当前位置： SCI文献检索 > Journal of the Mechanical Behavior of Biomedical Materials期刊下所有文献 > Crack initiation from a clinically relevant notch in a highly-crosslinked UHMWPE subjected to static and cyclic loading.

Crack initiation from a clinically relevant notch in a highly-crosslinked UHMWPE subjected to static and cyclic loading.

Abstract：

:Crosslinked Ultra High Molecular Weight Polyethylene (UHMWPE), which is used as a bearing material in total joint replacement components, is subjected to static and cyclic loads in vivo. Resistance to crack initiation from a notch as a function of static and cyclic loads is not well understood for crosslinked UHMWPE. This study estimated the resistance of crosslinked UHMWPE (crosslinked with 100 kGy gamma radiation and remelted to extinguish free radicals) to crack initiation for a clinically relevant notch under both static and cyclic loading conditions. For cyclic loading, four frequencies were applied with a sine waveform and two frequencies were applied with a square waveform to independently estimate the effect of frequency and rate of loading on crack initiation. Crack initiation time and cycles to crack initiation were determined. Crack initiation time for fatigue loading conditions was substantially lower compared to static loading conditions. Crack initiation time decreased with an increase in test frequency. A square wave resulted in shorter crack initiation time compared to a sine wave. The results suggest that crosslinked UHMWPE is more resistant to crack initiation from a notch under static loading conditions compared to fatigue loading conditions.

journal_name

J Mech Behav Biomed Mater

journal_title

Journal of the mechanical behavior of biomedical materials

authors

Sirimamilla A,Rimnac CM

doi

10.1016/j.jmbbm.2018.12.032

subject

Has Abstract

pub_date

2019-03-01 00:00:00

pages

366-372

eissn

1751-6161

issn

1878-0180

pii

S1751-6161(18)31186-X

journal_volume

91

pub_type

杂志文章

相关文献

Journal of the Mechanical Behavior of Biomedical Materials文献大全
  • Assessment of a long-term in vitro model to characterize the mechanical behavior and macrophage-mediated degradation of a novel, degradable, electrospun poly-urethane vascular graft.

    abstract：:An assessment tool to evaluate the degradation of biodegradable materials in a more physiological environment is still needed. Macrophages are critical players in host response, remodeling and degradation. In this study, a cell culture model using monocyte-derived primary macrophages was established to study the degra...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.104077

    authors： Enayati M,Puchhammer S,Iturri J,Grasl C,Kaun C,Baudis S,Walter I,Schima H,Liska R,Wojta J,Toca-Herrera JL,Podesser BK,Bergmeister H

    更新日期：2020-12-01 00:00:00

  • Mechanical characterization of bio composite films as a novel drug carrier platform for sustained release of 5-fluorouracil for colon cancer: Methodological investigation.

    abstract：:In this study, we employed Pectin (PC) as a matrix that is hybridized with three different nucleobase (NB) units (cytosine, thymine, uracil) to generate pectin-nucleobase(PC-NB) biocomposite films stabilized through bio-multiple hydrogen bonds (BMHBs) as drug carrier for anticancer 5-Fluorouracil (5-FU). Prepared bioc...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.104266

    authors： Tamilselvi S,Kavitha R,Usharani M,Mumjitha M,Mohanapriya S,MohanaPriya S

    更新日期：2021-03-01 00:00:00

  • Mechanical properties and electrochemical behavior of porous Ti-Nb biomaterials.

    abstract：:Ti-Nb-based alloys - with their superior mechanical properties and biocompatibility - are attractive biomaterials for orthopedic implants. By producing this alloys with a porous structure, it is possible to achieve mechanical properties similar to that of bone and to facilitate cellular activities. In this study, Ti16...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.07.018

    authors： Yılmaz E,Gökçe A,Findik F,Gulsoy HO,İyibilgin O

    更新日期：2018-11-01 00:00:00

  • Periprosthetic wear particle migration and distribution modelling and the implication for osteolysis in cementless total hip replacement.

    abstract：:In total hip replacement (THR), wear particles play a significant role in osteolysis and have been observed in locations as remote as the tip of femoral stem. However, there is no clear understanding of the factors and mechanisms causing, or contributing to particle migration to the periprosthetic tissue. Interfacial ...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2014.01.005

    authors： Alidousti H,Taylor M,Bressloff NW

    更新日期：2014-04-01 00:00:00

  • Effect of fluorine substitution on sintering behaviour, mechanical and bioactivity of hydroxyapatite.

    abstract：:Fluorine substituted hydroxyapatite (FAp) with different degree of fluorine (F) substitution, has been synthesized using hydrothermal synthesis method. In the present work, as synthesized powders were consolidated by sintering at 1200 °C in air for 1 h. The sintered specimens were characterized using Fourier transform...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.03.032

    authors： Nasker P,Samanta A,Rudra S,Sinha A,Mukhopadhyay AK,Das M

    更新日期：2019-07-01 00:00:00

  • Material property discontinuities in intervertebral disc porohyperelastic finite element models generate numerical instabilities due to volumetric strain variations.

    abstract：:Numerical studies of the intervertebral disc (IVD) are important to better understand the load transfer and the mechanobiological processes within the disc. Among the relevant calculations, fluid-related outputs are critical to describe and explore accurately the tissue properties. Porohyperelastic finite element mode...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2013.05.012

    authors： Ruiz C,Noailly J,Lacroix D

    更新日期：2013-10-01 00:00:00

  • Damage initiation and progression in the cartilage surface probed by nonlinear optical microscopy.

    abstract：:With increasing interest in treating osteoarthritis at its earliest stages, it has become important to understand the mechanisms by which the disease progresses across a joint. Here, second harmonic generation (SHG) microscopy, coupled with a two-dimensional spring-mass network model, was used to image and investigate...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2011.08.004

    authors： Brown CP,Houle MA,Chen M,Price AJ,Légaré F,Gill HS

    更新日期：2012-01-01 00:00:00

  • On multiscale boundary conditions in the computational homogenization of an RVE of tendon fascicles.

    abstract：:Present study provides a numerical investigation on multiscale boundary conditions in the computational homogenization of a representative volume element (RVE) of tendon fascicles. A three-dimensional hexagonal-helicoidal finite element RVE composed of two material phases (collagen fibers and cells) and three finite s...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.12.003

    authors： Carniel TA,Klahr B,Fancello EA

    更新日期：2019-03-01 00:00:00

  • A low-shrinkage dental composite with epoxy-polyhedral oligomeric silsesquioxane.

    abstract：:Polymerization shrinkage and mechanical properties affect the service life of dental restorative composites. Polyhedral oligomeric silsesquioxanes (POSS) can be an efficient strategy to improve the shrinkage properties and mechanical properties simultaneously. In this work, epoxycyclohexyl POSS (E-POSS) was used to mo...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103515

    authors： Li Z,Zhang H,Xiong G,Zhang J,Guo R,Li L,Zhou H,Chen G,Zhou Z,Li Q

    更新日期：2020-03-01 00:00:00

  • Analysis of the mechanical response of biomimetic materials with highly oriented microstructures through 3D printing, mechanical testing and modeling.

    abstract：:Many biomineralized organisms have evolved highly oriented nanostructures to perform specific functions. One key example is the abrasion-resistant rod-like microstructure found in the radular teeth of Chitons (Cryptochiton stelleri), a large mollusk. The teeth consist of a soft core and a hard shell that is abrasion r...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.03.026

    authors： de Obaldia EE,Jeong C,Grunenfelder LK,Kisailus D,Zavattieri P

    更新日期：2015-08-01 00:00:00

  • On the necessity of modelling fluid-structure interaction for stented coronary arteries.

    abstract：:Although stenting is the most commonly performed procedure for the treatment of coronary atherosclerotic lesions, in-stent restenosis (ISR) remains one of the most serious clinical complications. An important stimulus to ISR is the altered hemodynamics with abnormal shear stresses on endothelial cells generated by the...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2014.02.009

    authors： Chiastra C,Migliavacca F,Martínez MÁ,Malvè M

    更新日期：2014-06-01 00:00:00

  • A new longitudinal variation in the structure of collagen fibrils and its relationship to locations of mechanical damage susceptibility.

    abstract：:The hierarchical architecture of the collagen fibril is well understood, involving non-integer staggering of collagen molecules which results in a 67 nm periodic molecular density variation termed D-banding. Other than this variation, collagen fibrils are considered to be homogeneous at the micro-scale and beyond. Int...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2020.103849

    authors： Baldwin SJ,Sampson J,Peacock CJ,Martin ML,Veres SP,Lee JM,Kreplak L

    更新日期：2020-10-01 00:00:00

  • Biocompatibility and compressive properties of Ti-6Al-4V scaffolds having Mg element.

    abstract：:Porous scaffolds of Ti-6Al-4V were produced by mixing of this alloy with different amount of magnesium (Mg) powders. The mixtures were compacted in steel die by applying uniaxial pressure of 500 MPa before sintering the compacts in sealed quartz tubes at 900 °C for 2 h. Employing Archimedes׳ principle and Image Tool s...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.04.015

    authors： Kalantari SM,Arabi H,Mirdamadi S,Mirsalehi SA

    更新日期：2015-08-01 00:00:00

  • Clamping soft biologic tissues for uniaxial tensile testing: A brief survey of current methods and development of a novel clamping mechanism.

    abstract：:Biologic tissues are complex materials that come in many forms and perform a variety of functions. They vary widely in composition and mechanical properties, and determination of the mechanical properties of tissues is of interest to those trying to engineer tissues to restore missing function. In performing experimen...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103503

    authors： Jiang M,Lawson ZT,Erel V,Pervere S,Nan T,Robbins AB,Feed AD,Moreno MR

    更新日期：2020-03-01 00:00:00

  • The impact of metastasis on the mineral phase of vertebral bone tissue.

    abstract：:The negative impact of metastases on the mechanical performance of vertebral bone is often attributed to reduced bone density and/or compromised architecture. However limited characterization has been done on the impact of metastasis on the mineralization of bone tissue and resulting changes in material behaviour. Thi...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.12.017

    authors： Burke M,Atkins A,Kiss A,Akens M,Yee A,Whyne C

    更新日期：2017-05-01 00:00:00

  • Cervical fusion cage computationally optimized with porous architected Titanium for minimized subsidence.

    abstract：:Anterior cervical discectomy with fusion is a common surgical treatment that can relieve patients suffering from cervical spondylosis. This surgery is most commonly performed with the use of a cervical cage. One serious complication of the fusion cages commercially available in the market is subsidence of the cage wit...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.05.040

    authors： Moussa A,Tanzer M,Pasini D

    更新日期：2018-09-01 00:00:00

  • Microstructure and mechanical properties of MgO-stabilized ZrO₂-Al₂O₃ dental composites.

    abstract：:The aim of the present study was to investigate the production of tetragonal zirconia (t-ZrO(2)) particles (experimental t-ZrO(2)) from monoclinic zirconia (m-ZrO(2)) and to evaluate the effect of the t-ZrO(2) content on the fracture toughness of alumina-zirconia composites by conducting ASTM E399 standard test. In th...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2012.11.007

    authors： Abi CB,Emrullahoğlu OF,Said G

    更新日期：2013-02-01 00:00:00

  • Through-thickness stress relaxation in bacterial cellulose hydrogel.

    abstract：:Biological hydrogels, e.g. bacterial cellulose (BC) hydrogel, attracted increasing interest in recent decades since they show a good potential for biomedical engineering as replacements of real tissues thanks mainly to their good biocompatibility and fibrous structure. To select potential candidates for such applicati...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.12.021

    authors： Gao X,Kuśmierczyk P,Shi Z,Liu C,Yang G,Sevostianov I,Silberschmidt VV

    更新日期：2016-06-01 00:00:00

  • Finite Element simulation of buckling-induced vein tortuosity and influence of the wall constitutive properties.

    abstract：:The mechanisms giving rise to vein tortuosity, which is often associated with varicosis, are poorly understood. Recent works suggest that significant biological changes in the wall of varicose veins may precede the mechanical aspects of the disease. To test the hypothesis of tortuosity being a consequence of these cha...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2013.05.006

    authors： Badel P,Rohan CP,Avril S

    更新日期：2013-10-01 00:00:00

  • Adhesion failure behavior of sputtered calcium phosphate thin film coatings evaluated using microscratch testing.

    abstract：:It is generally accepted that calcium phosphate (CaP) is one of the most important biomaterials in implant coating applications mainly because of its excellent bioactivity. However, its relatively poor mechanical properties limits its application. This entails that a better understanding of the mechanical properties o...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2010.01.002

    authors： Toque JA,Herliansyah MK,Hamdi M,Ide-Ektessabi A,Sopyan I

    更新日期：2010-05-01 00:00:00

  • Compliance mismatch and compressive wall stresses drive anomalous remodelling of pulmonary trunks reinforced with Dacron grafts.

    abstract：:Synthetic grafts are often satisfactory employed in cardiac and vascular surgery, including expanded poly(ethylene terephthalate) or expanded poly(tetrafluoroethylene). However, accumulating evidences suggest the emergence of worrisome issues concerning the long-term fate of prosthetic grafts as large vessel replaceme...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2016.06.023

    authors： Nappi F,Carotenuto AR,Cutolo A,Fouret P,Acar C,Chachques JC,Fraldi M

    更新日期：2016-10-01 00:00:00

  • Administration of PTH and ibandronate increases ovariectomized rat compact bone viscoelasticity.

    abstract：:In this study, the bone mineral density (BMD), geometry, macroscopic viscoelastic properties and mechanical strength in five different groups of Sprague-Dawley rats (sham operated, ovariectomized with vehicle, parathyroid hormone and/or ibandronate administration) were examined by peripheral quantitative computed tomo...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2013.03.009

    authors： Yang X,Teoh SH,DasDe S,Lee T

    更新日期：2013-06-01 00:00:00

  • Microstructure, mechanical property and metal release of As-SLM CoCrW alloy under different solution treatment conditions.

    abstract：:In the study, the microstructure, mechanical property and metal release behavior of selective laser melted CoCrW alloys under different solution treatment conditions were systemically investigated to assess their potential use in orthopedic implants. The effects of the solution treatment on the microstructure, mechani...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.10.019

    authors： Lu Y,Wu S,Gan Y,Zhang S,Guo S,Lin J,Lin J

    更新日期：2015-03-01 00:00:00

  • Effect of alumina contents on phase stability and mechanical properties of magnesium fluorapatite/alumina composites.

    abstract：:The aim of the present work was twofold: to prepare biphasic magnesium fluorapatite (MFA) composites with different amounts of alumina using a two-step sintering process, and to evaluate the effects of various amounts of alumina on the mechanical properties, phase stability, and densification of the composite samples....

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2014.08.004

    authors： Hejazi MS,Ahmadian M,Meratian M,Fathi MH

    更新日期：2014-12-01 00:00:00

  • Effect of cell sample size in atomic force microscopy nanoindentation.

    abstract：:Single-cell technologies are powerful tools to evaluate cell characteristics. In particular, Atomic Force Microscopy (AFM) nanoindentation experiments have been widely used to study single cell mechanical properties. One important aspect related to single cell techniques is the need for sufficient statistical power to...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.03.018

    authors： Marcotti S,Reilly GC,Lacroix D

    更新日期：2019-06-01 00:00:00

  • A study of extracellular matrix remodeling in aortic heart valves using a novel biaxial stretch bioreactor.

    abstract：:In aortic valves, biaxial cyclic stretch is known to modulate cell differentiation, extracellular matrix (ECM) synthesis and organization. We designed a novel bioreactor that can apply independent and precise stretch along radial and circumferential directions in a tissue culture environment. While this bioreactor can...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2017.07.041

    authors： Lei Y,Masjedi S,Ferdous Z

    更新日期：2017-11-01 00:00:00

  • Modeling ultrasonic wave propagation in a dental implant - Bone system.

    abstract：:The evolution of the bone-implant interface reflects the implant osseointegration and bond strength, thereby determining the overall implant stability in the jawbone. Quantitative ultrasound represents a promising alternative technique to characterize the interfacial integrity, precisely due to the fact that those wav...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2019.103547

    authors： Dorogoy A,Haïat G,Shemtov-Yona K,Rittel D

    更新日期：2020-03-01 00:00:00

  • Effect of grinding with diamond-disc and -bur on the mechanical behavior of a Y-TZP ceramic.

    abstract：:This study compared the effects of grinding on the surface micromorphology, phase transformation (t→m), biaxial flexural strength and structural reliability (Weibull analysis) of a Y-TZP (Lava) ceramic using diamond-discs and -burs. 170 discs (15×1.2mm) were produced and divided into 5 groups: without treatment (Ctrl,...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2014.05.010

    authors： Pereira GK,Amaral M,Simoneti R,Rocha GC,Cesar PF,Valandro LF

    更新日期：2014-09-01 00:00:00

  • Quantitative/qualitative analysis of adhesive-dentin interface in the presence of 10-methacryloyloxydecyl dihydrogen phosphate.

    abstract：:Dental adhesive provides effective retention of filling materials via adhesive-dentin hybridization. The use of co-monomers, such as 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP), is thought to be crucial for hybridization owing to their ionic-binding to calcium and co-polymerization in the polymerizable adhe...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2018.12.038

    authors： Zhou J,Wurihan,Shibata Y,Tanaka R,Zhang Z,Zheng K,Li Q,Ikeda S,Gao P,Miyazaki T

    更新日期：2019-04-01 00:00:00

  • Mechanical characterization and modelling of the temperature-dependent impact behaviour of a biocompatible poly(L-lactide)/poly(ε-caprolactone) polymer blend.

    abstract：:Poly(ε-caprolactone) (PCL) is a ductile, bioabsorbable polymer that has been employed as a blend partner for poly(L-lactic acid) (PLLA). An improvement of the material strength and impact resistance of PLLA/PCL polymer blends compared to pure PLLA has been shown previously. To use numerical simulations in the design p...

    journal_title：Journal of the mechanical behavior of biomedical materials

    pub_type： 杂志文章

    doi：10.1016/j.jmbbm.2015.07.007

    authors： Gustafsson G,Nishida M,Ito Y,Häggblad HÅ,Jonsén P,Takayama T,Todo M

    更新日期：2015-11-01 00:00:00