Granule size control and targeting in pulsed spray fluid bed granulation.

Abstract:

:The primary aim of the study was to investigate the effects of pulsed liquid feed on granule size. The secondary aim was to increase knowledge of this technique in granule size targeting. Pulsed liquid feed refers to the pump changing between on- and off-positions in sequences, called duty cycles. One duty cycle consists of one on- and off-period. The study was performed with a laboratory-scale top-spray fluid bed granulator with duty cycle length and atomization pressure as studied variables. The liquid feed rate, amount and inlet air temperature were constant. The granules were small, indicating that the powder has only undergone ordered mixing, nucleation and early growth. The effect of atomizing pressure on granule size depends on inlet air relative humidity, with premature binder evaporation as a reason. The duty cycle length was of critical importance to the end product attributes, by defining the extent of intermittent drying and rewetting. By varying only the duty cycle length, it was possible to control granule nucleation and growth, with a wider granule size target range in increased relative humidity. The present study confirms that pulsed liquid feed in fluid bed granulation is a useful tool in end product particle size targeting.

journal_name

Int J Pharm

authors

Ehlers H,Liu A,Räikkönen H,Hatara J,Antikainen O,Airaksinen S,Heinämäki J,Lou H,Yliruusi J

doi

10.1016/j.ijpharm.2009.04.041

subject

Has Abstract

pub_date

2009-07-30 00:00:00

pages

9-15

issue

1-2

eissn

0378-5173

issn

1873-3476

pii

S0378-5173(09)00264-6

journal_volume

377

pub_type

杂志文章
  • Formulations and toxicologic in vivo studies of aqueous cyclosporin A eye drops with cyclodextrin nanoparticles.

    abstract::Cyclosporin A (CyA) is an immunosuppressive drug used topically to treat ocular inflammatory disorder such as dry eye disease (DES). It is a lipophilic cyclic peptide with molecular weight of 1202.6Da. The aim of this study was to develop surfactant free aqueous 0.2% (w/v) CyA eye drops where the drug is present in an...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.07.044

    authors: Jóhannsdóttir S,Kristinsson JK,Fülöp Z,Ásgrímsdóttir G,Stefánsson E,Loftsson T

    更新日期:2017-08-30 00:00:00

  • One-week in vivo sustained release of a peptide formulated into in situ forming implants.

    abstract::The LR12 peptide has been reported to reduce the size of infarct and improve both cardiac function and survival in myocardial infarction in murine models, after daily repeated intraperitoneal injections. In order to protect peptide from degrading and to prolong its release, in situ implants based on biocompatible biod...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.02.046

    authors: Parent M,Clarot I,Gibot S,Derive M,Maincent P,Leroy P,Boudier A

    更新日期:2017-04-15 00:00:00

  • β-Cyclodextrin encapsulation of nortriptyline HCl and amitriptyline HCl: Molecular insights from single-crystal X-ray diffraction and DFT calculation.

    abstract::The β-CD encapsulation of two tricyclic antidepressants (TCAs), nortriptyline (NRT) HCl and amitriptyline (AMT) HCl (most widely used TCA), has been thoroughly investigated by single-crystal X-ray diffraction and DFT calculation for insights into the inclusion complexation. X-ray analysis reveals that both drugs inser...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2019.118899

    authors: Aree T

    更新日期:2020-02-15 00:00:00

  • Microencapsulation of amorphous solid dispersions of fenretinide enhances drug solubility and release from PLGA in vitro and in vivo.

    abstract::The purpose of this study was to develop solid dispersions of fenretinide(4HPR), incorporate them into poly(lactic-co-glycolic)(PLGA) millicylindrical implants, and evaluate the resulting implants in vitro and in vivo for future applications in oral cancer chemoprevention. Due to the extreme hydrophobicity of 4HPR, 4H...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2020.119475

    authors: Nieto K,Mallery SR,Schwendeman SP

    更新日期:2020-08-30 00:00:00

  • Polymer particle erosion controlling drug release. I. Factors influencing drug release and characterization of the release mechanism.

    abstract::The present study deals with controlled drug delivery from hydrocolloid tablets by polymer particle erosion. The influence of excipients and formulation factors on the dissolution behaviour of the methyl hydroxyethyl cellulose (MHEC)-tablets is investigated. Linear drug release with low susceptibility to hydrodynamic ...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(01)00596-8

    authors: Zuleger S,Lippold BC

    更新日期:2001-04-17 00:00:00

  • A 4-strain probiotic supplement influences gut microbiota composition and gut wall function in patients with ulcerative colitis.

    abstract::Symprove, a multi-strain probiotic, has been shown to exert a mild anti-inflammatory effect in patients with ulcerative colitis (UC). We examined stool samples from 3 patients with UC in order to create microbiotas in an in-vitro gut model. The effects of Symprove on bacterial diversity and metabolic activity in the m...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2020.119648

    authors: Ghyselinck J,Verstrepen L,Moens F,Van den Abbeele P,Said J,Smith B,Bjarnason I,Basit AW,Gaisford S

    更新日期:2020-09-25 00:00:00

  • Application of continuous twin screw granulation for the metformin hydrochloride extended release formulation.

    abstract::This study focuses on evaluating the potential of transferring from a batch process to continuous process for manufacturing of the extended release formulation. Metformin hydrochloride (HCl) was used in the model formulation which was intended to contain the high amount of hydrophilic drug. The effects of barrel tempe...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.07.019

    authors: Kim SH,Hwang KM,Cho CH,Nguyen TT,Seok SH,Hwang KM,Kim JY,Park CW,Rhee YS,Park ES

    更新日期:2017-08-30 00:00:00

  • Evaluation of childhood exposure to di(2-ethylhexyl) phthalate from perfusion kits during long-term parenteral nutrition.

    abstract::Leachability of the plasticizer di(2-ethylhexyl) phthalate (DEHP) from administration sets into intravenous parenteral emulsions containing fat was investigated. DEHP is added to polyvinyl chloride (PVC) to impart flexibility. However, DEHP is a lipid-soluble suspected carcinogen that is hepatotoxic and teratogenic in...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(03)00335-1

    authors: Kambia K,Dine T,Gressier B,Bah S,Germe AF,Luyckx M,Brunet C,Michaud L,Gottrand F

    更新日期:2003-08-27 00:00:00

  • Preparation of nimodipine-loaded microemulsion for intranasal delivery and evaluation on the targeting efficiency to the brain.

    abstract::The purpose of this study was to improve the solubility and enhance the brain uptake of nimodipine (NM) in an o/w microemulsion, which was suitable for intranasal delivery. Three microemulsion systems stabilized by the nonionic surfactants either Cremophor RH 40 or Labrasol, and containing a variety of oils, namely is...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2004.01.039

    authors: Zhang Q,Jiang X,Jiang W,Lu W,Su L,Shi Z

    更新日期:2004-05-04 00:00:00

  • Tableting process optimisation with the application of fuzzy models.

    abstract::A quality-by-design (QbD) principle, including process analytical technology, is becoming the principal idea in drug development and manufacturing. The implementation of QbD into product development and manufacturing requires larger resources, both human and financial, however, large-scale production can be establishe...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2010.01.023

    authors: Belic A,Skrjanc I,Bozic DZ,Vrecer F

    更新日期:2010-04-15 00:00:00

  • Behaviour of silver nanoparticles in simulated saliva and gastrointestinal fluids.

    abstract::Continuously increasing application of silver nanoparticles (AgNPs) requires information on their safety and performance under biological conditions. Assessment of AgNPs in biological systems is also related to availability of robust toxicological methods for evaluation of toxic potential of AgNPs and information on t...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.05.026

    authors: Pinďáková L,Kašpárková V,Kejlová K,Dvořáková M,Krsek D,Jírová D,Kašparová L

    更新日期:2017-07-15 00:00:00

  • Role of the elasticity of pharmaceutical materials on the interfacial mechanical strength of bilayer tablets.

    abstract::The effect of the elasticity of various pharmaceutical materials on the interfacial adhesion in bilayer tablets was investigated. The elastic properties of five pharmaceutical products were characterized by their total elastic recovery. To test the interfacial strength of the bilayer tablets a new flexural test was pr...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2013.09.009

    authors: Busignies V,Mazel V,Diarra H,Tchoreloff P

    更新日期:2013-11-30 00:00:00

  • Optimisation of glutathione conjugation to liposomes quantified with a validated HPLC assay.

    abstract::Glutathione (GSH) grafted onto nanoliposomes (GSH-liposomes) have the potential to enhance drug delivery into the brain. GSH is known to be an unstable tripeptide, however, despite widespread use to promote active transport its stability has been largely ignored to date. Therefore this study focuses on the optimisatio...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2019.118451

    authors: Reginald-Opara JN,Svirskis D,O'Carroll SJ,Sreebhavan S,Dean JM,Wu Z

    更新日期:2019-08-15 00:00:00

  • Incorporation of a model protein into chitosan-bile salt microparticles.

    abstract::In order to develop a mucosal delivery system based on biocompatible polymers, a new methodology for production of protein-loaded microparticles is developed. Chitosan anionic precipitation/coacervation is accomplished by the addition of sodium deoxycholate (DCA). These microparticles were prepared under mild conditio...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2006.01.006

    authors: Lameiro MH,Lopes A,Martins LO,Alves PM,Melo E

    更新日期:2006-04-07 00:00:00

  • Antibacterial activity of triclosan chitosan coated graft on hernia graft infection model.

    abstract::The use of mesh in hernia repair has become common, because of lower recurrence rate and simple application. Data from the meta-analysis and the multi-central studies support the use of meshes in hernia repair. One of the complications due to the hernia repair with mesh is the infection. The incidence range is between...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2009.05.059

    authors: Cakmak A,Cirpanli Y,Bilensoy E,Yorganci K,Caliş S,Saribaş Z,Kaynaroğlu V

    更新日期:2009-11-03 00:00:00

  • Effect of structural factors on release profiles of camptothecin from block copolymer conjugates with high load of drug.

    abstract::The aim of the present work was the synthesis and study the kinetics and profiles of camptothecin (CPT) release form block co- and ter-polymer conjugates comprising polylactide (PLA) segments and CPT moieties, structurally diverse by degrees of branching, content of d-PLA units and poly(ethylene glycol) methyl ether m...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2018.01.022

    authors: Plichta A,Kowalczyk S,Olędzka E,Sobczak M,Strawski M

    更新日期:2018-03-01 00:00:00

  • A single-layer film coating for colon-targeted oral delivery.

    abstract::Most pH-sensitive polymer coating studies for potential colonic delivery systems apply multiple layers to protect the active agent from degradation and early release in the stomach and small intestine. This study designed a single-coat pH-sensitive layer for colon-specific delivery with a potential biopolymer, namely,...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2019.01.066

    authors: Nguyen MNU,Tran PHL,Tran TTD

    更新日期:2019-03-25 00:00:00

  • Effect of alkylcarbonates of gamma-cyclodextrins with different chain lengths on drug complexation and release characteristics.

    abstract::Alkylcarbonates of gamma-cyclodextrins were produced and their inclusion complexes with four poorly water-soluble drugs of different structures and solubilities were prepared. The alkylcarbonates and the alkylcarbonate drug complexes were characterized by DSC and XRPD; the physical mixtures were used as control. Solub...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2007.03.001

    authors: Cavalli R,Trotta F,Trotta M,Pastero L,Aquilano D

    更新日期:2007-07-18 00:00:00

  • Physicochemical properties of tamoxifen hemicitrate sesquihydrate.

    abstract::A novel modification of tamoxifen [(Z)-2-[4-(1,2-diphenyl-1-butenyl) phenoxy]-N,N-dimethylethylamine] citrate, tamoxifen hemicitrate hydrate was prepared. The crystalline form was identified and characterized by powder and single crystal X-ray diffractometries, differential scanning calorimetry (DSC), thermal gravimet...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2007.10.021

    authors: Kojima T,Katoh F,Matsuda Y,Teraoka R,Kitagawa S

    更新日期:2008-03-20 00:00:00

  • Arsenic release from glass containers by action of intravenous nutrition formulation constituents.

    abstract::Pharmacopoeias prescribe tests to determine the levels of arsenic in raw materials and glass containers. In this study, glass ampoules for injectables containing individually the main components of intravenous nutrition formulations were submitted to the hydrolytic resistance test by heating at 121 degrees C for 30 mi...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2006.02.008

    authors: Bohrer D,Becker E,Nascimento PC,Mörschbächer V,de Carvalho LM,da Silva Marques M

    更新日期:2006-06-06 00:00:00

  • The application of STEP-technology® for particle and protein dispersion detection studies in biopharmaceutical research.

    abstract::Particle detection and analysis techniques are essential in biopharmaceutical industries to evaluate the quality of various parenteral formulations regarding product safety, product quality and to meet the regulations set by the authority agencies. Several particle analysis systems are available on the market, but for...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2018.03.050

    authors: Gross-Rother J,Herrmann N,Blech M,Pinnapireddy SR,Garidel P,Bakowsky U

    更新日期:2018-05-30 00:00:00

  • Buccal adhesive films with moisturizer- the next level for dry mouth syndrome?

    abstract::This study was undertaken to prepare films by solvent evaporation method comprising well-known polymers in order to investigate their potential for buccal suitability. Mucoadhesive films were manufactured using different polymers such as ethyl cellulose, hydroxyethyl cellulose, hydroxypropyl methylcellulose as well as...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2018.08.032

    authors: Laffleur F,Krouská J,Tkacz J,Pekař M,Aghai F,Netsomboon K

    更新日期:2018-10-25 00:00:00

  • Development of enteric-coated fixed dose combinations of amorphous solid dispersions of ezetimibe and lovastatin: Investigation of formulation and process parameters.

    abstract::Enteric-coated fixed-dose combinations of ezetimibe and lovastatin were prepared by fluid bed coating aiming to avoid the acidic conversion of lovastatin to its hydroxyacid derivative. In a two-step process, sucrose beads were layered with a glass solution of ezetimibe, lovastatin and Soluplus®, top-coated with an ent...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.01.053

    authors: Riekes MK,Dereymaker A,Berben P,Augustijns P,Stulzer HK,Van den Mooter G

    更新日期:2017-03-30 00:00:00

  • Mucoadhesivity and release properties of quaternary ammonium-chitosan conjugates and their nanoparticulate supramolecular aggregates: an NMR investigation.

    abstract::Selective relaxation rate measurements effectively proved the affinity of dexamethasone 21-phosphate disodium salt for quaternary ammonium-chitosan conjugates, their thiolated derivatives and the corresponding nanostructured aggregates. Affinity was also probed by dynamic dialysis. The release profile of dexamethasone...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2013.12.018

    authors: Uccello-Barretta G,Balzano F,Aiello F,Senatore A,Fabiano A,Zambito Y

    更新日期:2014-01-30 00:00:00

  • Investigation of properties and recrystallisation behaviour of amorphous indomethacin samples prepared by different methods.

    abstract::The aim of this study was to investigate if amorphous indomethacin samples, prepared using different preparation methods, exhibit different structural and kinetic characteristics and if these differences can be correlated to their physical stability (time to crystallisation). Samples were prepared by melt quenching, s...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2010.12.019

    authors: Karmwar P,Graeser K,Gordon KC,Strachan CJ,Rades T

    更新日期:2011-09-30 00:00:00

  • The use of MTDSC to assess the amorphous phase content of a micronized drug substance.

    abstract::Mechanical treatments such as grinding, milling or micronization applied to crystalline drug substances may induce changes such as the occurrence of crystal defects and/or amorphous regions. These changes are likely to affect the chemical and physical properties of the material as well as the corresponding drug produc...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(99)00273-2

    authors: Guinot S,Leveiller F

    更新日期:1999-12-01 00:00:00

  • 3D printed orodispersible films with Aripiprazole.

    abstract::Three dimensional printing technology is gaining in importance because of its increasing availability and wide applications. One of the three dimensional printing techniques is Fused Deposition Modelling (FDM) which works on the basis of hot melt extrusion-well known in the pharmaceutical technology. Combination of fu...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2017.05.052

    authors: Jamróz W,Kurek M,Łyszczarz E,Szafraniec J,Knapik-Kowalczuk J,Syrek K,Paluch M,Jachowicz R

    更新日期:2017-11-30 00:00:00

  • Enhancing effect of surfactants on fexofenadine.HCl transport across the human nasal epithelial cell monolayer.

    abstract::The effect of various surfactants (sodium cholate, sodium taurocholate, Tween 80 and Poloxamer F68) on enhancing the transepithelial permeability of fexofenadine.HCl was evaluated in a human nasal epithelial cell monolayer model. The cytotoxicity of the surfactants on the human nasal epithelial cells was evaluated by ...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2006.08.043

    authors: Lin H,Gebhardt M,Bian S,Kwon KA,Shim CK,Chung SJ,Kim DD

    更新日期:2007-02-07 00:00:00

  • α-Glucosyl hesperidin induced an improvement in the bioavailability of pranlukast hemihydrate using high-pressure homogenization.

    abstract::The α-glucosyl hesperidin (Hsp-G)-induced improvement of both the dissolution and absorption properties of pranlukast hemihydrate (PLH) was achieved by means of a high-pressure homogenization (HPH) processing. The average particle size in the HPH-processed suspension was decreased significantly after 50 cycles of proc...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2011.03.017

    authors: Uchiyama H,Tozuka Y,Asamoto F,Takeuchi H

    更新日期:2011-05-30 00:00:00

  • Effects of citicholine and dimethylsulfoxide on transepithelial transport of passively diffused drugs in the Caco-2 cell culture model.

    abstract::The objective of this study was to determine, using a Caco-2 cell monolayer model, the extent to which the paracellular and transcellular routes are altered by citicholine (CDP-Ch) and DMSO in the presence of human serum albumin (HSA). The apparent permeability (Papp) of mannitol in the presence of 4% (w/v) HSA was in...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(02)00588-4

    authors: Demirbas S,Stavchansky S

    更新日期:2003-01-30 00:00:00