Coating thickness affects surface stress measurement of brush electro-plating nickel coating using Rayleigh wave approach.

Abstract:

:A surface ultrasonic wave approach was presented for measuring surface stress of brush electro-plating nickel coating specimen, and the influence of coating thickness on surface stress measurement was discussed. In this research, two Rayleigh wave transducers with 5MHz frequency were employed to collect Rayleigh wave signals of coating specimen with different static tensile stresses and different coating thickness. The difference in time of flight between two Rayleigh wave signals was determined based on normalized cross correlation function. The influence of stress on propagation velocity of Rayleigh wave and the relationship between the difference in time of flight and tensile stress that corresponded to different coating thickness were discussed. Results indicate that inhomogeneous deformation of coating affects the relationship between the difference in time of flight and tensile stress, velocity of Rayleigh wave propagating in coating specimen increases with coating thickness increasing, and the variation rate reduces of difference in time of flight with tensile stress increasing as coating thickness increases.

journal_name

Ultrasonics

journal_title

Ultrasonics

authors

Liu B,Dong S,Xu B,He P

doi

10.1016/j.ultras.2012.02.003

subject

Has Abstract

pub_date

2012-09-01 00:00:00

pages

861-5

issue

7

eissn

0041-624X

issn

1874-9968

pii

S0041-624X(12)00035-2

journal_volume

52

pub_type

杂志文章
  • Investigating ultrasound-induced acoustic softening in aluminum and its alloys.

    abstract::Ultrasonic vibration has been observed to lower the flow stress necessary to initiate plastic deformation, a phenomenon known as "acoustic softening". This unique effect of ultrasound has been extensively applied in welding, machining, forming of metals, and ultrasonic additive manufacturing to lower the yield stress ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.106005

    authors: Mao Q,Coutris N,Rack H,Fadel G,Gibert J

    更新日期:2020-03-01 00:00:00

  • Numerical predictions and experiments for optimizing hidden corrosion detection in aircraft structures using Lamb modes.

    abstract::To increase the sensitivity of Lamb waves to hidden corrosion in aircraft structures, a preliminary step is to understand the phenomena governing this interaction. A hybrid model combining a finite element approach and a modal decomposition method is used to investigate the interaction of Lamb modes with corrosion pit...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2007.02.004

    authors: Terrien N,Royer D,Lepoutre F,Déom A

    更新日期:2007-06-01 00:00:00

  • Potential of ultrasonic pulse velocity for evaluating the dimensional stability of oak and chestnut wood.

    abstract::The objective of this study was to examine the potential of ultrasonic velocity as a rapid and nondestructive method to predict the dimensional stability of oak (Quercus petraea (Mattuschka) Lieblein) and chestnut (Castanea sativa Mill.) that are commonly used in flooring industry. Ultrasonic velocity, specific gravit...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2015.11.007

    authors: Dündar T,Wang X,As N,Avcı E

    更新日期:2016-03-01 00:00:00

  • Guided waves in anisotropic and quasi-isotropic aerospace composites: three-dimensional simulation and experiment.

    abstract::Three-dimensional (3D) elastic wave simulations can be used to investigate and optimize nondestructive evaluation (NDE) and structural health monitoring (SHM) ultrasonic damage detection techniques for aerospace materials. 3D anisotropic elastodynamic finite integration technique (EFIT) has been implemented for ultras...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.05.007

    authors: Leckey CA,Rogge MD,Raymond Parker F

    更新日期:2014-01-01 00:00:00

  • Picosecond acoustics method for measuring the thermodynamical properties of solids and liquids at high pressure and high temperature.

    abstract::Based on the original combination of picosecond acoustics and diamond anvils cell, recent improvements to accurately measure hypersonic sound velocities of liquids and solids under extreme conditions are described. To illustrate the capability of this technique, results are given on the pressure and temperature depend...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.04.011

    authors: Decremps F,Gauthier M,Ayrinhac S,Bove L,Belliard L,Perrin B,Morand M,Le Marchand G,Bergame F,Philippe J

    更新日期:2015-02-01 00:00:00

  • Development of an ultrasonic linear motor with ultra-positioning capability and four driving feet.

    abstract::This paper presents a novel linear piezoelectric motor which is suitable for rapid ultra-precision positioning. The finite element analysis (FEA) was applied for optimal design and further analysis, then experiments were conducted to investigate its performance. By changing the input signal, the proposed motor was fou...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.07.010

    authors: Zhu C,Chu X,Yuan S,Zhong Z,Zhao Y,Gao S

    更新日期:2016-12-01 00:00:00

  • New nonlinear ultrasonic method for material characterization: Codirectional shear horizontal guided wave mixing in plate.

    abstract::A nonlinear ultrasonic method is proposed based on a group of newly discovered wave triplets where two primary codirectional shear-horizontal SH0 waves mix in a weakly nonlinear plate and generate a cumulative S0 Lamb wave at the sum frequency. Theoretical analyses show that any combination of two primary SH0 waves wh...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.04.001

    authors: Shan S,Hasanian M,Cho H,Lissenden CJ,Cheng L

    更新日期:2019-07-01 00:00:00

  • A new topological structure for the Langevin-type ultrasonic transducer.

    abstract::In this paper, a new topological structure for the Langevin-type ultrasonic transducer is proposed and investigated. The two cylindrical terminal blocks are conically shaped with four supporting plates each, and two cooling fins are disposed at the bottom of terminal blocks, adjacent to the piezoelectric rings. Experi...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.11.008

    authors: Lu X,Hu J,Peng H,Wang Y

    更新日期:2017-03-01 00:00:00

  • Two approaches to multiple specular echo detection using split spectrum processing: moving bandwidth minimization and mathematical morphology.

    abstract::A split spectrum processing technique using a novel moving bandwidth minimization (MBM) method was developed to detect multiple specular targets having different spectral characteristics. Mathematical morphology (MM) algorithms were also implemented in order to compare the results. An experimental approach to optimal ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00024-4

    authors: Grevillot M,Cudel C,Meyer JJ,Jacquey S

    更新日期:1999-09-01 00:00:00

  • Nonlinear surface acoustic waves: realization of solitary pulses and fracture.

    abstract::A laser-based technique for the contact-free generation and detection of strongly nonlinear surface acoustic wave (SAW) pulses with amplitudes limited by the materials strength has been developed. The effects of nonlinear propagation of short elastic surface pulses with finite strength in isotropic solids, such as fus...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2008.06.002

    authors: Lomonosov AM,Hess P

    更新日期:2008-11-01 00:00:00

  • Impact of localized inhomogeneity on the surface-wave velocity and bulk-wave reflection in solids.

    abstract::The effect of a weak surface, near-surface and interfacial inhomogeneity on the frequency dependence of the surface wave velocity and of the SH (shear horizontal) wave reflectivity in isotropic elastic media is studied analytically and numerically. The inhomogeneity is modeled as an infinite planar layer with continuo...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.09.001

    authors: Baron C,Shuvalov AL,Poncelet O

    更新日期:2007-03-01 00:00:00

  • Characterization of air-coupled ultrasound transducers in the frequency range 40 kHz-2 mHz using light diffraction tomography.

    abstract::The aim of this work was to show the applicability of light diffraction tomography on airborne ultrasound in the frequency range 40 kHz-2 MHz. Seven different air-coupled transducers were measured to show the method's performance regarding linearity, absolute pressure measurements, phase measurements, frequency respon...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00168-7

    authors: Almqvist M,Holm A,Persson HW,Lindström K

    更新日期:2000-01-01 00:00:00

  • Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement.

    abstract::The estimation of clamping force has been regarded as the main issue in the maintenance of high-tension bolts. This paper proposes a method which uses the dependency of ultrasonic velocity on stress based on the nonlinear elastic effect. The variation of ultrasonic velocity in the range of actual stress acting in the ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.190

    authors: Jhang KY,Quan HH,Ha J,Kim NY

    更新日期:2006-12-22 00:00:00

  • Ultrasound transmission tomography image distortions caused by the refraction effect

    abstract::This paper presents the influence of ultrasonic beam ray refraction effect on the internal object structure imaging using the ultrasound transmission tomography method (UTT), in parallel ray projection geometry, for ultrasonic pulse run-time measurements. Simulation calculations carried out using specially elaborated ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00137-7

    authors: Opielinski KJ,Gudra T

    更新日期:2000-03-01 00:00:00

  • Effect of wood properties on within-tree variation in ultrasonic wave velocity in softwood.

    abstract::The radial variations in the velocity of longitudinal waves propagating through Japanese cedar and Japanese cypress were experimentally investigated. In addition, the tracheid length (TL), microfibril angle (MFA), air-dried density (AD), and moisture content (MC) were measured in order to determine the effect of wood ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2010.10.001

    authors: Hasegawa M,Takata M,Matsumura J,Oda K

    更新日期:2011-04-01 00:00:00

  • Phonophoresis: an in vivo evaluation using three topical anaesthetic preparations.

    abstract::An electrical sensory perception threshold technique has been developed for use with human volunteers. This technique has been used to reproducibly quantify the effects of three different commercially available topical anaesthetic preparations on superficial sensory cells (nociceptors) in the skin. Low intensities (0....

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(90)90075-y

    authors: Williams AR

    更新日期:1990-05-01 00:00:00

  • Characteristic model of travelling wave ultrasonic motor.

    abstract::In general, the design and analysis of ultrasonic motor and motor's control strategy are based on mathematical model. The academic model is widely used in the analysis of traveling wave ultrasonic motor (TWUSM). But the dispersive characteristic of piezoelectric ceramics and other complicated process, such as the fric...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.09.012

    authors: Jingzhuo S,Dongmei Y

    更新日期:2014-02-01 00:00:00

  • Extraction and filtering in ultrasonic field: finite element modelling and simulation of the processes

    abstract::In this research, the use of powerful sonification is studied in making the extraction of tannins more efficient. A combined extraction-filtration system using sonification was designed and modelled. Preliminary extraction studies were carried out to show the effect of ultrasound in extraction. In these experiments hi...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00163-8

    authors: Mantysalo M,Mantysalo E

    更新日期:2000-03-01 00:00:00

  • Generation of sub-microsecond quasi-unipolar pressure pulses.

    abstract::We present a method to generate sub-microsecond quasi-unipolar pressure pulses. Our approach is based on the laser irradiation of a thin copper wire submerged in water. The acoustic waveforms were recorded using two different, well characterized, wideband detection techniques: piezoelectric and optical interferometry....

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.05.002

    authors: González MG,Riobó LM,Ciocci Brazzano L,Veiras FE,Sorichetti PA,Santiago GD

    更新日期:2019-09-01 00:00:00

  • Aperture and element minimization in linear sparse arrays with desired beam patterns

    abstract::In this paper, an optimization method aimed at designing aperiodic linear sparse arrays is proposed that is based on the stochastic optimization methodology called simulated annealing. Such a method optimizes the positions and the weight coefficients of each element of a linear array in order to obtain a beam pattern ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00089-x

    authors: Trucco A

    更新日期:2000-03-01 00:00:00

  • Y-shaped jets driven by an ultrasonic beam reflecting on a wall.

    abstract::This paper presents an original experimental and numerical investigation of acoustic streaming driven by an acoustic beam reflecting on a wall. The water experiment features a 2 MHz acoustic beam totally reflecting on one of the tank glass walls. The velocity field in the plane containing the incident and reflected be...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.02.003

    authors: Moudjed B,Botton V,Henry D,Millet S,Ben Hadid H

    更新日期:2016-05-01 00:00:00

  • A theoretical analysis of a piezoelectric ultrasound device with an active matching layer.

    abstract::This paper investigates the use of magnetically active materials in the matching layer of a piezoelectric transducer. This then allows the performance of the device to be dynamically altered by applying an external field. The effect that this new matching layer has on the performance of a typical device is theoretical...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2007.08.002

    authors: Mulholland AJ,O'Leary RL,Ramadas N,Parr A,Troge A,Pethrick RA,Hayward G

    更新日期:2007-12-01 00:00:00

  • SH ultrasonic guided waves for the evaluation of interfacial adhesion.

    abstract::Shear-Horizontally (SH) polarized, ultrasonic, guided wave modes are considered in order to infer changes in the adhesive properties at several interfaces located within an adhesive bond joining two metallic plates. Specific aluminium lap-joint samples were produced, with different adhesive properties at up to four in...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.03.002

    authors: Castaings M

    更新日期:2014-09-01 00:00:00

  • Acoustic source localization in a highly anisotropic plate with unknown orientation of its axes of symmetry and material properties with numerical verification.

    abstract::Development of acoustic source localization techniques in anisotropic plates has gained attention in the recent past and still has scope of improvement. Most of such techniques existing in the literature either require known material properties or assume a straight line propagation of wave energy from the acoustic sou...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.105977

    authors: Sen N,Kundu T

    更新日期:2020-01-01 00:00:00

  • Mössbauer and X-ray studies of Fe-powder mechanically alloyed with C using power ultrasonics.

    abstract::The Mössbauer and X-rays analysis of as-received Fe-powder and Fe-powder mechanically alloyed with C using high power ultrasonics were carried out. The powder blend of Fe-powder and graphite was processed in He environment during 5 to 50 h. The dissolution of carbon in iron particles and inhomogeneous distribution of ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.01.002

    authors: Nadutov VM,Mordyuk BN,Prokopenko GI,Gavrilenko IS

    更新日期:2004-04-01 00:00:00

  • Microparticle manipulation in millimetre scale ultrasonic standing wave chambers.

    abstract::Ultrasonic standing wave chambers with acoustic pathlengths of 1.1 and 0.62 mm have been constructed. The chambers were driven at frequencies over the range 0.66-12.2 MHz. The behaviour of 2 microns diameter latex microparticles and 5 microns diameter yeast in the chambers has been elucidated. One (flow) chamber had a...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(98)00019-5

    authors: Hawkes JJ,Barrow D,Coakley WT

    更新日期:1998-08-01 00:00:00

  • The peculiarities of the Bleustein-Gulyaev wave propagation in structures containing conductive layer.

    abstract::As known, anomalous resisto-acoustic effect is a fundamental property for weakly inhomogeneous piezoactive waves (Bleustein-Gulyaev, Love, and some leaky waves). It consists in that the velocity of aforementioned waves first increases, achieves its maximum, and only then decreases with increasing conductance of a laye...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2015.01.007

    authors: Kuznetsova IЕ,Zaitsev BD

    更新日期:2015-05-01 00:00:00

  • Sonothrombolysis with magnetic microbubbles under a rotational magnetic field.

    abstract::Thrombosis is an extremely critical clinical condition where a clot forms inside a blood vessel which blocks the blood flow through the cardiovascular system. Previous sonothrombolysis methods using ultrasound and microbubbles (MBs) often have a relatively low lysis rate due to the low microbubbles concentration at cl...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.06.004

    authors: Zhang B,Kim H,Wu H,Gao Y,Jiang X

    更新日期:2019-09-01 00:00:00

  • The nonlinear S0 Lamb mode in a plate with a linearly-varying thickness.

    abstract::The aim of this paper is to investigate propagation characteristics and the generation mechanism of the nonlinear lowest-order symmetric Lamb mode (S0) which propagates downslope in free elastic plates with slowly linearly varying-thickness. From theoretical analyses, in a low frequency-thickness product (fd) range, t...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2018.11.013

    authors: Hu Z,An Z,Kong Y,Lian G,Wang X

    更新日期:2019-04-01 00:00:00

  • Ultrasonic evaluation of microwave-induced thermal lesions based on wavelet analysis of mean scatterer spacing.

    abstract::The microwave ablation has become an important manner for tumor treatment. In this paper, we proposed a new method for evaluation of microwave-induced thermal lesions using the wavelet analysis of the mean scatterer spacing (MSS). First, the ultrasonic radiofrequency (RF) data of normal and coagulated porcine liver ti...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.03.018

    authors: Zhou Z,Sheng L,Wu S,Yang C,Zeng Y

    更新日期:2013-09-01 00:00:00