Endodontic Access Effect on Full Contour Zirconia and Lithium Disilicate Failure Resistance.

Abstract:

OBJECTIVES:To evaluate the effect of endodontic access on the failure load resistance of both adhesively and conventionally luted, full-contour monolithic yttria-stabilized zirconium dioxide (Y-TZP) and adhesively luted lithium disilicate (LD) crowns cemented on prepared teeth. METHODS AND MATERIALS:Seventy-two human maxillary molars were prepared per respective guidelines for all-ceramic crowns with one group (n=24) restored with LD and the other (n=48) receiving Y-TZP crowns. Preparations were scanned using computer-aided design/computer-aided milling (CAD/CAM) technology, and milled crowns were sintered following manufacturer recommendations. All LD crowns and half (n=24) of the Y-TZP crowns were adhesively cemented, while the remaining Y-TZP specimens were luted using a conventional glass ionomer cement (GIC). One LD group, one Y-TZP adhesive group, and one GIC-luted group (all n=12) then received endodontic access preparations by a board-certified endodontist: the pulp chambers were restored with a dual-cure, two-step, self-etch adhesive and a dual-cure resin composite core material. The access preparations were restored using a nano-hybrid resin composite after appropriate ceramic margin surface preparation. After 24 hours, all specimens were loaded axially until failure; mean failure loads were analyzed using Mann-Whitney U test (α=0.05). RESULTS:Endodontic access did not significantly reduce the failure load of adhesively luted LD or Y-TZP crowns, but Y-TZP crowns with GIC cementation demonstrated significantly less failure load. CONCLUSIONS:These initial findings suggest that endodontic access preparation may not significantly affect failure load resistance of adhesively luted Y-TZP and LD crowns. Definitive recommendations cannot be proposed until fatigue testing and coronal seal evaluations have been accomplished.

journal_name

Oper Dent

journal_title

Operative dentistry

authors

Mallya J,DuVall N,Brewster J,Roberts H

doi

10.2341/18-231-L

subject

Has Abstract

pub_date

2020-05-01 00:00:00

pages

276-285

issue

3

eissn

0361-7734

issn

1559-2863

journal_volume

45

pub_type

杂志文章
  • Structural Integrity Evaluation of Large MOD Restorations Fabricated With a Bulk-Fill and a CAD/CAM Resin Composite Material.

    abstract:AIMS:To evaluate the effect of two composite restorative techniques (direct bulk fill vs indirect CAD/CAM) on the fracture resistance and mode of fracture of extended mesio-occlusal-distal (MOD) cavity preparations. METHODS:Fifty-one sound human mandibular third molars were divided into three groups (n=17). Extended b...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/18-013-L

    authors: Papadopoulos C,Dionysopoulos D,Tolidis K,Kouros P,Koliniotou-Koumpia E,Tsitrou EA

    更新日期:2019-05-01 00:00:00

  • Class II composite restorations: importance of cervical enamel in vitro.

    abstract:OBJECTIVE:This study evaluated the importance of enamel at the cervical margin for support and retention of a class II composite restoration in relation to fracture strength, fracture mode, and leakage. METHODS:Sixty-five newly extracted teeth were randomly divided into five groups. Within each group, standardized cla...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/10-126-L

    authors: Laegreid T,Gjerdet NR,Vult von Steyern P,Johansson AK

    更新日期:2011-03-01 00:00:00

  • An In Vitro Investigation of Anticaries Efficacy of Fluoride Varnishes.

    abstract::Most currently marketed fluoride varnishes (FVs) have not been evaluated for their effectiveness in preventing dental caries. The objective of this study was to investigate the anticaries efficacy, measured as fluoride release into artificial saliva (AS); change in surface microhardness of early enamel caries lesions;...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/18-040-L

    authors: Dehailan LA,Martinez-Mier EA,Eckert GJ,Lippert F

    更新日期:2019-09-01 00:00:00

  • Novel Microscalpels for Removing Proximal Composite Resin Overhangs on Class II Restorations.

    abstract:INTRODUCTION:Limited access to interdental spaces complicates removal of excess material when placing class II composite resin restorations. Evidence-based recommendations on interproximal finishing are rare. We present novel microscalpels for this indication. The aim of the study was to test their fracture strength an...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/16-012-L

    authors: Wolff D,Schick S,Staehle HJ,Frese C

    更新日期:2017-05-01 00:00:00

  • Influence of light activation on the volumetric change of core foundation resins.

    abstract::A core foundation system is frequently used in endodontically treated teeth that suffer excessive loss of the coronal portion of their structure. The volumetric shrinkage of core foundation resins may create marginal gaps that influence the bonding ability and longevity of a restored tooth. Little is known about how a...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Uekusa S,Miyazaki M,Rikuta A,Kurokawa H,Moore BK

    更新日期:2005-09-01 00:00:00

  • Effect of cleansing methods on saliva-contaminated zirconia--an evaluation of resin bond durability.

    abstract::The aims of this study were to investigate 1) the influence of cleansing methods after saliva contamination and 2) aging conditions (thermocycling and water storage) on zirconia shear bond strength (SBS) with a resin cement. One hundred and eighty zirconia specimens were sandblasted with 50 μm aluminum oxide particles...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/13-323-L

    authors: Feitosa SA,Patel D,Borges AL,Alshehri EZ,Bottino MA,Özcan M,Valandro LF,Bottino MC

    更新日期:2015-03-01 00:00:00

  • The effect of sandblasting and different primers on shear bond strength between yttria-tetragonal zirconia polycrystal ceramic and a self-adhesive resin cement.

    abstract:PURPOSE:To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. METHODS AND MATERIALS:Y-TZP ceramic surfaces were ground flat with 600-grit silicon car...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/13-149-L

    authors: Yi YA,Ahn JS,Park YJ,Jun SH,Lee IB,Cho BH,Son HH,Seo DG

    更新日期:2015-01-01 00:00:00

  • Clinical performance of ormocer, nanofilled, and nanoceramic resin composites in Class I and Class II restorations: a three-year evaluation.

    abstract:PURPOSE:This prospective long-term clinical trial evaluated and compared the three-year clinical performance of an ormocer, a nanofilled, and a nanoceramic resin composite with that of a microhybrid composite placed in Class I and Class II cavities. METHODS:Forty patients, each with four Class I and II restorations un...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/12-313-C

    authors: Mahmoud SH,El-Embaby AE,AbdAllah AM

    更新日期:2014-01-01 00:00:00

  • Minimally invasive treatment for esthetic management of severe dental fluorosis: a case report.

    abstract::Dental fluorosis is a developmental disturbance of enamel caused by excessive fluoride on ameloblasts during enamel formation. Patients often present to the dentist with a main goal of improving their esthetic appearance. This case report describes a minimally invasive technique for treating a severe case of enamel fl...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/12-238-S

    authors: Wang Y,Sa Y,Liang S,Jiang T

    更新日期:2013-07-01 00:00:00

  • Effects of pre-soaked retraction cords on the microcirculation of the human gingival margin.

    abstract::In the direct treatment of cervical lesions and to improve the impression-making procedure prior to fabricating indirect restorations, exposure of the gingival sulcus and control of hemorrhage or gingival fluid seepage are a prerequisite. For gingival displacement, cords impregnated with medicaments are widely used. I...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Fazekas A,Csempesz F,Csabai Z,Vág J

    更新日期:2002-07-01 00:00:00

  • Brushing abrasion of luting cements under neutral and acidic conditions.

    abstract::Four resin based materials (Compolute Aplicap, ESPE; Variolink Ultra, Vivadent; C&B Metabond, Parkell and Panavia 21, Kuraray), two carboxylate cements (Poly-F Plus, Dentsply DeTrey and Durelon Maxicap, ESPE), two glass-ionomer cements (Fuji I, GC and Ketac-Cem Aplicap, ESPE), one resin-modified glass ionomer cement (...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Buchalla W,Attin T,Hellwig E

    更新日期:2000-11-01 00:00:00

  • Repair of non-carious amalgam margin defects.

    abstract::This study investigated the microleakage associated with the repair of non-carious amalgam defects using flowable resin composite. Occlusal amalgam preparations were accomplished on 36 non-carious mandibular molars. A standardized 40-micron marginal defect was made by condensing amalgam against a mylar matrix strip. S...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Roberts HW,Charlton DG,Murchison DF

    更新日期:2001-05-01 00:00:00

  • Coronal fractures in posterior teeth.

    abstract::Coronal fractures of posterior teeth are not rare in clinical practice. Most of the time they constitute a restorational problem for the clinician, since they usually end below the free gingival crest. Two hundred coronal fractures of posterior teeth were examined in this study, with respect to several factors. Some o...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Lagouvardos P,Sourai P,Douvitsas G

    更新日期:1989-01-01 00:00:00

  • Composite photopolymerization with diode laser.

    abstract::Under clinical conditions, the time needed for the proper light curing of luting composites or the multi-incremental buildup of a large restoration with halogen curing units is quite extensive. Due to the development of high power curing devices, such as argon lasers and plasma arc lights and, in order to decrease cur...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/06-79

    authors: Knezevic A,Ristic M,Demoli N,Tarle Z,Music S,Negovetic Mandic V

    更新日期:2007-05-01 00:00:00

  • Influence of bleaching agents and desensitizing varnishes on the water content of dentin.

    abstract::This in vitro study investigated the possible dehydration of dentin caused by bleaching agents. Furthermore, it tested whether protective dentin varnishes can maintain the physiological moisture of dentin during bleaching treatment. Fifty-five standardized dentin cylinders were prepared from freshly extracted bovine i...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/05-89

    authors: Betke H,Kahler E,Reitz A,Hartmann G,Lennon A,Attin T

    更新日期:2006-09-01 00:00:00

  • The effect of energy application sequence on the microtensile bond strength of different C-factor cavity preparations.

    abstract::This study investigated the effect of three equivalent radiant exposure energy application sequences (EASs): high intensity power (HIP: 1,177 mW/cm2, 40 seconds), low intensity power (LOP: 573 mW/cm2, 71 seconds) and ramp (RMP: 650 mW/cm2, 5 seconds, then the irradiance increases to 1047 mW/cm2, 37 seconds) on the mic...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/06-30

    authors: Maghaireh G,Bouschlicher MR,Qian F,Armstrong SR

    更新日期:2007-03-01 00:00:00

  • Bulk-fill resin composites: polymerization contraction, depth of cure, and gap formation.

    abstract::The bulk-filling of deep, wide dental cavities is faster and easier than traditional incremental restoration. However, the extent of cure at the bottom of the restoration should be carefully examined in combination with the polymerization contraction and gap formation that occur during the restorative procedure. The a...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/13-324-L

    authors: Benetti AR,Havndrup-Pedersen C,Honoré D,Pedersen MK,Pallesen U

    更新日期:2015-03-01 00:00:00

  • In vivo examination of the Scotchbond Multi-Purpose Dental Adhesive System in rat (vitalmicroscopic study).

    abstract::No data are available on the direct acute vascular effect of dental bonding materials on the dental pulp. This study investigated the effects of the components of a composite resin-bonding system on pulpal vascular diameter. Three groups of 10 male Sprague-Dawley rats (weighing 330 +/- 51 g) were used for this investi...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Iványi I,Balogh AE,Rosivall L,Nyárasdy I

    更新日期:2000-09-01 00:00:00

  • Direct Posterior Restorations: A 13-Year Survey of Teaching Trends and Use of Materials.

    abstract:OBJECTIVE::The study aimed to evaluate teaching trends and use of materials in direct posterior restorations during a 13-year period in an Israeli dental school. METHODS::Data registered in computerized files, relating to posterior restorations performed in the student clinic during the past 13 years (2004-2016), were...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/17-361-C

    authors: Zabrovsky A,Mahmoud R,Beyth N,Ben-Gal G

    更新日期:2018-11-01 00:00:00

  • Barcoll hardness of different resin-based composites cured by halogen or light emitting diode (LED).

    abstract::The clinical performance of light curing resin composites is greatly influenced by the quality of the light-curing unit (LCU). Halogen LCUs are commonly used for curing composite materials. However, they have some drawbacks. The development of new, blue, super bright light emitting diodes (LED LCU) of 470-nm wavelengt...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Bala O,Uçtasli MB,Tüz MA

    更新日期:2005-01-01 00:00:00

  • Influence of Nd:YAG laser irradiation on an adhesive restorative procedure.

    abstract::Hard tissue modification by means of laser irradiation is becoming popular in dentistry, since it promotes assorted responses between the tooth and the restorative material. Some studies on the bond strength of adhesive systems to Nd:YAG irradiated teeth have shown distinctive behaviors when irradiation was applied be...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/05-110

    authors: Franke M,Taylor AW,Lago A,Fredel MC

    更新日期:2006-09-01 00:00:00

  • Effect of time and polymerization cycle on the degree of conversion of a resin composite.

    abstract::The aim of this investigation was to verify the influence of 3 light curing units on the degree of conversion, using different irradiation conditions: 1) manufacturers' recommended times of photo-activation, 2) standardizing total energy density among the units and 3) standardizing energy density at the 450-490 nm wav...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/05-81

    authors: Schneider LF,Consani S,Ogliari F,Correr AB,Sobrinho LC,Sinhoreti MA

    更新日期:2006-07-01 00:00:00

  • A suggested method for mixing direct filling restorative gallium alloy.

    abstract::Good wettability is one of the desirable physical properties of mercury-free gallium-based alloys (Gallium Alloy GF). However, wettability, while providing good adhesion to the cavity wall, has the adverse effect of causing stickiness to the inside of the capsule during mixing, and also to the metal hand instruments u...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Momoi Y,Asami Y,Ozawa M,Kohno A

    更新日期:1996-01-01 00:00:00

  • Two-year clinical evaluation of IPS Empress II ceramic onlays/inlays.

    abstract::The stronger the ceramic material, the longer the restoration stays in the mouth. The current study evaluated the two-year clinical performance of a strong ceramic system, IPS Empress II, with increased strength on onlay/inlay restorations of molars. Teeth from 35 patients, including three premolars and 32 molars, wer...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/08-97

    authors: Tagtekin DA,Ozyöney G,Yanikoglu F

    更新日期:2009-07-01 00:00:00

  • Effect of a ferrule and increased clinical crown length on the in vitro fracture resistance of premolars restored using two dowel-and-core systems.

    abstract::This study investigated the effect of a crown-lengthening ferrule on the fracture resistance of endodontically-treated teeth restored with two dowel-core systems. Thirty-two extracted mandibular first premolars were sectioned perpendicular to the long axis at a point 1.0 mm occlusal to the buccal cementoenamel junctio...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/06-169

    authors: Meng QF,Chen YM,Guang HB,Yip KH,Smales RJ

    更新日期:2007-11-01 00:00:00

  • Administration of ascorbic acid to prevent bleaching-induced tooth sensitivity: a randomized triple-blind clinical trial.

    abstract::This study evaluated the effect of ascorbic acid, 500 mg every eight hours, on bleaching-induced tooth sensitivity. A triple-blind, parallel design, and placebo-controlled randomized clinical trial was conducted on 39 adults. The pills (placebo or ascorbic acid) were administered three times per day for 48 hours; the ...

    journal_title:Operative dentistry

    pub_type: 杂志文章,随机对照试验

    doi:10.2341/12-483-C

    authors: de Paula EA,Kossatz S,Fernandes D,Loguercio AD,Reis A

    更新日期:2014-03-01 00:00:00

  • In vivo adhesive interface between resin and dentin.

    abstract::V-shaped cervical cavities prepared in monkey teeth were restored with several dentin bonding systems, and the in vivo resin-dentin interfacial structures were observed under the scanning electron microscope using an argon-ion etching technique. The hybrid layer could be clearly observed; its depth was dependent on th...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Shimada Y,Harnirattisai C,Inokoshi S,Burrow MF,Takatsu T

    更新日期:1995-09-01 00:00:00

  • Effect of mechanical properties of resin composites on the efficacy of the dentin bonding system.

    abstract::This study determined the relationship between marginal adaptation to dentin cavity preparations, tensile bond strength of the restorations, and mechanical properties of the composites. Contraction gaps, tensile bond strengths, flexural strengths, and Young's modulus of eight commercial resin composites were determine...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Hasegawa T,Itoh K,Koike T,Yukitani W,Hisamitsu H,Wakumoto S,Fujishima A

    更新日期:1999-11-01 00:00:00

  • Influence of Tooth Pigmentation on H2O2 Diffusion and Its Cytotoxicity After In-office Tooth Bleaching.

    abstract:CLINICAL RELEVANCE:Pigments in tooth structures affect the diffusion of H2O2 through enamel and dentin. The bleaching methodology can be impacted. SUMMARY:Objective: The aim of this study was to evaluate the influence of the presence of pigments in tooth structures on the trans-enamel and trans-dentin diffusion of hyd...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:10.2341/19-013-L

    authors: de Oliveira Duque CC,Soares DG,Briso A,Ortecho-Zuta U,de Oliveira Ribeiro RA,Hebling J,de Souza Costa CA

    更新日期:2020-11-01 00:00:00

  • Analysis of the degree of conversion of LED and halogen lights using micro-Raman spectroscopy.

    abstract::This study determined the degree of conversion of two LED (light-emitting diodes) (Elipar FreeLight [FL], 3M ESPE; GC e-Light [EL], GC), a high intensity (Elipar TriLight [TL], 3M ESPE) and a very high intensity (Astralis 10 [AS], Ivoclar Vivadent) halogen light. The degree of conversion of these lights was compared t...

    journal_title:Operative dentistry

    pub_type: 杂志文章

    doi:

    authors: Soh MS,Yap AU,Yu T,Shen ZX

    更新日期:2004-09-01 00:00:00