Effect of adhesive primer developed exclusively for heat-curing resin on adhesive strength between plastic artificial tooth and acrylic denture base resin.

abstract：:This study investigated the effects of spherical silica fillers on the physical and mechanical properties of resin-modified glass-ionomer cement (RMGIC). Specimens were fabricated by mixing untreated (UF) or silanized (SF) spherical silica filler into the powder of a commercially prepared RMGIC. The original RMGIC and...

journal_title：Dental materials journal

authors： Tjandrawinata R,Irie M,Yoshida Y,Suzuki K

更新日期：2004-06-01 00:00:00

abstract：:This study aimed to evaluate influence of different post-end positions in alveolar bone level on stress distributions in resin-core build-up tooth under different load directions. Three-dimensional mathematical models of a root-filled mandibular premolar tooth were constructed. Resin post and core were built-up with s...

journal_title：Dental materials journal

authors： Hatayama T,Chiba A,Kainose K,Nakajima M,Hosaka K,Wakabayashi N,Foxton RM,Tagami J

更新日期：2018-06-08 00:00:00

abstract：:To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding gro...

journal_title：Dental materials journal

authors： Kusunoki M,Itoh K,Takahashi Y,Hisamitsu H

更新日期：2006-09-01 00:00:00

abstract：:The aim of this study was to investigate the relationship between the different mechanical properties with the filler fraction of various resin composites. Mechanical properties of eighteen different resin composites were investigated in this study; flexural strength (FS), flexural modulus (FM), fracture toughness (FT...

journal_title：Dental materials journal

authors： Jun SK,Kim DA,Goo HJ,Lee HH

更新日期：2013-01-01 00:00:00

abstract：:This study examined the ability of a photocatalyst mixed in a denture base resin to decompose organic substances which adhered to the denture base resin surface. The photocatalyst was mixed with denture base resin at concentrations of 0, 5, 10, and 15% (w/w). Decomposition test, bending test, and surface roughness mea...

journal_title：Dental materials journal

authors： Cheng Y,Sakai T,Moroi R,Nakagawa M,Sakai H,Ogata T,Terada Y

更新日期：2008-03-01 00:00:00

abstract：:This study was to evaluate the load bearing capacity of monolithic dental zirconia crowns, and the effect of surface finishing on fracture strength. (1) The zirconia plates were divided into 5 groups and polished by various types of polishing bur, every specimen was analyzed by surface roughness testing, and X-ray dif...

journal_title：Dental materials journal

authors： Yin R,Lee MH,Bae TS,Song KY

更新日期：2019-03-31 00:00:00

abstract：:This study aimed to investigate the maximum depth imaging and optical properties of the dentin near the pulp by using optical coherence tomography (OCT) and to explore the possibility of measuring the remaining dentin thickness (RDT). Human third molars were used. In experiment 1, the cuspal dentin blocks (0.50-mm to ...

journal_title：Dental materials journal

authors： Fujita R,Komada W,Nozaki K,Miura H

更新日期：2014-01-01 00:00:00

abstract：:The purposes of this study were to examine the shock absorption capability of addition-cured silicone denture relining materials and the bonding strength of addition-cured silicone denture relining materials and a commercial mouthguard material to determine its applicability to mouthguard adjustment. Two addition-cure...

journal_title：Dental materials journal

authors： Fukasawa S,Churei H,Chowdhury RU,Shirako T,Shahrin S,Shrestha A,Wada T,Uo M,Takahashi H,Ueno T

更新日期：2016-01-01 00:00:00

abstract：:The behavior of microencapsulated polymerization initiators in dental adhesives is unknown. This study investigated the effects of new microencapsulated initiators in novel, multi-purpose, PMMA-type adhesive resin on the bonding performance and polymerization reactivity. Microencapsulated BPO and 1,3,5-trimethylbarbit...

journal_title：Dental materials journal

authors： Fuchigami K,Ikemura K,Ichizawa K

更新日期：2008-01-01 00:00:00

abstract：:The aim of this in vitro study was to evaluate the effects of different preparation angles on the precision of fit of zirconia crown frameworks. Dies were fabricated with three different preparation angles: 4, 8, and 12 degrees total taper. Ten copings were fabricated for each angle by a laboratory and a milling-cente...

journal_title：Dental materials journal

authors： Beuer F,Edelhoff D,Gernet W,Naumann M

更新日期：2008-11-01 00:00:00

abstract：:The effects of monomer structure on the mechanical properties of visible light-cured composite resins based on the seven types of aromatic dimethacrylates were investigated. The results of this study suggested that the mechanical properties of the composite resins were dependent upon the chemical structure of the dime...

journal_title：Dental materials journal

authors： Kawaguchi M,Fukushima T,Horibe T

更新日期：1989-06-01 00:00:00

abstract：:The purpose of this study was to evaluate the influence of heating, cast bonding, and subsequent polishing procedures on attractive force of magnetic attachments. Two magnetic attachment systems with keepers of different chemical compositions (Hicorexslim 3013, 447J1; Magfit EX400, AUM20) were employed. Keepers examin...

journal_title：Dental materials journal

authors： Ohashi N,Koizumi H,Ishikawa Y,Furuchi M,Matsumura H,Tanoue N

更新日期：2007-05-01 00:00:00

abstract：:This study investigated the changes in hardness and Young's modulus of the transparent layer of dentin associated with aging and the carious process. Eighteen extracted human molars with or without coronal caries were used in this study. The normal teeth were divided into two groups by age, and the carious teeth were ...

journal_title：Dental materials journal

authors： Zheng L,Nakajima M,Higashi T,Foxton RM,Tagami J

更新日期：2005-12-01 00:00:00

abstract：:This study examined the surface microhardness of four kinds of resin composites with different fillers and resin matrices. Ten specimens of 2 mm thickness and 4 mm diameter of each resin composite were polymerized using a halogen light, a blue light-emitted diode, and a plasma arc unit. Microhardness evaluation was pe...

journal_title：Dental materials journal

authors： Hubbezoğlu I,Bolayir G,Doğan OM,Doğan A,Ozer A,Bek B

更新日期：2007-11-01 00:00:00

abstract：:Quaternary ammonium compounds (QACs) have been used widely in medicine, owing to their antimicrobial properties. They also have strong permeability, stable performance, low skin irritation, low toxicity, low corrosion, lasting biological effects and so on, comparing with other antimicrobial agents. At the end of last ...

journal_title：Dental materials journal

authors： Zhang Y,Chen Y,Hu Y,Huang F,Xiao Y

更新日期：2018-03-30 00:00:00

abstract：:The objective of this study was to test the hypothesis that thermal cycling weakens the flexural strength of porcelain. Specimens of Deguceram Gold and Vita Omega 900 were tested in four groups of 30 specimens each: in the original glazed condition versus being ground with 1000-grit, 600-grit, and 100-grit silicon car...

journal_title：Dental materials journal

authors： Nakamura Y,Hojo S,Sato H

更新日期：2009-07-01 00:00:00

abstract：:The aim of this in vitro study was to evaluate the effects of desensitizer pre-treatment on in-office bleaching using an artificial discoloration tooth model. The stained specimens were divided into four groups (n=10); without application (Control group), Shield Force plus (SF group), UltraEz (UE group) and Teeth Mate...

journal_title：Dental materials journal

authors： Kyaw KY,Otsuki M,Hiraishi N,Segarra MS,Tagami J

更新日期：2019-10-02 00:00:00

abstract：:This study was evaluating how three desensitizing toothpastes used at home influence the effect associated with desensitizing agents after application in the clinic. Fifty dentine disks measure it permeability and 32 dentine disks with similar permeability levels were selected. Following Dental desensitizer treatment,...

journal_title：Dental materials journal

authors： Hu ML,Zheng G,Jiang RD,Han JM,Zhang YD,Lin H

更新日期：2020-09-29 00:00:00

abstract：:The objective of this study was to evaluate, using methylene blue (MB), the effects of various light sources on the bleaching action of hydrogen peroxide (H(2)O(2)) with two titanium dioxide (TiO(2)) photocatalysts - an ultraviolet light-activated TiO(2) photocatalyst (UVTiO(2)) versus a visible light-activated TiO(2)...

journal_title：Dental materials journal

authors： Suyama Y,Otsuki M,Ogisu S,Kishikawa R,Tagami J,Ikeda M,Kurata H,Cho T

更新日期：2009-11-01 00:00:00

abstract：:The physical properties of experimental visible light-activated resins containing dyestuff, which could be quickly discolored by irradiation was, evaluated by analyzing light absorbance characteristics and measuring micro Vickers hardness. The experimental resin, which was prepared by mixing equivalent weights of Bis ...

journal_title：Dental materials journal

authors： Nakazato J,Itoh K,Wakumoto S

更新日期：1989-12-01 00:00:00

abstract：:This study aimed to introduce a procedure for determining the bilinear elastic moduli (E1 and E2) of the periodontal ligament for a mathematical tooth model to analyse stress in the mandible. The bone and tooth morphology were scanned from a dry skull and an extracted intact tooth, respectively, and reconstructed in a...

journal_title：Dental materials journal

authors： Borák L,Florian Z,Bartáková S,Prachár P,Murakami N,Ona M,Igarashi Y,Wakabayashi N

更新日期：2011-01-01 00:00:00

abstract：:This study aimed to evaluate the inhibitory effect of experimental pastes containing surface pre-reacted glass ionomer (S-PRG) fillers on enamel demineralization. Bovine blocks were treated twice a day for 4 days by 7 groups; experimental pastes containing 0-30 wt% S-PRG filler (S00, S01, S05, S10, and S30), deionized...

journal_title：Dental materials journal

authors： Nakamura K,Hamba H,Nakashima S,Sadr A,Nikaido T,Oikawa M,Uo M,Tagami J

更新日期：2017-07-26 00:00:00

abstract：:This study investigated the contrast ratio and grain size depending on sintering parameters of twelve different zirconia materials and compared with glass-ceramic (N=156, n=12 per group). Contrast ratio of all ceramics was measured using a spectrophotometer according to ISO 2471: 2008. Grain sizes of zirconia were det...

journal_title：Dental materials journal

authors： Stawarczyk B,Emslander A,Roos M,Sener B,Noack F,Keul C

更新日期：2014-01-01 00:00:00

abstract：:This research was conducted to investigate the bond strength between artificial teeth and a thermoplastic denture base resin for injection molding with different surface preparations for use in flexible resin removable partial dentures. Composite resin denture teeth and acrylic denture resin teeth were bonded to three...

journal_title：Dental materials journal

authors： Tashiro S,Kawaguchi T,Hamanaka I,Takahashi Y

更新日期：2021-01-15 00:00:00

abstract：:The aim of the study was to evaluate bone regeneration using a canine model with surgically created periodontal defects filled for 12 weeks using a stratified biomaterial consisting in a biphasic calcium phosphate (BCP) covered with a crosslinking hydrogel acting as polymer membrane of silated hydroxypropyl methylcell...

journal_title：Dental materials journal

authors： Struillou X,Fruchet A,Rakic M,Badran Z,Rethore G,Sourice S,Fellah BH,LE Guehennec L,Gauthier O,Weiss P,Soueidan A

更新日期：2018-09-30 00:00:00

abstract：:The aim of this study was to evaluate the effect of resin infiltration on root caries induced by Streptococcus mutans biofilms. Human premolar specimens were divided to 5 groups: negative control (NC), Clearfil SE Bond (SEB), Icon-etch120s+Icon-infiltrant (HA120), Icon-etch10s+Icon-infiltrant (HA10) and K-etchant10s+I...

journal_title：Dental materials journal

authors： Zhou Y,Matin K,Shimada Y,Sumi Y,Tagami J

更新日期：2017-03-31 00:00:00

abstract：:This study evaluated the effect of adding silane coupling agent on initial and long-term bond strengths of one-step self-etch adhesives to enamel-dentin-composite in combined situation. Cervical cavities were prepared on extracted molars and filled with Clearfil AP-X. After water-storage for one-week, the filled teeth...

journal_title：Dental materials journal

authors： Mamanee T,Takahashi M,Nakajima M,Foxton RM,Tagami J

更新日期：2015-01-01 00:00:00

abstract：:This study evaluated the influence of an aqueous propolis-based solution (PROP) on gap formation and bond strength of posts bonded to root canal dentin using resin cements. Endodontically-treated bovine incisors received different irrigation protocols: 1) 2.5% sodium hypochlorite (NaOCl)/17% EDTA/NaOCl; 2) saline solu...

journal_title：Dental materials journal

authors： Matochek MHM,Tomaz PLS,Oliveira TS,Polassi MR,Alonso RCB,Scremin FM,Sauro S,Marcucci MC,D'Alpino PHP

更新日期：2020-06-05 00:00:00

abstract：:This study investigated the effects of storing impressions for 3 hours after spraying them with a disinfectant solution on dimensional change and deformation of maxillary edentulous stone models. Three brands of alginate impression materials, characterized by a small degree of contraction in 100% relative humidity, we...

journal_title：Dental materials journal

authors： Hiraguchi H,Kaketani M,Hirose H,Yoneyama T

更新日期：2010-05-01 00:00:00

abstract：:This study evaluated the influence of heat treatment (HT) of the silane on the microtensile bond strength of resin cement to a feldspathic ceramic. Ceramic (VITA VM7) and composite blocks (N=32) were divided into four groups (n=6 for bond test, n=2 for SEM) at random and subject to following sequence of conditioning: ...

journal_title：Dental materials journal

authors： de Carvalho RF,Martins ME,de Queiroz JR,Leite FP,Ozcan M

更新日期：2011-01-01 00:00:00