Abstract：
:This in vitro study evaluated the wear resistance of resin composite polymerized using four different light-curing systems. For this, a well-defined cylindrical cavity preparation (4.0 mm in diameter x 3.0 mm in depth) was made in a ceramic block (n=4 per material/light condition). Uncured material, either a universal hybrid composite (Herculite XRV) or a flowable hybrid composite (Revolution Formula 2), was packed and light-cured from the top surface only with one of the four light-curing units: 1) a conventional quartz-tungsten-halogen light, 2) a soft-start light, 3) an argon-ion laser or 4) a plasma-arc curing light. After storing the specimens in deionized water at 37 degrees C for 24 hours, the excess cured material was ground through successive grits up to a final 1200-grit SiC abrasive. The specimens were placed in deionized water at 37 degrees C for an additional 24 hours. Wear simulation was performed using a four-station Leinfelder-type three-body wear device. A slurry of water and unplasticized polymethylmethacrylate beads, simulating an artificial food bolus, was placed on the surface of each resin-composite-restored ceramic block. The entire cycling procedure was carried out 400,000 times. Impressions of each resin composite surface were taken with polyvinylsiloxane and epoxy replicas were made. Wear analyses were conducted by generating tracings across the worn surface of epoxy replicas using profilometer scans. For the universal hybrid composite and the flowable hybrid composite, the lowest wear occurred in specimens that were cured using the conventional quartz-tungsten-halogen light, and the highest wear was detected on those specimens made using the argon-ion laser. For both resin composites, the mean wear for specimens cured using the argon-ion laser was significantly higher than that of the specimens cured with the three other lights, which were statistically similar.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
St-Georges AJ,Swift EJ Jr,Thompson JY,Heymann HOkeywords:
subject
Has Abstractpub_date
2002-07-01 00:00:00pages
410-7issue
4eissn
0361-7734issn
1559-2863journal_volume
27pub_type
杂志文章abstract：:This in vitro study evaluated the interfacial integrity of Class II resin composite restorations. The influence of a flowable composite and additional enamel etching was also evaluated. Deep, saucer-shaped Class II cavities were prepared in the mesial and distal proximal surfaces of 25 extracted human molars and assig...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2001-01-01 00:00:00
abstract：:A study was conducted to compare the shear bond strength of a glass-ionomer cement and glass-ionomer base to coronal and radicular dentin. Two different glass ionomers were bonded to paired coronal and radicular human dentin surfaces that had received no surface treatment or had been treated passively for 20 seconds w...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-07-01 00:00:00
abstract：CLINICAL RELEVANCE:Computer-aided design/computer-aided manufacturing (CAD/CAM) composite resins are susceptible to degradation by dietary solvents. Dietary counselling is prudent when placing such CAD/CAM restorations. SUMMARY:This study determined the effect of dietary solvents on the surface roughness (Ra) of direc...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-070-L
更新日期：2020-07-01 00:00:00
abstract：PURPOSE::The purpose of this study was to quantify the relative strength tolerance of 1-day and 30-day amalgam following saturation contamination with water, saliva, blood, and handpiece lubricant oil during condensation. METHODS AND MATERIALS::Valiant PhD XT amalgam was tested with 300 shear-strength (N=15) and 120 c...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-091-L
更新日期：2019-03-01 00:00:00
abstract：OBJECTIVE:This study evaluated the importance of enamel at the cervical margin for support and retention of a class II composite restoration in relation to fracture strength, fracture mode, and leakage. METHODS:Sixty-five newly extracted teeth were randomly divided into five groups. Within each group, standardized cla...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/10-126-L
更新日期：2011-03-01 00:00:00
abstract：OBJECTIVES:It has been reported that bleaching generates an increase in the activity of osteoclasts in vitro. We quantified the RANK-L and IL-1β biomarkers in a double-blind, randomized clinical trial evaluating the in vivo effect of hydrogen peroxide (35%) and peroxide carbamide (37%) six months after whitening. METH...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/18-023-C
更新日期：2019-11-01 00:00:00
abstract：OBJECTIVES:To evaluate the clinical behavior of one-piece complete-coverage crowns and fixed partial dentures (FPDs) on teeth with vertical preparation without finish line biologically oriented preparation technique (BOPT). METHODS AND MATERIALS:This prospective study included 52 patients requiring treatment with rest...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-124-C
更新日期：2018-09-01 00:00:00
abstract：:The tested hypotheses of this study were that dentin enamel bonding agents (DBAs) proposed for compomers create a hybrid layer (HL) that seals the margins of Class V restorations and HL is free from voids or gaps on both enamel and dentin margins. For purposes of this study, Class V restorations (n = 70) were made in ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-01-01 00:00:00
abstract：:This study determined the influence of light curing protocols and matrix type on the margin quality and marginal seal of Class II resin-based composite restorations. In extracted human molars, box-shaped MOD cavities with 1 mm wide interproximal bevels were prepared with cervical margins located at least 1 mm coronal ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/04-194
更新日期：2006-01-01 00:00:00
abstract：CLINICAL RELEVANCE:Pigments in tooth structures affect the diffusion of H2O2 through enamel and dentin. The bleaching methodology can be impacted. SUMMARY:Objective: The aim of this study was to evaluate the influence of the presence of pigments in tooth structures on the trans-enamel and trans-dentin diffusion of hyd...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-013-L
更新日期：2020-11-01 00:00:00
abstract：:In some patients with labial white stains involving the enamel and dentin, bleaching associated with a restorative procedure using composites may be an appropriate treatment alternative. Although bleaching makes the teeth and the stain whiter, the staining is less evident and easier to restore. Restorative procedures ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/12-284-T
更新日期：2013-07-01 00:00:00
abstract：:The present clinical case report describes the clinical steps of enamel microabrasion associated with dental bleaching to restore severely-pitted fluorosed teeth. The process of removing the fluorotic superficial stains started by using macroabrasion with a water-cooled fine tapered 3195 FF diamond bur. Rubber dam iso...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-116-T
更新日期：2019-11-01 00:00:00
abstract：:For many years, operative dentistry has been using regenerative approaches to treat dental disease. The use of calcium hydroxide to stimulate reparative or reactionary dentin is clearly an example of such a therapeutic strategy. The advent of tissue engineering is allowing dentistry to move forward in the use of regen...
journal_title：Operative dentistry
pub_type： 杂志文章,评审
doi：10.2341/06-000
更新日期：2006-11-01 00:00:00
abstract：:This study compared the viscoelastic properties of restorative and flowable bulk-fill resin-based composites (RBCs) with their conventional counterparts and evaluated the impact of aqueous solutions on viscoelastic properties. The materials examined included three conventional RBCs (Filtek Z350, Tetric N Ceram, and Be...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-005-L
更新日期：2020-03-01 00:00:00
abstract：:This study compared the post-gel contraction of two "low-shrinkage" composites (InTen-S [IS], Ivoclar-Vivadent; Aelite LS [AL], BISCO Inc) and an ormocer (Admira [AM], Voco) to two conventional mini-filled composites (Renew [RN], BISCO; Z100 [ZO], 3M ESPE). A strain-monitoring device and test configuration were used t...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-03-01 00:00:00
abstract：:This study evaluated the shear bond strength of repairs made with a composite (Herculite/Kerr) when two different surface treatment methods and two new generation bond materials were used. The bonding surfaces were prepared by sanding with 500-grit aluminum oxide sandpaper or air abrading with 25-micron aluminum oxide...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-03-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate the effects of different desensitizing agents on the prevention of root caries when applied to root surfaces. MATERIALS AND METHODS:Thirty human roots were sectioned into quarters with a 3 × 4 mm window. A desensitizer (VX, Clinpro™ XT Varnish; SP, Seal & Protect®; o...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-007-L
更新日期：2012-05-01 00:00:00
abstract：OBJECTIVES:To evaluate the effect of application protocol in resin-enamel microshear bond strength (μSBS), in situ degree of conversion, and etching pattern of three universal adhesive systems. METHODS AND MATERIALS:Sixty-three extracted third molars were sectioned in four parts (buccal, lingual, and proximals) and di...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-213-L
更新日期：2016-09-01 00:00:00
abstract：:This study evaluated the two-year clinical performance of two minimally invasive cavity preparation techniques, bur and laser, in Class I occlusal resin composite restorations. Twenty-seven patients, each having at least one pair of occlusal caries, were enrolled in this study. For each patient, one of the cavities wa...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/09-339-C
更新日期：2010-09-01 00:00:00
abstract：OBJECTIVES:Whitening efficacy has been related to hydrogen peroxide (HP) diffusion into tooth structure. However, little information is available relating rheological properties to whitening efficacy. The purpose was to evaluate the whitening efficacy and HP penetration level of a 10% HP gel at three different viscosit...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/17-099-L
更新日期：2018-05-01 00:00:00
abstract：:The effect of interdental separation of a special separation ring and wooden wedge was investigated. In a split-mouth design, 27 patients were randomly assigned to one of two groups (W or S). In 11 patients, an interdental wooden wedge (Hawe-Neos) was placed (group W), and in 16 patients, a separation ring (Composi-Ti...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-73
更新日期：2007-05-01 00:00:00
abstract：:This study investigated the effects of an at-home bleaching gel containing 15% carbamide peroxide on the susceptibility of tooth-colored restorative materials to different staining solutions. The tooth-colored restoratives used in this study were a nano resin composite (Filtek Z350), a packable resin composite (Filtek...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/08-42
更新日期：2009-01-01 00:00:00
abstract：:A fundamental issue of restorative treatment is assessing the different conditions of cases not only from tooth-to-tooth but also from the activity of each caries lesion and the size of the cavity. In addition, restorative treatment is sometimes carried out for prosthetic and cosmetic purposes and involves cutting sou...
journal_title：Operative dentistry
pub_type：
doi：
更新日期：2002-05-01 00:00:00
abstract：:SmartPrep is a rotating instrument for dentin caries excavation made from a special polymer. The manufacturer's product information stated that SmartPrep removes carious dentin selectively. This in vitro study compared the efficiency of SmartPrep with conventional tungsten carbide bud burs. Fifty extracted teeth were ...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/05-24
更新日期：2006-03-01 00:00:00
abstract：:This study investigated the influence of different light sources associated with a transdental photoactivation technique on the marginal adaptation and hardness of composite restorations. Cavities (3 mm wide x 3 mm long x 1.5 mm in deep) were prepared on flattened bovine dentin and filled with Z250 composite (3M ESPE)...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/07-109
更新日期：2008-07-01 00:00:00
abstract：:This study evaluated the five-year clinical performance of ceramic inlays and onlays made with two systems: sintered Duceram (Dentsply-Degussa) and pressable IPS Empress (Ivoclar Vivadent). Eighty-six restorations were placed by a single operator in 35 patients with a median age of 33 years. The restorations were ceme...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/12-039-C
更新日期：2013-01-01 00:00:00
abstract：PURPOSE:To investigate the effect of different light exposure times, shades, and thicknesses on the depth of cure (DOC) of bulk fill composites. METHODS AND MATERIALS:Two bulk fill composites, Tetric EvoCeram Bulk Fill (TBF) and Sonic Fill (SF), and a conventional composite, Filtek Supreme Ultra (FSU), were evaluated....
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-057-L
更新日期：2017-09-01 00:00:00
abstract：:This study evaluated the microleakage of resin-modified glass ionomer, flowable compomer and flowable resin composite restorations on a Class V cavity of simulated advanced root caries under a flexural load cycling condition. Thirty-six non-carious human maxillary premolars were mounted in cylindrical acrylic resin mo...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-03-01 00:00:00
abstract：:Excessive etching of the dentin may decrease bond strength because the adhesive may fail to completely infiltrate to the base of the over-etched demineralized collagen network. The purpose of the present study was to evaluate the influence of increasing etching times on the microtensile bond strength of Single Bond an...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1999-05-01 00:00:00
abstract：:To evaluate the correlation between microtensile dentin bond strength (microTBS) and silver ion penetration, two total-etch 3-step and one self-etch 2-step system were investigated. OptiBond FL adhesive was applied to flat occlusal dentin on six non-carious human molars, and a resin composite "crown" was formed in 2 m...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-01-01 00:00:00
