Abstract：
:This study investigated the influence of light energy density (intensity x time) on the effectiveness of composite cure in view of the curing profiles of new light-polymerization units. This investigation used a digital microhardness tester to evaluate the hardness of the top/bottom surfaces and hardness ratio of 2 mm thick composite specimens after exposure to different light energy densities. Parameters included five light intensities (200, 300, 400, 500 and 600 mW/cm2) and nine irradiation times (10, 20, 30, 40, 60, 80, 100, 120 and 180 seconds). Six samples were evaluated for each light energy density. KHN values and the hardness ratio obtained with 40 seconds cure at 400 mW/cm2 was used as control. Results were analyzed with one-way ANOVA and Scheffe's post-hoc test at significance level (0.05). Correlation between curing time and hardness values and ratio was done using Pearson's correlation at significance level 0.01. Results showed that the adequate hardness for surface finishing could be obtained with 20 seconds irradiation at lower intensities of 200 or 300 mW/cm2. Optimal cure of the bottom surfaces could not be achieved with 200 mW/cm2, but was attained with 300 mW/cm2 only after 120 seconds of irradiation. Optimal cure of the bottom surfaces was possible with 30 and 20 seconds irradiation at 500 and 600 mW/cm2, respectively. Effective cure was not achieved with low light intensities (200 to 300 mW/cm2) but could be achieved with high intensities (500 and 600 mW/cm2) after 30 seconds of irradiation.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Yap AU,Seneviratne Ckeywords:
subject
Has Abstractpub_date
2001-09-01 00:00:00pages
460-6issue
5eissn
0361-7734issn
1559-2863journal_volume
26pub_type
杂志文章abstract：:No data are available on the direct acute vascular effect of dental bonding materials on the dental pulp. This study investigated the effects of the components of a composite resin-bonding system on pulpal vascular diameter. Three groups of 10 male Sprague-Dawley rats (weighing 330 +/- 51 g) were used for this investi...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-09-01 00:00:00
abstract：:The present study investigated the effect of three high-viscosity bulk-fill resin-based composite materials on cuspal deflection in natural teeth. Thirty-two sound maxillary premolar teeth with large slot mesio-occlusal-distal cavities were distributed into four groups (n=8). Three groups were restored with bulk-fill ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-072-L
更新日期：2018-01-01 00:00:00
abstract：OBJECTIVES:This study aimed to assess the retention of metal copings luted to uremic teeth with five different luting agents. METHODS:A total of 35 sound natural molars was collected from uremic patients and randomly assigned into five groups (n=7). The teeth were prepared for metal copings using diamond tips and wate...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/12-523-LR2
更新日期：2014-05-01 00:00:00
abstract：UNLABELLED:Examining three bleaching systems, this in vivo clinical trial evaluated the relationship among tooth sensitivity, light activation, and agent concentration, and it correlated dental sensitivity with tooth thickness. MATERIALS AND METHODS:Eighty-seven volunteer patients were included. Inclusion criteria wer...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/12-335-C
更新日期：2013-09-01 00:00:00
abstract：:This study evaluated the in vivo effects of bleaching agents containing 10% carbamide peroxide (Platinum/Colgate) or 7.5% hydrogen peroxide (Day White 2Z/Discus Dental) on mutans Streptococcus during dental bleaching. The products were applied on 30 volunteers who needed dental bleaching. In each volunteer, one of the...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-07-01 00:00:00
abstract：:The antibacterial effects of the dentin bonding systems Syntac, ProBOND, Gluma 3-Step, the resin-modified glass ionomers Photac-Fil, Fuji Lining LC, Fuji II LC, and the polyacid-modified composite resins VariGlass, Geristore, and Infinity were evaluated using the cariogenic bacteria S mutans, L salivarius, S sobrinus,...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1996-11-01 00:00:00
abstract：:Under clinical conditions, the time needed for the proper light curing of luting composites or the multi-incremental buildup of a large restoration with halogen curing units is quite extensive. Due to the development of high power curing devices, such as argon lasers and plasma arc lights and, in order to decrease cur...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/06-79
更新日期：2007-05-01 00:00:00
abstract：:Standardized class 4 cavities were prepared in bovine incisors and restored with a microfilled composite resin. The composite restorations were retained either by acid etching technique (AET) alone or by acid etching technique in combination with a self-threading retentive pin. Pins covered with a bonding/opaquer coat...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-05-01 00:00:00
abstract：:This study compares volumetric changes and rates of shrinkage during different stages of polymerization of dental resin composites and compomers exposed to the same total energy by using two different combinations of power density and exposure duration. A hybrid composite and its equivalent flowable and a compomer and...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-09-01 00:00:00
abstract：:This study compared microleakage of composite bonded to etched flattened enamel in seven groups of five extracted maxillary molars. The facial enamel of the molars was ground flat and etched for 20 seconds with 37% phosphoric acid gel. In one group, etching gel was not rinsed but dried only. In four groups, gel was ri...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1993-01-01 00:00:00
abstract：:Most currently marketed fluoride varnishes (FVs) have not been evaluated for their effectiveness in preventing dental caries. The objective of this study was to investigate the anticaries efficacy, measured as fluoride release into artificial saliva (AS); change in surface microhardness of early enamel caries lesions;...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-040-L
更新日期：2019-09-01 00:00:00
abstract：:Veneers were fabricated by CEREC CAD-CAM and the platinum foil techniques for standardized preparations on 10 artificial teeth. Mesial preparation contacts were broken, but distal contacts remained intact. The veneers were cemented in a standardized manner to their teeth. The veneers and their attached cement were emb...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1997-05-01 00:00:00
abstract：CLINICAL RELEVANCE:Pigments in tooth structures affect the diffusion of H2O2 through enamel and dentin. The bleaching methodology can be impacted. SUMMARY:Objective: The aim of this study was to evaluate the influence of the presence of pigments in tooth structures on the trans-enamel and trans-dentin diffusion of hyd...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-013-L
更新日期：2020-11-01 00:00:00
abstract：:This investigation examined the susceptibility to staining and translucency changes of some new tooth-colored restorative materials after immersion in different beverages. The materials studied were 3M Filtek Z350XT (ZT), 3M Filtek 350XT Flowable Restorative (ZF), Shofu Beautifil Flow Plus (BF), Shofu Beautifil II (B2...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/149027-L
更新日期：2015-03-01 00:00:00
abstract：:This study evaluated the degree of conversion (%DC) of luting agents around ceramic inlays placed in deep natural cavities. Thirty-six cylindrical Class I cavities (diameter = 4 mm, depth = 4 mm) were prepared in freshly extracted human teeth and randomly divided according to the luting materials used for luting CAD/C...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/10-012-L
更新日期：2010-09-01 00:00:00
abstract：:Provisional restorations of full crown preparations may permit more microleakage of bacteria and their products than the final castings do. However, most investigations of the sealing qualities of cemented castings have reported that they too permit dye leakage. One approach to the problem is to seal the dentin with d...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1992-01-01 00:00:00
abstract：:This study compared the viscoelastic properties of restorative and flowable bulk-fill resin-based composites (RBCs) with their conventional counterparts and evaluated the impact of aqueous solutions on viscoelastic properties. The materials examined included three conventional RBCs (Filtek Z350, Tetric N Ceram, and Be...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-005-L
更新日期：2020-03-01 00:00:00
abstract：OBJECTIVE:To evaluate the effect of mechanical loading on the microtensile bond strength (MTBS) of five adhesive systems to dentin. METHODS:Flat dentin surfaces from human molars were divided into five groups and bonded with total-etch self-priming adhesives (Single Bond, Prime&Bond NT and Prime&Bond XP), two-step sel...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/04-161
更新日期：2006-01-01 00:00:00
abstract：:Traumatic dental injuries usually occur among children and adolescents, with maxillary central incisors as the most often affected teeth. Complicated crown-root fractures are particularly challenging for esthetic and functional rehabilitation and often require a multidisciplinary approach. A 21-year-old male patient c...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-080-T
更新日期：2016-11-01 00:00:00
abstract：:This in vitro study compared the marginal and internal adaptation of bulk-filled Class I and cuspal coverage direct resin composite restorations filled with different types of adhesive restorative systems and different thicknesses of bonding agent. Seventy-two intact, caries-free, freshly extracted human molars were r...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-157
更新日期：2007-09-01 00:00:00
abstract：:This in vitro study measured cusp deflection associated with MOD resin composite restorations in maxillary premolars with different curing light modes. Soft-start polymerization may reduce cusp deflection by reducing polymerization shrinkage stress. Forty maxillary premolars were mounted in stone and slot MOD cavities...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：
更新日期：2005-11-01 00:00:00
abstract：:This review compares nine published studies conducted at the Indiana University School of Dentistry. Twenty-five products in four different systems were evaluated using the Trubyte Bioform Color Ordered Shade Guide and a Chroma Meter. The dentist-prescribed overnight bleaching delta mean shade guide value (DSGV) 10 we...
journal_title：Operative dentistry
pub_type： 杂志文章,评审
doi：10.2341/08-74
更新日期：2009-03-01 00:00:00
abstract：:The molar proximal half-crown cast gold restoration may be an ideal choice for the conservative treatment of teeth with only one compromised proximal aspect. ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/10-T1
更新日期：2010-03-01 00:00:00
abstract：:The aim of this study was to determine whether using a silane-containing universal adhesive as a silane primer in glass-ceramic/resin cement systems affects biaxial flexural strength (BFS) and bonded interface integrity after loading. Glass-ceramic (IPS e.max CAD, Ivoclar/Vivadent, Schaan, Liechtenstein) disc-shaped s...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-356-L
更新日期：2019-03-01 00:00:00
abstract：:This study compared the surface finish of eight different types of aesthetic restorative materials. The materials included resin-modified (Fuji II LC [FL], GC) and highly viscous (Fuji IX GP Fast [FN], GC) glass ionomer cements, a compomer (F2000 [FT], 3M-ESPE), minifilled (Z100 [ZO], 3M-ESPE) and microfilled (A110 [A...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-01-01 00:00:00
abstract：:While a one-year report had been previously published, this study was undertaken to evaluate the clinical performance and appearance of a resin-modified glass ionomer and a resin composite over two years. Thirty-seven pairs of restorations of FujI II LC and Z 250/Single Bond were placed in caries-free cervical erosion...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2003-09-01 00:00:00
abstract：:Coronal fractures of posterior teeth are not rare in clinical practice. Most of the time they constitute a restorational problem for the clinician, since they usually end below the free gingival crest. Two hundred coronal fractures of posterior teeth were examined in this study, with respect to several factors. Some o...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1989-01-01 00:00:00
abstract：OBJECTIVE:The aim of the study was to compare in Class V composite restorations marginal leakage measurements obtained with microcomputed tomography (micro-CT) and scanning electron microscopy (SEM) observations. METHODS:Class V cavities were prepared on 10 human molars and restored using Optibond FL (Kerr, Orange, CA...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/14-022-L
更新日期：2015-07-01 00:00:00
abstract：OBJECTIVE:To evaluate, through the application of different dentin bonding systems, the influence of wetness on shear bond strength in enamel. METHODS:This study evaluated three etch-and-rinse adhesive systems (Scotchbond MP [used with and without primer]; Singlebond; and Prime&Bond 2.1) and two self-etching adhesive ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/10-163-L
更新日期：2011-05-01 00:00:00
abstract：:Bleaching-induced tooth sensitivity (TS) is highly prevalent. OBJECTIVE:This study aimed to determine if the combination of opioids and nonopioids analgesics (Tylex) may provide a better analgesic effect. METHOD:A triple-blind, parallel, randomized two-center clinical trial was conducted with 105 healthy patients wh...
journal_title：Operative dentistry
pub_type： 杂志文章,多中心研究,随机对照试验
doi：10.2341/17-092-C
更新日期：2018-03-01 00:00:00
