Abstract：
:A technique was developed to investigate the condylar displacement of the human temporomandibular joint. Condylar displacement was analyzed from magnetic resonance images of the joint. Fourteen static images were obtained during incremental jaw closure. Landmarks were identified on the magnetic resonance images and reference points were digitized. The condylar displacement was calculated based on an optimization algorithm. The technique was proven to be reproducible based on two feasibility tests. The results provided quantitative descriptions of the condylar displacement as a function of a prescribed jaw movement. The displacement was characterized by a translation of an anatomical point on the condyle and a rotation of the mandible. The condylar displacement was 6 mm at a mouth opening of 17 mm. Maximum rotation of the mandible was 12.3 degrees C. The motion of the condyle produced by the mechanical guidance system used in this study may be characterized as a small forward translation at the beginning of jaw opening, followed by a combination of translation and rotation.
journal_name
J Biomechjournal_title
Journal of biomechanicsauthors
Chen J,Buckwalter Kdoi
10.1016/0021-9290(93)90096-wsubject
Has Abstractpub_date
1993-12-01 00:00:00pages
1455-62issue
12eissn
0021-9290issn
1873-2380pii
0021-9290(93)90096-Wjournal_volume
26pub_type
杂志文章abstract：:In presence of aortic stenosis, a jet is produced downstream of the aortic valve annulus during systole. The vena contracta corresponds to the location where the cross-sectional area of the flow jet is minimal. The maximal transvalvular pressure gradient (TPG(max)) is the difference between the static pressure in the ...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2005.10.013
更新日期：2006-01-01 00:00:00
abstract：:A method for measuring three-dimensional kinematics that incorporates the direct cross-registration of experimental kinematics with anatomic geometry from Computed Tomography (CT) data has been developed. Plexiglas registration blocks were attached to the bones of interest and the specimen was CT scanned. Computer mod...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(00)00195-0
更新日期：2001-03-01 00:00:00
abstract：:This article describes a method to simulate fusion of morselized cancellous bone. The morselized cancellous bone is mixed with an epoxy adhesive, in empirically determined proportions. The mixture is then impacted into a construct. When the epoxy cures, the morselized material fuses into a cohesive, contiguous structu...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(01)00032-x
更新日期：2001-06-01 00:00:00
abstract：:The critical role that mechanical stimuli serve in mediating bone repair is recognized but incompletely understood. Further, previous attempts to understand this role have utilized application of externally applied mechanical loads to study the tissue's response. In this project, we have therefore endeavored to capita...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2010.06.030
更新日期：2010-10-19 00:00:00
abstract：:A device is described for measuring strength and power outputs of dynamic vertical lifts between heights of 0.4 and 2.2 m. The device is safe, robust, and easily transportable. It consists of a water-filled tube 2 m high and 200 mm internal diameter. The subject pulls vertically on a handle which is connected with fle...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(96)00155-8
更新日期：1997-04-01 00:00:00
abstract：:Increased knee flexion during stance is a common gait deviation in the child with cerebral palsy (CP), with distal hamstring lengthening surgeries being an accepted course of treatment. Post-operatively, improvements in gait kinematics have been reported, however little change is noted in the patterns of muscle activi...
journal_title：Journal of biomechanics
pub_type： 临床试验,杂志文章
doi：10.1016/j.jbiomech.2007.01.001
更新日期：2007-01-01 00:00:00
abstract：:Tripping over obstacles is the most frequently mentioned causes of falls. Thus, this study was performed to test the hypotheses that when crossing obstacles, toe-obstacle clearance and the three-dimensional motions and moments at the hip, knee, and ankle of the trailing limb (limb crossing the obstacle last) increase ...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(96)00161-3
更新日期：1997-04-01 00:00:00
abstract：:In finite element (FE) models knee ligaments can represented either by a group of one-dimensional springs, or by three-dimensional continuum elements based on segmentations. Continuum models closer approximate the anatomy, and facilitate ligament wrapping, while spring models are computationally less expensive. The me...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2017.08.030
更新日期：2017-12-08 00:00:00
abstract：:This study investigated the center of rotation (COR) of the intervertebral segments of the lower lumbar spine (L4-L5 and L5-S1 segments) in sagittal plane during a weight-lifting (3.6 kg in each hand) extension activity performed with the pelvis constrained. Seven healthy subjects were studied using a dual fluoroscopi...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2015.12.029
更新日期：2016-02-08 00:00:00
abstract：:Nanoindentation has been widely used as a means to measure the micro-mechanical properties of bone and to predict the macroscopic properties. The role of indent depth and indenter tip geometry in measuring the hierarchical properties of bone tissue was explored experimentally using a range of spherical indenter tips o...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2010.10.008
更新日期：2011-01-11 00:00:00
abstract：:In order to provide physical information supporting the clinical use of flow mapping, an in vitro model was designed to measure the velocity fields in a pulsatile hydraulic turbulent jet. We used a peak velocity ranging from 2.5 to 5.5 m.s-1, an orifice diameter ranging from 5.8 to 11.3 mm and confined the jet in a re...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/0021-9290(90)90367-c
更新日期：1990-01-01 00:00:00
abstract：:The drop vertical jump (DVJ) task is commonly used to assess biomechanical performance measures that are associated with ACL injury risk in athletes. Previous investigations have solely assessed the first landing phase. We examined the first and second landings of a DVJ for differences in the magnitude of vertical gro...
journal_title：Journal of biomechanics
pub_type： 临床试验,杂志文章
doi：10.1016/j.jbiomech.2013.02.024
更新日期：2013-04-26 00:00:00
abstract：:The oxidized low-density lipoprotein (Ox-LDL) plays an important role in atherosclerosis, yet it remains unclear if it damages circulating erythrocytes. In this study, erythrocyte deformability and its membrane proteins after Ox-LDL incubations are investigated by micropipette aspiration, thiol radical measurement, an...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2009.05.026
更新日期：2009-10-16 00:00:00
abstract：:In this paper we introduce the concept of the functional (or equivalent) geometry of the knee, which is an attempt to reduce the natural knee with its complex geometry, frictional resistance and deformable cartilage into a two-dimensional joint comprising rigid femur and tibia in frictionless contact. An apparatus and...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(98)00141-9
更新日期：1999-01-01 00:00:00
abstract：:Refractures and secondary fractures occur after removal of internal fixation devices even when the X-rays show well-mineralized bony unions. This indicates the unreliability of bone density as the only parameter to estimate the strength of healing bone. The aim of this study was to show that the strength of healing bo...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/0021-9290(95)00006-4
更新日期：1995-11-01 00:00:00
abstract：:We proposed a velocity control strategy for dynamic posture determination that underlay an optimization-based differential inverse kinematics (ODIK) approach for modeling three-dimensional (3-D) seated reaching movements. In this modeling approach, a four-segment seven-DOF linkage is employed to represent the torso an...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(98)00117-1
更新日期：1998-11-01 00:00:00
abstract：:Osteoporosis is a widely spread disease with severe consequences for patients and high costs for health care systems. The disease is characterised by a loss of bone mass which induces a loss of mechanical performance and structural integrity. It was found that transverse trabeculae are thinned and perforated while ver...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2009.06.017
更新日期：2009-09-18 00:00:00
abstract：:Side-cutting is commonly used to evaluate knee joint kinematics and kinetics in the context of anterior cruciate ligament injury risk. Many existing side-cutting studies fail to clearly define the orientation of the femoral frame and the knee axis, making comparisons between studies difficult. A femoral frame construc...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2012.05.017
更新日期：2012-07-26 00:00:00
abstract：:Bilateral asymmetry in gallop stride limb contact patterns of four Quarter Horse fillies was documented by high-speed cinematography. Horses were filmed with rider by two cameras simultaneously while galloping along a straightaway. Even though signaled for each gallop lead an equivalent number of times, horses frequen...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/0021-9290(87)90285-5
更新日期：1987-01-01 00:00:00
abstract：:Bone is a dynamic tissue which, through the process of bone remodeling in the mature skeleton, renews itself during normal function and adapts to mechanical loads. It is, therefore, important to understand the effect of remodeling on the mechanical function of bone, as well as the effect of the inherent time lag in th...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(00)00221-9
更新日期：2001-03-01 00:00:00
abstract：:The three-dimensional trajectory of the body's centre of mass (COM) is useful to determine a number of biomechanical outcomes in running research. Previous studies have used the COM to calculate measures such as overstriding, vertical stiffness, and vertical oscillation. The COM is traditionally computed using the seg...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2020.109886
更新日期：2020-07-17 00:00:00
abstract：:This communication extends the recently reported cell-specific finite element (FE) method in Slomka and Gefen (2010) in which geometrically realistic FE cell models are created from confocal microscopy scans for large deformation analyses. The cell-specific FE method is extended here in the following aspects: (i) we d...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2010.09.012
更新日期：2011-02-03 00:00:00
abstract：:The purpose of this study was to investigate the mechanical consequences of proteoglycan 4 (Prg4) deficiency on intervertebral disc mechanics using a Prg4 knockout mouse model. Prg4, also called lubricin, was first identified as the boundary lubricant in synovial fluid but has subsequently been localized within a numb...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2015.03.029
更新日期：2015-07-16 00:00:00
abstract：:The advent of microelectromechanical systems (MEMS) sensors has enabled real-time wall shear stress (WSS) measurements with high spatial and temporal resolution in a 3-D bifurcation model. To optimize intravascular shear stress assessment, we evaluated the feasibility of catheter/coaxial wire-based MEMS sensors in the...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2009.04.021
更新日期：2009-07-22 00:00:00
abstract：:The aim of this study is to investigate the biomechanics for orthodontic tooth movement (OTM) subjected to concurrent single-tooth vibration (50Hz) with conventional orthodontic force application, via a clinical study and computational simulation. Thirteen patients were recruited in the clinical study, which involved ...
journal_title：Journal of biomechanics
pub_type： 杂志文章,随机对照试验
doi：10.1016/j.jbiomech.2017.06.012
更新日期：2017-07-26 00:00:00
abstract：:High-energy synchrotron X-ray scattering (>60 keV) allows noninvasive quantification of internal strains within bone. In this proof-of-principle study, wide angle X-ray scattering maps internal strain vs position in cortical bone (murine tibia, bovine femur) under compression, specifically using the response of the mi...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2010.10.015
更新日期：2011-01-11 00:00:00
abstract：:An aortic aneurysm is defined as a balloon-shaped bulging of all three histologic components of the aortic vessel walls (intima, media and adventitia). This dilation results from vessel weakening owing to remodeling, i.e. due to cystic degeneration of the Tunica media (Marfan), progression of atherosclerosis or presen...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2018.05.033
更新日期：2018-07-25 00:00:00
abstract：:Diurnal disc height changes, due to fluid in- and outflow, are in equilibrium while daytime spinal loading is twice as long as night time rest. A direction-dependent permeability of the endplates, favouring inflow over outflow, reportedly explains this; however, fluid flow through the annulus fibrosus should be consid...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/j.jbiomech.2015.11.041
更新日期：2016-04-11 00:00:00
abstract：:Adhesions of monocytes and platelets to a vascular surface, particularly in regions of flow stagnation, recirculation, and reattachment, are a significant initial event in a broad spectrum of particle-wall interactions that significantly influence the formation of stenotic lesions and mural thrombi. A number of approx...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/s0021-9290(02)00434-7
更新日期：2003-03-01 00:00:00
abstract：:The second part of this study of the six axes of head motion caused by translational seat vibration is concerned with the effect of fore-and-aft (x-axis) and lateral (y-axis) seat vibration. Seat-to-head transmissibilities have been determined at frequencies up to 16 Hz for each of the three translational and three ro...
journal_title：Journal of biomechanics
pub_type： 杂志文章
doi：10.1016/0021-9290(88)90170-4
更新日期：1988-01-01 00:00:00
