very small regions, thus exhibiting a potential in determining the in situ f...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.08.019
更新日期：2012-01-01 00:00:00
abstract：AIM:For the proper function of small diameter vascular grafts their mechanical properties are essential. A variety of testing methods and protocols exists to measure tensile strength, compliance and viscoelastic material behavior. In this study the impact of the measurement protocol in hoop tensile tests on the measure...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103652
更新日期：2020-04-01 00:00:00
abstract：:Tooth dentine and other bone-like materials contain carbonated hydroxyapatite nanoparticles within a network of collagen fibrils. It is widely assumed that the elastic properties of biogenic hydroxyapatites are identical to those of geological apatite. By applying hydrostatic pressure and by in situ measurements of th...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.06.005
更新日期：2015-10-01 00:00:00
abstract：:The passive micro-structural mechanical response of muscle tissue is important for numerous medical applications. However, the recently observed tension/compression asymmetry in porcine muscle remains poorly explained. In particular there remains a lack of understanding of how external tension or compression applied i...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.08.019
更新日期：2014-12-01 00:00:00
abstract：:Vascular calcification is a complex molecular process that exhibits a number of relatively characteristic morphology patterns in atherosclerotic plaques. Treatment of arterial stenosis by endovascular intervention, involving forceful circumferential expansion of the plaque, can be unpredictable in calcified lesions. T...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.11.001
更新日期：2016-03-01 00:00:00
abstract：OBJECTIVE:This study examined the effect of phytic acid (IP6) in stabilizing the morphology of dentine collagen network and resin-dentine bonding. METHODS:Dentine beams were fully demineralized with 10% phosphoric acid (PA) or 1% IP6 (pH 1.2). PA-demineralized beams were divided into three groups: (a) no further treat...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.03.027
更新日期：2015-08-01 00:00:00
abstract：:Polycarbonate polyurethane has cartilage-like, hygroscopic, and elastomeric properties that make it an attractive material for orthopedic joint replacement application. However, little data exists on the cyclic loading and fracture behavior of polycarbonate polyurethane. This study investigates the mechanisms of fatig...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.01.008
更新日期：2018-03-01 00:00:00
abstract：:This study aims to evaluate the flexural fatigue strength and survival estimates of an Y-TZP monolithic ceramic after grinding and aging. Ceramic discs (1.2 mm thickness × 15.0 mm diameter - ISO, 6872, 2015) of zirconia (Zirlux FC2 - Ardent; Ivoclar Vivadent) were made and randomly allocated into 6 groups (n = 10), ac...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.07.041
更新日期：2018-11-01 00:00:00
abstract：:An optimized thickness of a transplantable auricular silicone scaffold was researched. The original image data were acquired from CT scans, and reverse modeling technology was used to build a digital 3D model of an auricle. The transplant process was simulated in ANSYS Workbench by finite element analysis (FEA), solid...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.08.032
更新日期：2016-01-01 00:00:00
abstract：:Characterization of the mechanical properties of biological materials is often complicated by small volume, irregular geometry, fragility, and environmental sensitivity. Pipette aspiration and nanoindentation testing deal well with these limitations and have seen increasing use in biomaterial characterization, but lit...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.07.022
更新日期：2015-11-01 00:00:00
abstract：:Modeling human body response to dynamic loading events and developing biofidelic human surrogate systems require accurate material properties over a range of loading rates for various human organ tissues. This work describes a technique for measuring the shear properties of soft biomaterials at high rates of strain (1...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.06.008
更新日期：2011-11-01 00:00:00
abstract：:Osteoporosis can lead to bone compressive fractures in the lower lumbar vertebrae. In order to assess the recovery of vertebral strength during drug treatment for osteoporosis, it is necessary not only to measure the bone mass but also to perform patient-specific mechanical analyses, since the strength of osteoporotic...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2009.03.001
更新日期：2010-01-01 00:00:00
abstract：:In this study, Polylactic acid (PLA)/phosphate glass fibres (PGF) composites were prepared by compression moulding. Fibres produced from phosphate based glasses P2O5-CaO-MgO-Na2O (P45B0), P2O5-CaO-MgO-Na2O-B2O3 (P45B5), P2O5-CaO-MgO-Na2O-Fe2O3 (P45Fe3) and P2O5-CaO-MgO-Na2O-B2O3-Fe2O3 (P45B5Fe3) were used to reinforce...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.12.011
更新日期：2016-06-01 00:00:00
abstract：:Many treatments for cardiovascular diseases include an endovascular insertion of stents or stent grafts into arteries, a procedure which may cause high tissue stresses and even damage in the arterial wall. In order to study such problems by using finite element methods, both appropriate constitutive models and experim...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2012.03.012
更新日期：2012-08-01 00:00:00
abstract：:According to the literature, there are many mathematical relationships between density of the trabecular bone and mechanical properties obtained in macro-scale testing. In micro-scale, the measurements provide only the ranges of Young׳s modulus of trabeculae, but there are no experimentally tested relationships allowi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.04.011
更新日期：2014-08-01 00:00:00
abstract：:Core decompression is a minimally invasive surgical technique used to treat patients with avascular necrosis of the femoral head. The procedure requires an entry hole in the lateral cortex of the femur which potentially leaves patients susceptible to subtrochanteric fractures. The purpose of this study was to determin...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104263
更新日期：2021-03-01 00:00:00
