Abstract:
:Amalgapins are susceptible to early fracture during matrix removal and carving. The purpose of this study was to examine the early fracture resistance of amalgapin-retained restorations using a spherical amalgam alloy, an admixed amalgam alloy, a combination of admixed alloy over the spherical alloy, and a recently introduced modified spherical amalgam alloy. Four amalgapin channels with a diameter of 1.4 mm and depth of 2 mm were prepared in cylinders of Macor, a machinable ceramic material. The amalgapins were hand condensed, and the bulk of the restoration was mechanically condensed. In the group using the combination of alloys, 800 mg of spherical alloy was condensed into the amalgapins and over the floor of the preparation. The admixed alloy was then condensed over the spherical alloy to build up the bulk of the restoration. Using an Instron Universal Testing Machine, the restorations were tested to shear failure at an average of 15.8 +/- 1.3 minutes after the initiation of trituration of the amalgam alloy. A metal ring was placed around the restoration and pulled 90 degrees to the long axis to simulate matrix band removal. Data were analyzed using Kruskal-Wallis procedures. The fracture resistance of the spherical alloy group and the spherical/admixed group were significantly higher than admixed or Tytin FC. All fractures occurred in amalgam at the entrance to the amalgapin channel. The combination of spherical and admixed amalgam alloys in a restoration may reduce the potential for early dislodgment while allowing additional time for carving.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Schulte GA,Hermesch CB,Vandewalle KS,Buikema DJsubject
Has Abstractpub_date
1998-03-01 00:00:00pages
108-12issue
3eissn
0361-7734issn
1559-2863journal_volume
23pub_type
杂志文章abstract:OBJECTIVES:To evaluate the effect of application protocol in resin-enamel microshear bond strength (μSBS), in situ degree of conversion, and etching pattern of three universal adhesive systems. METHODS AND MATERIALS:Sixty-three extracted third molars were sectioned in four parts (buccal, lingual, and proximals) and di...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-213-L
更新日期:2016-09-01 00:00:00
abstract::Minimally invasive flowable composite Class I restorations are widely used. However, flowable composites are characterized by low filler contents, modified resin formulations, low moduli of elasticity, low viscosity, generally poor mechanical properties, and decreased long-term stability. The purpose of this study was...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/11-106-L
更新日期:2012-05-01 00:00:00
abstract::This in vitro study investigated the possible dehydration of dentin caused by bleaching agents. Furthermore, it tested whether protective dentin varnishes can maintain the physiological moisture of dentin during bleaching treatment. Fifty-five standardized dentin cylinders were prepared from freshly extracted bovine i...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/05-89
更新日期:2006-09-01 00:00:00
abstract::Detailed and accurate impressions are made when the oral environment is dry during the impression process. Maintaining a dry field on medically, physically, or emotionally compromised patients can be very challenging. If not achieved, it may compromise dental care and accurate outcomes. This article describes a techni...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/11-290-T
更新日期:2014-01-01 00:00:00
abstract:OBJECTIVES:To evaluate the effect of different surface treatments on the bond strength to a composite and a polymer-infiltrated ceramic CAD/CAM block after six-month artificial aging. METHODS AND MATERIALS:Two types of CAD/CAM blocks (Cerasmart, GC; Enamic, Vita Zahnfabrik) were cut in slabs of 4-mm thickness, divided...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-263-L
更新日期:2017-01-01 00:00:00
abstract::A core foundation system is frequently used in endodontically treated teeth that suffer excessive loss of the coronal portion of their structure. The volumetric shrinkage of core foundation resins may create marginal gaps that influence the bonding ability and longevity of a restored tooth. Little is known about how a...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2005-09-01 00:00:00
abstract::Various core materials with different shades affect the final color of high-translucency monolithic zirconia restorations. The blue core shows the greatest color difference in final zirconia restorations followed by metal, A3 dentin-shade resin core, and white core. ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/19-238-L
更新日期:2020-12-21 00:00:00
abstract:PURPOSE:This study evaluated the effect of thermocycling on the microtensile bond strength of four adhesive luting agents to GN-I CAD-CAM ceramic. The hypothesis tested was that thermocycling did not affect bonding effectiveness, irrespective of the luting agents used. MATERIALS AND METHODS:Ceramic specimens of two di...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/06-106
更新日期:2007-07-01 00:00:00
abstract:OBJECTIVE:The purpose of this study was to evaluate surface finish and gloss of a two-step composite finishing/polishing (F/P) disc system compared with two multistep systems on five composites. METHODS:Seventy-five disc-shaped composite specimens (D=10.0 mm, 2 mm thick, n=15 per composite) were made of microfill (Dur...
journal_title:Operative dentistry
pub_type: 杂志文章,随机对照试验
doi:10.2341/10-162-L
更新日期:2011-03-01 00:00:00
abstract::This research investigated the effects of wet and dry conditions of phosphoric acid etched dentin on resin bonding and determined the optimum moisture condition for resin bonding using an ethanol-based one-bottle adhesive system. Bovine dentin surfaces were etched with 35% phosphoric acid and rinsed with water. Under ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:2002-11-01 00:00:00
abstract::The present in vitro study concerns determination of the pre-cementation gap width of all-ceramic crowns made using an in-office digital-impression technique and subsequent computer-aided design/computer-aided manufacturing (CAD/CAM) production. Two chairside video camera systems were used: the Lava Oral scanner and C...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/12-309-L
更新日期:2014-05-01 00:00:00
abstract::Post-operative sensitivity (POS) may be observed in recently placed posterior composites. Evidence-based guidelines for the management of posterior composites with POS have yet to be determined. This study examined a retrospective analysis of the findings of a unique multi-center clinical trial to investigate the five...
journal_title:Operative dentistry
pub_type: 临床试验,杂志文章,多中心研究
doi:
更新日期:2003-11-01 00:00:00
abstract::In some patients with labial white stains involving the enamel and dentin, bleaching associated with a restorative procedure using composites may be an appropriate treatment alternative. Although bleaching makes the teeth and the stain whiter, the staining is less evident and easier to restore. Restorative procedures ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/12-284-T
更新日期:2013-07-01 00:00:00
abstract::This study investigated the effect of conventional and acidified casein phosphopeptide-amorphous calcium phosphate-containing crèmes (CPP-ACP and ACPP-ACP) on dentin permeability (DP) before and after acid challenge, using a fluid-flow measuring device and scanning electron microscopic (SEM) examination. Fifty dentin ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/17-382-L
更新日期:2019-09-01 00:00:00
abstract::The current study investigated the influence of carbamide peroxide on the flexural strength of tooth-colored restorative materials at two environmental temperatures. Seven restorative materials were used, including four resin composites (Filtek Z350, Filtek Z250, Synergy Flow and Filtek P60), a polyacid-modified compo...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/09-139-L
更新日期:2010-05-01 00:00:00
abstract::This study evaluated the pulp biocompatability of a new light-cured composite resin which was placed in etched glass-ionomer-lined cavities of monkey teeth. The pulpal response to this material was less than that to zinc-oxide eugenol cement in each observation period. Therefore this material seems to meet acceptable ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1991-07-01 00:00:00
abstract::While a one-year report had been previously published, this study was undertaken to evaluate the clinical performance and appearance of a resin-modified glass ionomer and a resin composite over two years. Thirty-seven pairs of restorations of FujI II LC and Z 250/Single Bond were placed in caries-free cervical erosion...
journal_title:Operative dentistry
pub_type: 临床试验,杂志文章,随机对照试验
doi:
更新日期:2003-09-01 00:00:00
abstract:OBJECTIVES:The aim of this study was to quantify the internal void volume formation in commercially available, resin composites inserted using conventional or sonic insertion methods, and analyzed using three-dimensional (3D) micro-computed tomography (μCT). METHODS AND MATERIALS:Four resin composites were evaluated: ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/16-331-L
更新日期:2018-03-01 00:00:00
abstract::The effect of interdental separation of a special separation ring and wooden wedge was investigated. In a split-mouth design, 27 patients were randomly assigned to one of two groups (W or S). In 11 patients, an interdental wooden wedge (Hawe-Neos) was placed (group W), and in 16 patients, a separation ring (Composi-Ti...
journal_title:Operative dentistry
pub_type: 杂志文章,随机对照试验
doi:10.2341/06-73
更新日期:2007-05-01 00:00:00
abstract::For many years, operative dentistry has been using regenerative approaches to treat dental disease. The use of calcium hydroxide to stimulate reparative or reactionary dentin is clearly an example of such a therapeutic strategy. The advent of tissue engineering is allowing dentistry to move forward in the use of regen...
journal_title:Operative dentistry
pub_type: 杂志文章,评审
doi:10.2341/06-000
更新日期:2006-11-01 00:00:00
abstract::This investigation evaluated the stabilizing effect of glass fiber reinforced posts (FRP) luted with self-adhesive universal cement on the fracture resistance of excessively flared endodontically treated teeth (ETT). Values were compared to teeth with no ferrule, 2 mm ferrule and resin cement for luting with 2 mm ferr...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/05-142
更新日期:2006-11-01 00:00:00
abstract::This study determined the influence of light curing protocols and matrix type on the margin quality and marginal seal of Class II resin-based composite restorations. In extracted human molars, box-shaped MOD cavities with 1 mm wide interproximal bevels were prepared with cervical margins located at least 1 mm coronal ...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/04-194
更新日期:2006-01-01 00:00:00
abstract::This investigation examined the susceptibility to staining and translucency changes of some new tooth-colored restorative materials after immersion in different beverages. The materials studied were 3M Filtek Z350XT (ZT), 3M Filtek 350XT Flowable Restorative (ZF), Shofu Beautifil Flow Plus (BF), Shofu Beautifil II (B2...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/149027-L
更新日期:2015-03-01 00:00:00
abstract:PURPOSE:To investigate the effect of different light exposure times, shades, and thicknesses on the depth of cure (DOC) of bulk fill composites. METHODS AND MATERIALS:Two bulk fill composites, Tetric EvoCeram Bulk Fill (TBF) and Sonic Fill (SF), and a conventional composite, Filtek Supreme Ultra (FSU), were evaluated....
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/16-057-L
更新日期:2017-09-01 00:00:00
abstract:OBJECTIVES::The use of high-viscosity glass-ionomer cements (HVGICs) for atraumatic restorative treatment (ART) restorations is widely practiced with the advent of various HVGICs. However, the bonding of the latter to caries-affected dentin (CAD) should be validated, especially because it is the common substrate left a...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/17-154-L
更新日期:2018-11-01 00:00:00
abstract::This in vitro study evaluated the amount of fluoride released from fluoride-containing materials over a period of 28 days. Six disk samples (2.06 +/- 0.06 cm2) were prepared of each material and divided at random into seven groups: Group 1: Chelon-Fil; Group 2: Chelon-Silver; Group 3: VariGlass; Group 4: Dyract; Group...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1996-09-01 00:00:00
abstract::This study evaluated (1) the effect of known reductions in the output of curing lights on the depth of cure of various resins as determined by hardness measurements, and (2) the ability of the clinician to detect reduced light output by use of an explorer to compare the hardness of the top and bottom surfaces of resin...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1994-03-01 00:00:00
abstract::Retained primary teeth in the smile zone can cause patient dissatisfaction, especially if associated with malposition of teeth. Orthodontic and prosthetic treatment options to treat the situation may not be accepted by some patients. Therefore, these patients tend to maintain their primary teeth and seek different est...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:10.2341/15-363-S
更新日期:2017-03-01 00:00:00
abstract::The available and proposed methods for determining the in vivo occlusal wear values of classes 1 and 2 restorations made of resinfilled composite materials are critically reviewed. A methodology to be used to address the fundamental question of the link between the wear of the in vivo restorations and the relevant mec...
journal_title:Operative dentistry
pub_type: 杂志文章,评审
doi:
更新日期:1991-03-01 00:00:00
abstract::Excessive etching of the dentin may decrease bond strength because the adhesive may fail to completely infiltrate to the base of the over-etched demineralized collagen network. The purpose of the present study was to evaluate the influence of increasing etching times on the microtensile bond strength of Single Bond an...
journal_title:Operative dentistry
pub_type: 杂志文章
doi:
更新日期:1999-05-01 00:00:00