Abstract：
OBJECTIVE:To evaluate the influence of chlorhexidine with different application methods on the microtensile bond strength (microTBS) to dentin in Class I cavities. METHODS:Flat dentinal surfaces with Class I cavities (4 mm long, 4 mm wide, 2 mm deep) in 50 molars were bonded with Adper Single Bond 2 etch-and-rinse adhesive system after: 1) Chlorhexidine (CHX) + rinsing + etching; 2) CHX + no rinsing + etching; 3) Etching + CHX + rinsing; 4) Etching + CHX + no rinsing; 5) Etching only as a control group. Resin composite buildups were constructed with Z-350 (3M ESPE) using a bulk method and they were polymerized for 40 seconds. For each condition, half of the specimens were immediately submitted to microtensile bond strength and half of the same group was submitted to 10,000 cycles of thermocycling between 5 degrees C and 55 degrees C before testing. The data were analyzed using the two-way ANOVA and Student t-test at a 95% significance level. RESULTS:Chlorhexidine pretreatment did not affect the bond strength of specimens tested at the immediate testing period, regardless of the application method used, compared to the control group. However, after 10,000 thermocycles, a significant bond strength reduction was found in the control group. In general, the chlorhexidine application method did not demonstrate a significant difference among the groups treated with chlorhexidine. However, there was a significant difference after thermocycling in the groups treated with chlorhexidine before etching and no significant difference in the groups treated with chlorhexidine after etching. CONCLUSION:Considering the amount of reduction in bond strength after thermocycling, the current study showed improved dentin bond strength with chlorhexidine when used after etching.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Chang YE,Shin DHdoi
10.2341/09-360-Lsubject
Has Abstractpub_date
2010-11-01 00:00:00pages
618-23issue
6eissn
0361-7734issn
1559-2863journal_volume
35pub_type
杂志文章,随机对照试验abstract：OBJECTIVES:It has been reported that bleaching generates an increase in the activity of osteoclasts in vitro. We quantified the RANK-L and IL-1β biomarkers in a double-blind, randomized clinical trial evaluating the in vivo effect of hydrogen peroxide (35%) and peroxide carbamide (37%) six months after whitening. METH...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/18-023-C
更新日期：2019-11-01 00:00:00
abstract：:A fundamental issue of restorative treatment is assessing the different conditions of cases not only from tooth-to-tooth but also from the activity of each caries lesion and the size of the cavity. In addition, restorative treatment is sometimes carried out for prosthetic and cosmetic purposes and involves cutting sou...
journal_title：Operative dentistry
pub_type：
doi：
更新日期：2002-05-01 00:00:00
abstract：CLINICAL RELEVANCE:When a resin nanoceramic inlay is cemented using self-adhesive cement, a universal dentin adhesive can be applied to the prepared cavity. The application of the adhesive before self-adhesive cement placement provides similar or better interfacial adaptation than without the adhesive. SUMMARY:Purpose...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-141-L
更新日期：2020-11-01 00:00:00
abstract：:This study evaluated the two-year clinical performance of two minimally invasive cavity preparation techniques, bur and laser, in Class I occlusal resin composite restorations. Twenty-seven patients, each having at least one pair of occlusal caries, were enrolled in this study. For each patient, one of the cavities wa...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/09-339-C
更新日期：2010-09-01 00:00:00
abstract：:This study evaluated in vitro the necessity of retention grooves in approximal boxes in class 2 preparations with faciolingually wide occlusal extensions (occlusal isthmus width 1.8 mm). Thirty-six class 2 mesio-occlusal cavities were prepared in sound human maxillary premolar teeth and divided into three groups of 12...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1993-03-01 00:00:00
abstract：OBJECTIVE::Computer aided design-computer aided machining (CAD-CAM) ceramic crowns are replacing ceramo-metal ones due to newly developed mechanical properties and esthetics. To obtain knowledge about their interactions due to polishing and occlusal contacts with the opposing dental enamel specimen, including surface r...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-153-L
更新日期：2019-01-01 00:00:00
abstract：OBJECTIVES:Whitening efficacy has been related to hydrogen peroxide (HP) diffusion into tooth structure. However, little information is available relating rheological properties to whitening efficacy. The purpose was to evaluate the whitening efficacy and HP penetration level of a 10% HP gel at three different viscosit...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/17-099-L
更新日期：2018-05-01 00:00:00
abstract：CLINICAL RELEVANCE:The degree of conversion of contemporary universal adhesives positively correlates with the bond strength to dentin. The correlation is more marked after thermocycling, suggesting that a high degree of conversion is required for long-term dentin bonding durability. SUMMARY:Purpose: The objectives of...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-165-L
更新日期：2020-09-01 00:00:00
abstract：:This study determined the relationship between marginal adaptation to dentin cavity preparations, tensile bond strength of the restorations, and mechanical properties of the composites. Contraction gaps, tensile bond strengths, flexural strengths, and Young's modulus of eight commercial resin composites were determine...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1999-11-01 00:00:00
abstract：:This study investigated the effect of two base materials with different elastic moduli (F2000 and Vitrebond) on the fracture load of machinable ceramic inlays. Standardized MOD cavities were prepared in 18 human maxillary first or second premolars. The teeth were randomly assigned to three groups of six premolars each...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/05-3
更新日期：2006-03-01 00:00:00
abstract：:The bulk-filling of deep, wide dental cavities is faster and easier than traditional incremental restoration. However, the extent of cure at the bottom of the restoration should be carefully examined in combination with the polymerization contraction and gap formation that occur during the restorative procedure. The a...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-324-L
更新日期：2015-03-01 00:00:00
abstract：:A core foundation system is frequently used in endodontically treated teeth that suffer excessive loss of the coronal portion of their structure. The volumetric shrinkage of core foundation resins may create marginal gaps that influence the bonding ability and longevity of a restored tooth. Little is known about how a...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2005-09-01 00:00:00
abstract：:The aim of this study was to evaluate the effect of grinding with diamond burs and low-temperature aging on the material surface characteristics and bacteria adhesion on a yttrium-stabilized tetragonal zirconia polycrystalline (Y-TZP) surface. Y-TZP specimens were made from presintered blocks, sintered as recommended ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-108-L
更新日期：2017-11-01 00:00:00
abstract：:This investigation examined the susceptibility to staining and translucency changes of some new tooth-colored restorative materials after immersion in different beverages. The materials studied were 3M Filtek Z350XT (ZT), 3M Filtek 350XT Flowable Restorative (ZF), Shofu Beautifil Flow Plus (BF), Shofu Beautifil II (B2...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/149027-L
更新日期：2015-03-01 00:00:00
abstract：:The present clinical case report describes the clinical steps of enamel microabrasion associated with dental bleaching to restore severely-pitted fluorosed teeth. The process of removing the fluorotic superficial stains started by using macroabrasion with a water-cooled fine tapered 3195 FF diamond bur. Rubber dam iso...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-116-T
更新日期：2019-11-01 00:00:00
abstract：:The available and proposed methods for determining the in vivo occlusal wear values of classes 1 and 2 restorations made of resinfilled composite materials are critically reviewed. A methodology to be used to address the fundamental question of the link between the wear of the in vivo restorations and the relevant mec...
journal_title：Operative dentistry
pub_type： 杂志文章,评审
doi：
更新日期：1991-03-01 00:00:00
abstract：:This study determined the degree of conversion of two LED (light-emitting diodes) (Elipar FreeLight [FL], 3M ESPE; GC e-Light [EL], GC), a high intensity (Elipar TriLight [TL], 3M ESPE) and a very high intensity (Astralis 10 [AS], Ivoclar Vivadent) halogen light. The degree of conversion of these lights was compared t...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-09-01 00:00:00
abstract：CLINICAL RELEVANCE:Computer-aided design/computer-aided manufacturing (CAD/CAM) composite resins are susceptible to degradation by dietary solvents. Dietary counselling is prudent when placing such CAD/CAM restorations. SUMMARY:This study determined the effect of dietary solvents on the surface roughness (Ra) of direc...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-070-L
更新日期：2020-07-01 00:00:00
abstract：:This in vitro study evaluated microleakage in Class II cavities restored with dental composite and varying light-curing units and the temperature of the composite when subjected to a thermocycling test. Ninety cavities were prepared on the proximal surfaces of bovine teeth and randomly divided according to the light-c...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/10-226-LR1
更新日期：2011-01-01 00:00:00
abstract：PURPOSE:To investigate the effect of different light exposure times, shades, and thicknesses on the depth of cure (DOC) of bulk fill composites. METHODS AND MATERIALS:Two bulk fill composites, Tetric EvoCeram Bulk Fill (TBF) and Sonic Fill (SF), and a conventional composite, Filtek Supreme Ultra (FSU), were evaluated....
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-057-L
更新日期：2017-09-01 00:00:00
abstract：OBJECTIVES:To evaluate the bond strength of adhesive luting agents applied to caries-affected dentin (CAD). METHODS:Thirty-six noncarious human third molars were abraded to expose an occlusal dentin surface. Caries lesions were induced in half of the samples using a microcosm biofilm model. Biofilm was cultivated unde...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/14-169-L
更新日期：2015-05-01 00:00:00
abstract：:Ceramic root-canal posts offer potential advantages over other types with respect to aesthetics and biocompatibility. Any post must be sufficiently rigid and retentive to withstand functional forces. Ceraposts (1.2 mm coronal diameter, ceramic, tapering, smooth posts) and Paraposts (1.25 mm, stainless-steel, parallel,...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-05-01 00:00:00
abstract：OBJECTIVES:Published transmission electron microscopy analysis of in vitro resin-dentin bonds shows that, after 44 months, almost 70% of collagen fibrils from the hybrid layer disappear. Matrix metalloproteinases (MMPs) play an important role in that process and are thought to be the main factor responsible for the sol...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/12-425-L
更新日期：2014-03-01 00:00:00
abstract：:This in vitro study investigated the correlation between factors related to cavosurface marginal adaptation and microleakage in Class II cavities restored with a light- or chemical-activated resin composite. Standardized cavities were prepared in 40 molars that were randomly divided between both materials. Each of the...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-16
更新日期：2007-01-01 00:00:00
abstract：:This study evaluated the biocompatibility of contemporary bulk-fill resin-based composites (RBCs) including PRG (pre-reacted glass ionomer) materials based on the International Organization for Standardization 10993. In addition, the effect of composite thickness on cytotoxicity was also assessed. Two standard composi...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-059-L
更新日期：2015-11-01 00:00:00
abstract：:This study determined the effect of bleaching agents on the fracture toughness of composite materials. Four nanofilled resin composites were evaluated: Filtek Supreme Plus, Tetric EvoCeram, Premise and Esthet-X. Four concentrations of bleaching agents were tested: Opalescence PF 10%, 20%, 35% and 45%. Fifty specimens ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/08-120-L
更新日期：2009-11-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate surface finish and gloss of a two-step composite finishing/polishing (F/P) disc system compared with two multistep systems on five composites. METHODS:Seventy-five disc-shaped composite specimens (D=10.0 mm, 2 mm thick, n=15 per composite) were made of microfill (Dur...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/10-162-L
更新日期：2011-03-01 00:00:00
abstract：:The purpose of this study was to compare the long-term survivals of two low-copper and three high-copper amalgam alloys, and to analyze four clinical factors for their possible effects on the restoration survivals. Some 1476 polished restorations were placed in hospital patients by a large number of operators and asse...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1991-09-01 00:00:00
abstract：:This study evaluated the pulp biocompatability of a new light-cured composite resin which was placed in etched glass-ionomer-lined cavities of monkey teeth. The pulpal response to this material was less than that to zinc-oxide eugenol cement in each observation period. Therefore this material seems to meet acceptable ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1991-07-01 00:00:00
abstract：:This study investigated the influence of different light sources associated with a transdental photoactivation technique on the marginal adaptation and hardness of composite restorations. Cavities (3 mm wide x 3 mm long x 1.5 mm in deep) were prepared on flattened bovine dentin and filled with Z250 composite (3M ESPE)...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/07-109
更新日期：2008-07-01 00:00:00
