The effect of light curing source on the residual yellowing of resin composites.

Abstract:

PURPOSE:This study evaluated the amount of residual yellow in cured resin composites when polymerizing with either a quartz-tungsten-halogen (QTH) or blue light-emitting diode (LED). MATERIAL AND METHODS:Twelve shades (bleaching to conventional shades) of microfill, hybrid and microhybrid resin composite specimens (n = 10) were polymerized with both light types. All the materials contained only camphorquinone as the photoinitiator. After exposure, the specimens were stored in the dark for 24 hours. Then, the specimen color parameters were recorded (L*, a*, b* and C*(ab)) and color differences (deltaE*(ab)) were determined by examining for changes among the test combinations. Group comparisons were examined using ANOVA and the Tukey-Kramer post-hoc test, and pairwise comparisons were made using the Student's t-tests at a pre-set alpha of 0.05. RESULTS:When a significant difference in the shade of yellow was noted, the QTH light produced a greater yellow tinge than most comparisons using the LED. The potential for producing more residual yellowing could not be anticipated with respect to composite filler classification or shade, as this effect may be more dependent on individual product composition. The extent to which residual yellowing differences were noted between light curing units fell within levels considered detectable by the human eye (deltaE > 2.0). CONCLUSION:The selection of light curing unit to polymerize resin-based restorative materials can have a significant influence on the amount of residual yellow present, with the QTH light tending to leave more yellow than an LED unit.

journal_name

Oper Dent

journal_title

Operative dentistry

authors

Brackett MG,Brackett WW,Browning WD,Rueggeberg FA

doi

10.2341/06-129

subject

Has Abstract

pub_date

2007-09-01 00:00:00

pages

443-50

issue

5

eissn

0361-7734

issn

1559-2863

journal_volume

32

pub_type

杂志文章
  • Analysis of the degree of conversion of LED and halogen lights using micro-Raman spectroscopy.

    abstract::This study determined the degree of conversion of two LED (light-emitting diodes) (Elipar FreeLight [FL], 3M ESPE; GC e-Light [EL], GC), a high intensity (Elipar TriLight [TL], 3M ESPE) and a very high intensity (Astralis 10 [AS], Ivoclar Vivadent) halogen light. The degree of conversion of these lights was compared t...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Soh MS,Yap AU,Yu T,Shen ZX

    更新日期:2004-09-01 00:00:00

  • Pulpal response to a new light-cured composite placed in etched glass-ionomer lined cavities.

    abstract::This study evaluated the pulp biocompatability of a new light-cured composite resin which was placed in etched glass-ionomer-lined cavities of monkey teeth. The pulpal response to this material was less than that to zinc-oxide eugenol cement in each observation period. Therefore this material seems to meet acceptable ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Hosoda H,Inokoshi S,Shimada Y,Harnirattisai C,Otsuki M

    更新日期:1991-07-01 00:00:00

  • Lesion Activity Assessment (LAA) in Conjunction With International Caries Detection and Assessment System (ICDAS) for Occlusal Caries Diagnosis in Permanent Teeth.

    abstract:OBJECTIVE:The aim of this study was to investigate the clinical performance and to validate the Lesion Activity Assessment (LAA) in conjunction with the International Caries Detection and Assessment System (ICDAS) for occlusal caries diagnosis in permanent teeth. METHODS:Patients with erupted or partially erupted thir...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/13-332-C

    authors: Cotta F,de Castilho LS,Moreira AN,Paiva SM,Ferreira EF,Ferreira LC,Magalhães CS

    更新日期:2015-09-01 00:00:00

  • Factors associated with microleakage in Class II resin composite restorations.

    abstract::This in vitro study investigated the correlation between factors related to cavosurface marginal adaptation and microleakage in Class II cavities restored with a light- or chemical-activated resin composite. Standardized cavities were prepared in 40 molars that were randomly divided between both materials. Each of the...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/06-16

    authors: Idriss S,Abduljabbar T,Habib C,Omar R

    更新日期:2007-01-01 00:00:00

  • Fluoride release from fluoride-containing materials.

    abstract::This in vitro study evaluated the amount of fluoride released from fluoride-containing materials over a period of 28 days. Six disk samples (2.06 +/- 0.06 cm2) were prepared of each material and divided at random into seven groups: Group 1: Chelon-Fil; Group 2: Chelon-Silver; Group 3: VariGlass; Group 4: Dyract; Group...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: de Araujo FB,García-Godoy F,Cury JA,Conceição EN

    更新日期:1996-09-01 00:00:00

  • Microleakage resistance of minimally invasive Class I flowable composite restorations.

    abstract::Minimally invasive flowable composite Class I restorations are widely used. However, flowable composites are characterized by low filler contents, modified resin formulations, low moduli of elasticity, low viscosity, generally poor mechanical properties, and decreased long-term stability. The purpose of this study was...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/11-106-L

    authors: Bonilla ED,Stevenson RG,Caputo AA,White SN

    更新日期:2012-05-01 00:00:00

  • The microtensile bond strength of Fuji IX glass ionomer cement to antibacterial conditioned dentin.

    abstract:INTRODUCTION:Adding antibacterial agents to a dentin conditioner used for a glass ionomer cement (GIC) has been shown to be antibacterial; however, it is not known whether this antimicrobial conditioning agent affects the bond strength to dentin in situ. This study applied GIC to antibacterial conditioned dentin withou...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Botelho MG

    更新日期:2005-05-01 00:00:00

  • Online Only Articles.

    abstract::On occasion we receive manuscripts that we would like to publish, but do not have the page room to include in the print journal. For the full article, please go to www.jopdentonline.org or enter the provided address into your address bar. ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/1559-2863-43.3.335

    authors:

    更新日期:2018-05-01 00:00:00

  • Rx for caries prevention: time line for home care. A software aid for communication of patient instructions for management of dental caries.

    abstract::Treatment of a caries active patient requires the clinician to be knowledgeable in the restorative and risk management issues with which these patients often present. Modifications of risk factors that promote dental caries play an important part in the long-term restorative success in these patients. Patient complian...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Newitter DA,Meiers JC,Kazemi RB

    更新日期:2002-03-01 00:00:00

  • Effect of bleaching on fracture toughness of resin composites.

    abstract::This study determined the effect of bleaching agents on the fracture toughness of composite materials. Four nanofilled resin composites were evaluated: Filtek Supreme Plus, Tetric EvoCeram, Premise and Esthet-X. Four concentrations of bleaching agents were tested: Opalescence PF 10%, 20%, 35% and 45%. Fifty specimens ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/08-120-L

    authors: Cho SD,Bulpakdi P,Matis BA,Platt JA

    更新日期:2009-11-01 00:00:00

  • Influence of adhesive application duration on dentin bond strength of single-application bonding systems.

    abstract::This study examined the relationship between the bond agent application duration and the dentin bond strength of several single-application bonding systems. The restorative material/ bonding systems used were Reactmer, with its single-application bonding system Reactmer Bond (RB, Shofu Inc, Kyoto, Japan); Palfique Est...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Miyazaki M,Tsubota K,Onose H,Hinoura K

    更新日期:2002-05-01 00:00:00

  • A simplified clinical technique for a routine indirect restoration impression on a challenging patient using a dry field illuminator.

    abstract::Detailed and accurate impressions are made when the oral environment is dry during the impression process. Maintaining a dry field on medically, physically, or emotionally compromised patients can be very challenging. If not achieved, it may compromise dental care and accurate outcomes. This article describes a techni...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/11-290-T

    authors: Santucci NM,Santucci ET,Geissberger M

    更新日期:2014-01-01 00:00:00

  • Effect of cyclic loading on the microtensile bond strengths of total-etch and self-etch adhesives.

    abstract:OBJECTIVE:To evaluate the effect of mechanical loading on the microtensile bond strength (MTBS) of five adhesive systems to dentin. METHODS:Flat dentin surfaces from human molars were divided into five groups and bonded with total-etch self-priming adhesives (Single Bond, Prime&Bond NT and Prime&Bond XP), two-step sel...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/04-161

    authors: Toledano M,Osorio R,Albaladejo A,Aguilera FS,Tay FR,Ferrari M

    更新日期:2006-01-01 00:00:00

  • Chromatic influence of value resin composites.

    abstract::The current study evaluated the chromatic influence of high, medium and low value composites on a dentin composite substrate (A2 shade) using spectrophotometric analysis. The specimens were divided into the following four groups: a) control (CG), entirely composed of dentin composite (n = 5); b) high value (GHV), dent...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/09-44-L

    authors: Schmeling M,Meyer-Filho A,de Andrada MA,Baratieri LN

    更新日期:2010-01-01 00:00:00

  • Effect of residual water on dentin bond strength and hybridization of a one-bottle adhesive system.

    abstract::This research investigated the effects of wet and dry conditions of phosphoric acid etched dentin on resin bonding and determined the optimum moisture condition for resin bonding using an ethanol-based one-bottle adhesive system. Bovine dentin surfaces were etched with 35% phosphoric acid and rinsed with water. Under ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Nakaoki Y,Nikaido T,Burrow MF,Tagami J

    更新日期:2002-11-01 00:00:00

  • Endodontic Access Effect on Full Contour Zirconia and Lithium Disilicate Failure Resistance.

    abstract:OBJECTIVES:To evaluate the effect of endodontic access on the failure load resistance of both adhesively and conventionally luted, full-contour monolithic yttria-stabilized zirconium dioxide (Y-TZP) and adhesively luted lithium disilicate (LD) crowns cemented on prepared teeth. METHODS AND MATERIALS:Seventy-two human ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/18-231-L

    authors: Mallya J,DuVall N,Brewster J,Roberts H

    更新日期:2020-05-01 00:00:00

  • Comparison of two methods of measuring dye penetration in restoration microleakage studies.

    abstract::This study compared the slice method of measuring microleakage to the whole-wall method. Forty-eight Class V direct metal restorations were placed in the buccal and lingual surfaces of 24 human molars. Following thermocycling and storage in 2% methylene blue stain for 12 hours, the teeth were sectioned and the restora...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Williams PT,Schramke D,Stockton L

    更新日期:2002-11-01 00:00:00

  • Effect of preliminary treatment of the dentin surface on the shear bond strength of resin composite to dentin.

    abstract::This study evaluated the effect of two dentin disinfectants (Consepsis, Tubulicid), one aqueous HEMA solution (Aqua Prep), a combination of Aqua Prep and Tubulicid and an air abrasion treatment (50 microns aluminum oxide) on the shear bond strength (SBS) of two acetone-based single bottle adhesives (One Step and Prime...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Pilo R,Cardash HS,Oz-Ari B,Ben-Amar A

    更新日期:2001-11-01 00:00:00

  • Effect of composite resin contamination with powdered and unpowdered latex gloves on its shear bond strength to bovine dentin.

    abstract::The aim of the present study was to evaluate the effect of composite resin contamination with powdered and unpowdered latex gloves on the shear bond strength of etch-and-rinse and two-step self-etch adhesive systems. Standard flat dentin surfaces were prepared on the facial aspect of 120 bovine incisors and randomly a...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/11-088-L

    authors: Oskoee SS,Navimipour EJ,Bahari M,Ajami AA,Oskoee PA,Abbasi NM

    更新日期:2012-09-01 00:00:00

  • Effects of secondary curing on indirect posterior composite resins.

    abstract::This study was designed to compare strength, elastic modulus (stiffness), and hardness for five composite resin materials that are used for laboratory-fabricated posterior composite restorations. Ten specimens of each material were processed according to the manufacturer's instructions. Statistical analysis indicated ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Reinhardt JW,Boyer DB,Stephens NH

    更新日期:1994-11-01 00:00:00

  • Two-year clinical comparison of a microfilled and a hybrid resin-based composite in non-carious Class V lesions.

    abstract::The purpose of this double-blind clinical trial was to compare the retention rate in noncarious Class V lesions of two resin-based composite restorative materials with contrasting stiffness. Isolation with retraction cord, pressed paper triangles, and cotton rolls was used to closely mimic the procedures generally use...

    journal_title:Operative dentistry

    pub_type: 临床试验,杂志文章,随机对照试验

    doi:

    authors: Browning WD,Brackett WW,Gilpatrick RO

    更新日期:2000-01-01 00:00:00

  • Tooth regeneration in operative dentistry.

    abstract::For many years, operative dentistry has been using regenerative approaches to treat dental disease. The use of calcium hydroxide to stimulate reparative or reactionary dentin is clearly an example of such a therapeutic strategy. The advent of tissue engineering is allowing dentistry to move forward in the use of regen...

    journal_title:Operative dentistry

    pub_type: 杂志文章,评审

    doi:10.2341/06-000

    authors: Nör JE

    更新日期:2006-11-01 00:00:00

  • Clinical evaluation of ceramic inlays and onlays fabricated with two systems: five-year follow-up.

    abstract::This study evaluated the five-year clinical performance of ceramic inlays and onlays made with two systems: sintered Duceram (Dentsply-Degussa) and pressable IPS Empress (Ivoclar Vivadent). Eighty-six restorations were placed by a single operator in 35 patients with a median age of 33 years. The restorations were ceme...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/12-039-C

    authors: Santos MJ,Mondelli RF,Navarro MF,Francischone CE,Rubo JH,Santos GC Jr

    更新日期:2013-01-01 00:00:00

  • Multidisciplinary Treatment of Complicated Crown-Root Fractures: A Case Study.

    abstract::Traumatic dental injuries usually occur among children and adolescents, with maxillary central incisors as the most often affected teeth. Complicated crown-root fractures are particularly challenging for esthetic and functional rehabilitation and often require a multidisciplinary approach. A 21-year-old male patient c...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/15-080-T

    authors: Stojanac IL,Bajkin BV,Premovic MT,Ramic BD,Petrovic LM

    更新日期:2016-11-01 00:00:00

  • Clinical comparison of bur- and laser-prepared minimally invasive occlusal resin composite restorations: two-year follow-up.

    abstract::This study evaluated the two-year clinical performance of two minimally invasive cavity preparation techniques, bur and laser, in Class I occlusal resin composite restorations. Twenty-seven patients, each having at least one pair of occlusal caries, were enrolled in this study. For each patient, one of the cavities wa...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/09-339-C

    authors: Yazici AR,Baseren M,Gorucu J

    更新日期:2010-09-01 00:00:00

  • The effect of sandblasting and different primers on shear bond strength between yttria-tetragonal zirconia polycrystal ceramic and a self-adhesive resin cement.

    abstract:PURPOSE:To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. METHODS AND MATERIALS:Y-TZP ceramic surfaces were ground flat with 600-grit silicon car...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/13-149-L

    authors: Yi YA,Ahn JS,Park YJ,Jun SH,Lee IB,Cho BH,Son HH,Seo DG

    更新日期:2015-01-01 00:00:00

  • Administration of ascorbic acid to prevent bleaching-induced tooth sensitivity: a randomized triple-blind clinical trial.

    abstract::This study evaluated the effect of ascorbic acid, 500 mg every eight hours, on bleaching-induced tooth sensitivity. A triple-blind, parallel design, and placebo-controlled randomized clinical trial was conducted on 39 adults. The pills (placebo or ascorbic acid) were administered three times per day for 48 hours; the ...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/12-483-C

    authors: de Paula EA,Kossatz S,Fernandes D,Loguercio AD,Reis A

    更新日期:2014-03-01 00:00:00

  • Enamel wetness effects on bond strength using different adhesive systems.

    abstract:OBJECTIVE:To evaluate, through the application of different dentin bonding systems, the influence of wetness on shear bond strength in enamel. METHODS:This study evaluated three etch-and-rinse adhesive systems (Scotchbond MP [used with and without primer]; Singlebond; and Prime&Bond 2.1) and two self-etching adhesive ...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/10-163-L

    authors: Furuse AY,Cunha LF,Moresca R,Paganeli G,Mondelli RF,Mondelli J

    更新日期:2011-05-01 00:00:00

  • Assessing the surface roughness of a posterior resin composite: effect of surface sealing.

    abstract::This study assessed the in vitro influence of surface sealing on the surface roughness of a posterior resin composite before and after toothbrushing. Thirty specimens (13 mm diameter x 1 mm high) were fabricated from Filtek-P60 resin composite and randomly assigned to three groups (n = 10): a non-sealed control and tw...

    journal_title:Operative dentistry

    pub_type: 临床试验,杂志文章,随机对照试验

    doi:

    authors: Takeuchi CY,Orbegoso Flores VH,Palma Dibb RG,Panzeri H,Lara EH,Dinelli W

    更新日期:2003-05-01 00:00:00

  • Longevity of low- and high-copper amalgams analyzed by preparation class, tooth site, patient age, and operator.

    abstract::The purpose of this study was to compare the long-term survivals of two low-copper and three high-copper amalgam alloys, and to analyze four clinical factors for their possible effects on the restoration survivals. Some 1476 polished restorations were placed in hospital patients by a large number of operators and asse...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Smales RJ

    更新日期:1991-09-01 00:00:00