Abstract:
:This study compared the post-gel contraction of two "low-shrinkage" composites (InTen-S [IS], Ivoclar-Vivadent; Aelite LS [AL], BISCO Inc) and an ormocer (Admira [AM], Voco) to two conventional mini-filled composites (Renew [RN], BISCO; Z100 [ZO], 3M ESPE). A strain-monitoring device and test configuration were used to measure the linear polymerization shrinkage associated with the various composites (A2 shade) during and up to 60 minutes post light polymerization. Each specimen was irradiated for 40 seconds using a halogen curing light (Max, Dentsply-Caulk) with an intensity of 401 mW/cm2. Five specimens were made for each composite. Data was analyzed using one-way ANOVA/Scheffe's post-hoc test at significance level 0.05. The linear percentage shrinkage immediately after light polymerization and at 60 minutes post light polymerization ranged from 0.10 +/- 0.02 to 0.40 +/- 0.02% and 0.22 +/- 0.02 to 0.60 +/- 0.05%, respectively. Post-gel shrinkage ranking of the materials was as follows: immediately after light polymerization - IS < AL < AM < ZO < RN and at 60 minutes post light polymerization - IS < AL = AM < ZO < RN. The shrinkage associated with IS, AL and AM was significantly lower than for ZO and RN immediately after light polymerization and at 1, 10, 30 and 60 minutes post light polymerization. The post-gel polymerization shrinkage of IS, AL and AM was significantly lower than conventional mini-filled composites.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Yap AU,Soh MSkeywords:
subject
Has Abstractpub_date
2004-03-01 00:00:00pages
182-7issue
2eissn
0361-7734issn
1559-2863journal_volume
29pub_type
杂志文章abstract::Veneers were fabricated by CEREC CAD-CAM and the platinum foil techniques for standardized preparations on 10 artificial teeth. Mesial preparation contacts were broken, but distal contacts remained intact. The veneers were cemented in a standardized manner to their teeth. The veneers and their attached cement were emb...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1997-05-01 00:00:00
abstract::The nature of the hybrid layer (HL) following chemical treatment has not been resolved. The effects of chemical treatments and polishing on HL morphology and composition were investigated using micro-Raman spectroscopy and SEM. Polished and unpolished SingleBond adhesive/dentin (a/d) interfaces from the same tooth wer...
journal_title:Operative dentistry
pub_type: 临床试验,杂志文章,随机对照试验
doi:
更新日期:2004-11-01 00:00:00
abstract::Most manufacturers of dental adhesives have both a total-etch adhesive and a simplified self-etching adhesive available on the market. This study measured the enamel microtensile bond strengths of five pairs of enamel adhesives as a function of enamel roughness. The proximal surfaces of 25 extracted mandibular molars ...
journal_title:Operative dentistry
pub_type: 临床试验,杂志文章,随机对照试验
doi:
更新日期:2005-07-01 00:00:00
abstract::The present in vitro study concerns determination of the pre-cementation gap width of all-ceramic crowns made using an in-office digital-impression technique and subsequent computer-aided design/computer-aided manufacturing (CAD/CAM) production. Two chairside video camera systems were used: the Lava Oral scanner and C...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/12-309-L
更新日期:2014-05-01 00:00:00
abstract::The authors describe a minimally invasive procedure for occlusal rehabilitation in a young patient presenting with mild mandibular prognathism and loss of occlusal vertical dimension caused by dental erosion from chronic gastroesophageal reflux. ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/09-110T
更新日期:2010-01-01 00:00:00
abstract::This study investigated the influence of curing lights and modes on the cross-link density of dental composites. Four LED/halogen curing lights (LED-Elipar Freelight [FL], 3M-ESPE and GC e-light [EL], GC; high intensity halogen-Elipar Trilight [TL], 3M-ESPE; very high intensity halogen-Astralis 10 [AS], Ivoclar Vivade...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2004-07-01 00:00:00
abstract:PURPOSE:This study evaluated the amount of residual yellow in cured resin composites when polymerizing with either a quartz-tungsten-halogen (QTH) or blue light-emitting diode (LED). MATERIAL AND METHODS:Twelve shades (bleaching to conventional shades) of microfill, hybrid and microhybrid resin composite specimens (n ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/06-129
更新日期:2007-09-01 00:00:00
abstract::This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone fo...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-064-L
更新日期:2016-07-01 00:00:00
abstract::Retained primary teeth in the smile zone can cause patient dissatisfaction, especially if associated with malposition of teeth. Orthodontic and prosthetic treatment options to treat the situation may not be accepted by some patients. Therefore, these patients tend to maintain their primary teeth and seek different est...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-363-S
更新日期:2017-03-01 00:00:00
abstract::The aim of this study was to determine whether using a silane-containing universal adhesive as a silane primer in glass-ceramic/resin cement systems affects biaxial flexural strength (BFS) and bonded interface integrity after loading. Glass-ceramic (IPS e.max CAD, Ivoclar/Vivadent, Schaan, Liechtenstein) disc-shaped s...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/17-356-L
更新日期:2019-03-01 00:00:00
abstract:OBJECTIVE:To study the interfacial ultra-morphology formed by "all-in-one" self-etch adhesives. METHODS:Forty-nine extracted molars were assigned to one of five all-in-one adhesives: Adper Prompt L-Pop (AP, 3M ESPE); Clearfil S3 Bond (S3, Kuraray); G-Bond (GB, GC America); iBond (iB, Heraeus Kulzer) and Xeno IV (XE, D...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/07-133
更新日期:2008-09-01 00:00:00
abstract::This in vitro study investigated the effects of a thin layer of flowable composite or compomer on microleakage occurring in Class II packable and nanofilled composite restorations that extend apical to the cemento-enamel junction (CEJ). The current study also investigated any differences in microleakage that occur bet...
journal_title:Operative dentistry
pub_type: 杂志文章,随机对照试验
doi:10.2341/08-91
更新日期:2009-05-01 00:00:00
abstract:CLINICAL RELEVANCE:Using a material that optimizes marginal seal when using a margin elevation technique to manage deep class II cavities should enhance clinical outcomes. SUMMARY:Objectives: The purpose of this laboratory study was to perform a tridimensional interfacial gap evaluation of class II cavities with ename...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/19-161-L
更新日期:2020-09-01 00:00:00
abstract::Treatment of a caries active patient requires the clinician to be knowledgeable in the restorative and risk management issues with which these patients often present. Modifications of risk factors that promote dental caries play an important part in the long-term restorative success in these patients. Patient complian...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2002-03-01 00:00:00
abstract::A core foundation system is frequently used in endodontically treated teeth that suffer excessive loss of the coronal portion of their structure. The volumetric shrinkage of core foundation resins may create marginal gaps that influence the bonding ability and longevity of a restored tooth. Little is known about how a...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2005-09-01 00:00:00
abstract::The present clinical case report describes the clinical steps of enamel microabrasion associated with dental bleaching to restore severely-pitted fluorosed teeth. The process of removing the fluorotic superficial stains started by using macroabrasion with a water-cooled fine tapered 3195 FF diamond bur. Rubber dam iso...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/18-116-T
更新日期:2019-11-01 00:00:00
abstract::The reasons for placement and replacement and the longevity of amalgam restorations were recorded by 62 Italian private practitioners. The survey compiled 1935 amalgam restorations inserted due to primary caries (59%) and failed restorations (41%). The clinical diagnosis of secondary caries constituted 59% of failures...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1992-03-01 00:00:00
abstract::This study evaluated the effects of two in-office bleaching agents (Beyond and Opalescence Boost) with different pH on the structure and mechanical properties of human enamel in vitro and in situ. One hundred and eight enamel slabs were obtained from freshly extracted premolars. The specimens were randomly distributed...
journal_title:Operative dentistry
pub_type: 杂志文章,随机对照试验
doi:10.2341/11-173-L
更新日期:2013-01-01 00:00:00
abstract::Coronal fractures of posterior teeth are not rare in clinical practice. Most of the time they constitute a restorational problem for the clinician, since they usually end below the free gingival crest. Two hundred coronal fractures of posterior teeth were examined in this study, with respect to several factors. Some o...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1989-01-01 00:00:00
abstract::In this laboratory study, the microtensile bond strengths (μTBS) of resin-modified glass ionomer cement (RM-GIC) to sound and artificial caries-affected bovine root dentin (ACAD) using three different conditioning agents were evaluated after 24 hours and three months. The fractured interface was examined with a scanni...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/16-375-L
更新日期:2017-11-01 00:00:00
abstract:OBJECTIVE::Computer aided design-computer aided machining (CAD-CAM) ceramic crowns are replacing ceramo-metal ones due to newly developed mechanical properties and esthetics. To obtain knowledge about their interactions due to polishing and occlusal contacts with the opposing dental enamel specimen, including surface r...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/17-153-L
更新日期:2019-01-01 00:00:00
abstract::The purpose of this study was to determine if air thinning three dentin adhesives would affect bond strength to dentin. Ninety human molars were mounted in acrylic and the occlusal surfaces ground to expose a flat dentin surface. Thirty teeth were randomly assigned to one of the following dentin bonding agent/composit...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1995-07-01 00:00:00
abstract:OBJECTIVE:This study evaluated the differences in enamel color change, surface hardness, elastic modulus, and surface roughness between treatments with four bleaching gels containing carbamide peroxide (two at 10% and one each at 35%, and 45%) and two bleaching gels containing hydrogen peroxide (two at 40%). METHODS:E...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-010-L
更新日期:2016-01-01 00:00:00
abstract::This article reports the case of a patient with bilateral hypodontia of the maxillary lateral incisors who was dissatisfied with the outcome of initial orthodontic treatment, highlighting the importance of a multidisciplinary interaction among Restorative Dentistry, Orthodontics, and Implantology to achieve satisfacto...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/11-167-T
更新日期:2012-09-01 00:00:00
abstract::This study investigated the influence of light energy density (intensity x time) on the effectiveness of composite cure in view of the curing profiles of new light-polymerization units. This investigation used a digital microhardness tester to evaluate the hardness of the top/bottom surfaces and hardness ratio of 2 mm...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2001-09-01 00:00:00
abstract:AIMS:To evaluate the effect of two composite restorative techniques (direct bulk fill vs indirect CAD/CAM) on the fracture resistance and mode of fracture of extended mesio-occlusal-distal (MOD) cavity preparations. METHODS:Fifty-one sound human mandibular third molars were divided into three groups (n=17). Extended b...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/18-013-L
更新日期:2019-05-01 00:00:00
abstract::This study evaluated the effect of two dentin disinfectants (Consepsis, Tubulicid), one aqueous HEMA solution (Aqua Prep), a combination of Aqua Prep and Tubulicid and an air abrasion treatment (50 microns aluminum oxide) on the shear bond strength (SBS) of two acetone-based single bottle adhesives (One Step and Prime...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2001-11-01 00:00:00
abstract:INTRODUCTION:Limited access to interdental spaces complicates removal of excess material when placing class II composite resin restorations. Evidence-based recommendations on interproximal finishing are rare. We present novel microscalpels for this indication. The aim of the study was to test their fracture strength an...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/16-012-L
更新日期:2017-05-01 00:00:00
abstract::The aims of this study were to investigate 1) the influence of cleansing methods after saliva contamination and 2) aging conditions (thermocycling and water storage) on zirconia shear bond strength (SBS) with a resin cement. One hundred and eighty zirconia specimens were sandblasted with 50 μm aluminum oxide particles...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/13-323-L
更新日期:2015-03-01 00:00:00
abstract::Amalgapins are susceptible to early fracture during matrix removal and carving. The purpose of this study was to examine the early fracture resistance of amalgapin-retained restorations using a spherical amalgam alloy, an admixed amalgam alloy, a combination of admixed alloy over the spherical alloy, and a recently in...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1998-03-01 00:00:00