Abstract：
:This study compared the amount of artificial plaque synthesized in vitro by Streptococcus sobrinus on various dental materials using radioisotopes. In particular, plaque-retaining capacities of new types of ceramics were the focus of this study. Specimens were fabricated from the following materials (one amalgam alloy [Spherical-D], one casting gold alloy [Casting Gold TYPE I], one resin composite [Herculite XR] and three ceramics [Vita Celay Blanks, IPS Empress and Dicor MGC]). The amount of bacteria and glucans adhered on the specimens was measured after incubation for 24 hours at 37 degrees C with radio-labeled cariogenic bacteria and sucrose. This adhesion test was performed using two different surfaces with 600-grit roughness and clinical smoothness. Irrespective of the surface roughness, the least amount of plaque adhered to the ceramics. However, in the case of the resin composite and amalgam, the amount of bacteria and glucan adhesion decreased dramatically by polishing, though there were no statistically different changes in the amount of bacteria and glucans that adhered to the ceramics even after polishing. In general, the amount of adhered bacteria showed almost the same tendency as that of glucans. Although no statistical differences in the amount of bacteria and glucan adhesion were detected among the three ceramics investigated in this study, a lesser amount of bacteria and glucans adhered to them compared to the other materials.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Kawai K,Urano Mkeywords:
subject
Has Abstractpub_date
2001-07-01 00:00:00pages
396-400issue
4eissn
0361-7734issn
1559-2863journal_volume
26pub_type
杂志文章abstract：OBJECTIVES::The use of high-viscosity glass-ionomer cements (HVGICs) for atraumatic restorative treatment (ART) restorations is widely practiced with the advent of various HVGICs. However, the bonding of the latter to caries-affected dentin (CAD) should be validated, especially because it is the common substrate left a...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-154-L
更新日期：2018-11-01 00:00:00
abstract：:This study compared the degree of marginal leakage of a compomer in Class V cavities of human primary molars prepared by a conventional dental bur and air abrasion with or without acid etching. Fifty-six non-carious extracted primary molars were randomly divided into four groups (n=14) to be prepared by four technique...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-03-01 00:00:00
abstract：:A technique of restoring Class II posterior restorations with resin-based composite and a pre-polymerized composite insert was presented. This technique is intended to aid the practitioner in obtaining tight, broad, proximal contacts without having to purchase special instruments or materials. This method is not time-...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-07-01 00:00:00
abstract：:This study examined the relationship between the bond agent application duration and the dentin bond strength of several single-application bonding systems. The restorative material/ bonding systems used were Reactmer, with its single-application bonding system Reactmer Bond (RB, Shofu Inc, Kyoto, Japan); Palfique Est...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2002-05-01 00:00:00
abstract：:One hundred cervical caries-free, nonundercut lesions were restored in 13 patients of mean age 60.5 years, using Silux Plus or Estio LC resin composite bonded with Fuji Bond LC. Patients were recalled at 6 months and 1 year. A 1-year cumulative retention rate of 98% was recorded, while marginal staining was absent. ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1998-11-01 00:00:00
abstract：:This study assessed the in vitro influence of surface sealing on the surface roughness of a posterior resin composite before and after toothbrushing. Thirty specimens (13 mm diameter x 1 mm high) were fabricated from Filtek-P60 resin composite and randomly assigned to three groups (n = 10): a non-sealed control and tw...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2003-05-01 00:00:00
abstract：CLINICAL RELEVANCE:When a resin nanoceramic inlay is cemented using self-adhesive cement, a universal dentin adhesive can be applied to the prepared cavity. The application of the adhesive before self-adhesive cement placement provides similar or better interfacial adaptation than without the adhesive. SUMMARY:Purpose...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-141-L
更新日期：2020-11-01 00:00:00
abstract：:This in-vitro study compared the resistance of extensive amalgam restorations retained by either four Regular TMS Link Plus pins, four amalgapins, Amalgambond Plus, Amalgambond Plus with HPA, Scotchbond Multi-Purpose Plus, PQ Amalgam, Panavia F 2.0, All-Bond 2 or Resinomer. Ninety caries-free third molars were embedde...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/08-5
更新日期：2008-11-01 00:00:00
abstract：:No data are available on the direct acute vascular effect of dental bonding materials on the dental pulp. This study investigated the effects of the components of a composite resin-bonding system on pulpal vascular diameter. Three groups of 10 male Sprague-Dawley rats (weighing 330 +/- 51 g) were used for this investi...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-09-01 00:00:00
abstract：PURPOSE:This study evaluated the effect of thermocycling on the microtensile bond strength of four adhesive luting agents to GN-I CAD-CAM ceramic. The hypothesis tested was that thermocycling did not affect bonding effectiveness, irrespective of the luting agents used. MATERIALS AND METHODS:Ceramic specimens of two di...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/06-106
更新日期：2007-07-01 00:00:00
abstract：:Amalgam has been used in the restoration of structurally compromised posterior teeth for many years. When placing large amalgam restorations, replacement of weak cusps with restorative material is recommended to prevent tooth fracture. This recommendation can be modified with new guidelines using modern adhesive techn...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-082-T
更新日期：2012-07-01 00:00:00
abstract：:This study investigated the influence of curing lights and modes on the cross-link density of dental composites. Four LED/halogen curing lights (LED-Elipar Freelight [FL], 3M-ESPE and GC e-light [EL], GC; high intensity halogen-Elipar Trilight [TL], 3M-ESPE; very high intensity halogen-Astralis 10 [AS], Ivoclar Vivade...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-07-01 00:00:00
abstract：:This study evaluated the regional tensile bond strength of a dual-cure resin composite core material to root canal dentin using photo and dual-cure adhesives and different modes of polymerization. Nineteen extracted premolars were decoronated and their root canals prepared to a depth of 8 mm and a width of 1.4 mm usin...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-09-01 00:00:00
abstract：OBJECTIVES::To evaluate the effect of a remineralizing gel combining fluoride and calcium silicate/phosphate or a sodium fluoride gel on bleached enamel microhardness, color, and wear susceptibility. METHODS AND MATERIALS::Two hundred forty bovine enamel-dentin samples were prepared. Baseline analysis of Knoop microha...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-150-L
更新日期：2019-01-01 00:00:00
abstract：:Recently, manufacturers introduced presterilized, single-use, plastic light-curing tips to be used either routinely or on patients with known or questionable communicable health concerns. The purpose of this study was to examine the effect of these single-use tips on light transmission compared to conventional fiber-o...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1998-07-01 00:00:00
abstract：:This case report illustrates how to restore severely compromised teeth with direct composite restorations. The size of the restorations presented is often considered by dentists as being a contraindication for direct composites. Hence, the technique is explained step by step, addressing the crucial points. ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-001-T
更新日期：2016-09-01 00:00:00
abstract：:Although rare, subcutaneous air emphysema can occur during dental procedures such as endodontic treatment, surgical extractions, and preparing a tooth for an indirect or direct dental restoration. We report the development of a subcutaneous air emphysema that was introduced through the periodontal ligament of an untre...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-155-S
更新日期：2017-09-01 00:00:00
abstract：OBJECTIVES:This study investigated the influence of resin composite preheating temperature, light curing regimen (mode and duration) on post-gel shrinkage strain (PGSS) and degree of conversion (DC) of a restorative resin composite. METHODS:A hybrid resin composite preheated to three different temperatures (37 degrees...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/09-072-L
更新日期：2010-03-01 00:00:00
abstract：:Ceramic root-canal posts offer potential advantages over other types with respect to aesthetics and biocompatibility. Any post must be sufficiently rigid and retentive to withstand functional forces. Ceraposts (1.2 mm coronal diameter, ceramic, tapering, smooth posts) and Paraposts (1.25 mm, stainless-steel, parallel,...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-05-01 00:00:00
abstract：:This study evaluated the shear-bond strength of 11 luting cements from different material classes to manufactured pre-treated zirconia ceramics (Lava: 97% ZrO2, stabilized with 3% Y2O3). In addition, the influence of the curing method on shear-bond strength was investigated. The cements examined were one zinc-phosphat...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2005-05-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate surface finish and gloss of a two-step composite finishing/polishing (F/P) disc system compared with two multistep systems on five composites. METHODS:Seventy-five disc-shaped composite specimens (D=10.0 mm, 2 mm thick, n=15 per composite) were made of microfill (Dur...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/10-162-L
更新日期：2011-03-01 00:00:00
abstract：:Amalgapins are susceptible to early fracture during matrix removal and carving. The purpose of this study was to examine the early fracture resistance of amalgapin-retained restorations using a spherical amalgam alloy, an admixed amalgam alloy, a combination of admixed alloy over the spherical alloy, and a recently in...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1998-03-01 00:00:00
abstract：:Under clinical conditions, the time needed for the proper light curing of luting composites or the multi-incremental buildup of a large restoration with halogen curing units is quite extensive. Due to the development of high power curing devices, such as argon lasers and plasma arc lights and, in order to decrease cur...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/06-79
更新日期：2007-05-01 00:00:00
abstract：:This study evaluated the effect of polishing after one-day storage in water on the gap formation around a Class V restoration completely bordered by enamel (coronal cavity) using one resin-modified glass ionomer, one compomer and one conventional glass ionomer as a control. The study also examined gap formation of the...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2002-01-01 00:00:00
abstract：:The purpose of this study was to develop an accurate and reproducible intraoral method of measuring the distance between two teeth, and to conduct a clinical pilot study of the effect of placement of a class 2 posterior resin restoration upon this intertooth dimension. A Kaman Sciences KD-2611 noncontact displacement ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1989-10-01 00:00:00
abstract：:This review compares nine published studies conducted at the Indiana University School of Dentistry. Twenty-five products in four different systems were evaluated using the Trubyte Bioform Color Ordered Shade Guide and a Chroma Meter. The dentist-prescribed overnight bleaching delta mean shade guide value (DSGV) 10 we...
journal_title：Operative dentistry
pub_type： 杂志文章,评审
doi：10.2341/08-74
更新日期：2009-03-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate the effect of phosphoric acid pre-etching times on shear bond strength (SBS) and surface free energy (SFE) with single-step self-etch adhesives. METHODS:The three single-step self-etch adhesives used were: 1) Scotchbond Universal Adhesive (3M ESPE), 2) Clearfil tri-S...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-221-L
更新日期：2016-07-01 00:00:00
abstract：:A study was conducted to compare the shear bond strength of a glass-ionomer cement and glass-ionomer base to coronal and radicular dentin. Two different glass ionomers were bonded to paired coronal and radicular human dentin surfaces that had received no surface treatment or had been treated passively for 20 seconds w...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-07-01 00:00:00
abstract：:The effect of interdental separation of a special separation ring and wooden wedge was investigated. In a split-mouth design, 27 patients were randomly assigned to one of two groups (W or S). In 11 patients, an interdental wooden wedge (Hawe-Neos) was placed (group W), and in 16 patients, a separation ring (Composi-Ti...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-73
更新日期：2007-05-01 00:00:00
abstract：:The DIAGNOdent, a device used in caries detection, uses a laser to excite fluorescence from pigments in carious tooth structure. In clinical use assessing occlusal surfaces, distance and tooth structure may separate the instrument's tip from the fluorescent source.The aim of this in vitro study was to examine the effe...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/10-179-L
更新日期：2012-03-01 00:00:00
