Transient displacement induced in shear wave elastography: comparison between analytical results and ultrasound measurements.

Abstract:

:It is now accepted that an effective way to investigate the elastic properties of soft tissues is to generate a localized transient acoustic radiation force and to follow the associated displacements in the time/space domain. Shear waves induced by this stress field are particularly interesting in this kind of medium because they are governed by the shear elastic modulus mu, which is directly linked to the Young modulus, and spatial distribution and temporal evolution of the transient motion induced must therefore be obtained in detail. We report here a model based on the elastodynamic Green's function formalism to describe these displacements. 3D simulation of radiation force in homogenous elastic media was performed and the displacement curves computed at different radial distances for different temporal force profiles. Amplitude and duration of displacement were found to be reliable parameters to characterize the elastic properties of the medium. Experimental measurements were performed in a homogeneous agar-gelatin tissue-mimicking phantom, and two transducers were used to generate the radiation force and follow the induced displacements. Displacements obtained from different lateral locations around the applied force axis were then used to reconstruct the shear-wave propagation in a scan plane as a function of time. The experimental displacements/curves agreed with the theoretical profiles obtained by the elastodynamic Green's function formalism.

journal_name

Ultrasonics

journal_title

Ultrasonics

authors

Elkateb Hachemi M,Callé S,Remenieras JP

doi

10.1016/j.ultras.2006.06.022

subject

Has Abstract

pub_date

2006-12-22 00:00:00

pages

e221-5

eissn

0041-624X

issn

1874-9968

pii

S0041-624X(06)00275-7

journal_volume

44 Suppl 1

pub_type

杂志文章
  • Experimental and numerical investigations of mechanical displacements in surface acoustic wave bounded beams.

    abstract::The present paper studies experimentally and numerically the surface acoustic wave (SAW) field on a piezoelectric substrate generated by interdigital transducers (IDT). On the one hand, mechanical displacements produced by the SAW are measured with the help of a laser Doppler vibrometer. On the other hand, mechanical ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106077

    authors: Weser R,Darinskii AN,Weihnacht M,Schmidt H

    更新日期:2020-08-01 00:00:00

  • Development of an ultra-portable echo device connected to USB port.

    abstract::In practical cardiology, a stethoscope based auscultation has been used to reveal the patient's clinical status. Recently, several hand-held echo devices are going on market and they are expected to play a role as "visible" auscultation instead of stethoscope. We have developed a portable and inexpensive echo device w...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2003.11.009

    authors: Saijo Y,Nitta S,Kobayashi K,Arai H,Nemoto Y

    更新日期:2004-04-01 00:00:00

  • Phonophoresis: an in vivo evaluation using three topical anaesthetic preparations.

    abstract::An electrical sensory perception threshold technique has been developed for use with human volunteers. This technique has been used to reproducibly quantify the effects of three different commercially available topical anaesthetic preparations on superficial sensory cells (nociceptors) in the skin. Low intensities (0....

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(90)90075-y

    authors: Williams AR

    更新日期:1990-05-01 00:00:00

  • Bolt axial stress measurement based on a mode-converted ultrasound method using an electromagnetic acoustic transducer.

    abstract::A method is proposed to measure the stress on a tightened bolt using an electromagnetic acoustic transducer (EMAT). A shear wave is generated by the EMAT, and a longitudinal wave is obtained from the reflection of the shear wave due to the mode conversion. The ray paths of the longitudinal and the shear wave are analy...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.11.003

    authors: Ding X,Wu X,Wang Y

    更新日期:2014-03-01 00:00:00

  • Semiconductor superlattices: a tool for terahertz acoustics.

    abstract::The properties of optical to acoustic transduction of semiconductor superlattices have been explored for several years in the sub terahertz frequency range. Using femtosecond laser pulses focused on these structures, acoustic modes are excited with a frequency related to the periodicity of the structure stacking. We h...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.07.009

    authors: Huynh A,Perrin B,Lemaître A

    更新日期:2015-02-01 00:00:00

  • A new analytic expression for fast calculation of the transient near and far field of a rectangular baffled piston.

    abstract::Essential to (cardiac) 3D ultrasound are 2D matrix array transducer technology and the associated (two-stage) beam forming. Given the large number of degrees of freedom and the complexity of this problem, simulation tools play an important role. Hereto, the impulse response (IR) method is commonly used. Unfortunately,...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.12.014

    authors: Ortega A,Tong L,D'hooge J

    更新日期:2014-04-01 00:00:00

  • Numerical and experimental analysis of strongly nonlinear standing acoustic waves in axisymmetric cavities.

    abstract::In this paper the behaviour of strongly nonlinear waves in axisymmetric resonators is experimentally and numerically studied. Experiments are carried out in a cylindrical cavity, which transversal dimension is bigger than the longitudinal one, excited by a narrow band transducer. The quality factor and displacement am...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2005.02.001

    authors: Vanhille C,Campos-Pozuelo C

    更新日期:2005-08-01 00:00:00

  • Methods for reducing cutting temperature in ultrasonic cutting of bone.

    abstract::Ultrasonic cutting is widely used in food processing applications to produce a clean and accurate cut. However, it is yet to be adopted as an instrument of choice in orthopaedic applications, mainly due to the high temperatures that can be generated at the cut site and the consequent requirement to use additional cool...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.06.046

    authors: Cardoni A,MacBeath A,Lucas M

    更新日期:2006-12-22 00:00:00

  • Solder joint failure localization of welded joint based on acoustic emission beamforming.

    abstract::A localization approach of welded joint damage is proposed based on acoustic emission (AE) beamforming. In this method, a uniform line array is introduced to detect the AE signal of welded joints in specified area. In order to investigate the influence of fillet and crimping commonly existing in a welded plate structu...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.11.002

    authors: Liu X,Xiao D,Shan Y,Pan Q,He T,Gao Y

    更新日期:2017-02-01 00:00:00

  • Influence of nesting shell size on brightness longevity and resistance to ultrasound-induced dissolution during enhanced B-mode contrast imaging.

    abstract::This study aims to bridge the gap between transport mechanisms of an improved ultrasound contrast agent (UCA) and its resulting behavior in a clinical imaging study. Phospholipid-shelled microbubbles nested within the aqueous core of a polymer microcapsule are examined for their use and feasibility as an improved UCA....

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.06.019

    authors: Wallace N,Dicker S,Lewin P,Wrenn SP

    更新日期:2014-12-01 00:00:00

  • Modal analysis and moving performance of a single-mode linear ultrasonic motor.

    abstract::A single-mode linear ultrasonic motor was developed in this study. On the stator, a group of four pieces of piezoelectric ceramics PZT8 were utilized to generate the ultrasonic vibration. A specially designed modal conversion horn with an oblique beam was applied to transfer the longitudinal vibration to an additional...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106216

    authors: Yin Z,Dai C,Cao Z,Li W,Chen Z,Li C

    更新日期:2020-12-01 00:00:00

  • Optimization of electrode size for aluminum-nitride matrix ultrasonic transducers in the frequency range above 200 MHz.

    abstract::This paper describes an optimization method of the top electrode size for a thin film matrix ultrasonic transducer (M-UT) in the frequency range above 200 MHz. The goal of this work is to design an optimal top electrode size for an M-UT providing the maximal output peak-peak voltage (V(PP)) and the maximal signal-to-n...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2012.10.018

    authors: Wei Y,Herzog T,Heuer H

    更新日期:2013-03-01 00:00:00

  • Perspectives in clinical uses of high-intensity focused ultrasound.

    abstract::Focused ultrasound holds promise in a large number of therapeutic applications. It has long been known that high intensity focused ultrasound can kill tissue through coagulative necrosis. However, it is only in recent years that practical clinical applications are becoming possible, with the development of high power ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.04.003

    authors: Clement GT

    更新日期:2004-08-01 00:00:00

  • Peculiarities of energy trapping of the UHF elastic waves in diamond-based piezoelectric layered structure. II. Lateral energy flow.

    abstract::Features of an acoustic energy trapping and outflow in a High-overtone Bulk Acoustic Resonator (HBAR) were considered. On the example of a specified resonator based on a piezoelectric layered structure (PLS) as "Al/AlN/Mo/(100) diamond", the simulation of the propagation of microwave acoustic waves in the range of 10-...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106311

    authors: Kvashnin GM,Sorokin BP

    更新日期:2021-03-01 00:00:00

  • Detecting broken-wire flaws at multiple locations in the same wire of prestressing strands using guided waves.

    abstract::Broken wires often occur at multiple locations in the same wire of a strand due to the recovery length, which is defined as the length of the wire taking up its full share of the axial load from the break point. The detection of broken-wire flaws at multiple locations along the same wire is investigated using guided w...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2012.05.003

    authors: Xu J,Wu X,Sun P

    更新日期:2013-01-01 00:00:00

  • Multidimensional spectral analysis of the ultrasonic radiofrequency signal for characterization of media.

    abstract::The importance of the analysis of the radiofrequency signal is by now recognized in the field of tissue characterization via ultrasound. The RF signal contains a wealth of information and structural details that are usually lost in the B-Mode representation. The HyperSPACE (Hyper SPectral Analysis for Characterization...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.02.010

    authors: Granchi S,Vannacci E,Biagi E,Masotti L

    更新日期:2016-05-01 00:00:00

  • A fast technique for hyper-echoic region separation from brain ultrasound images using patch based thresholding and cubic B-spline based contour smoothing.

    abstract::Ultrasound image guided brain surgery (UGBS) requires an automatic and fast image segmentation method. The level-set and active contour based algorithms have been found to be useful for obtaining topology-independent boundaries between different image regions. But slow convergence limits their use in online US image s...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2020.106304

    authors: Chel H,Bora PK,Ramchiary KK

    更新日期:2021-03-01 00:00:00

  • A new optical method for the detection of in-plane motion of ultrasound propagating in metals.

    abstract::This paper describes a laser optical technique for the detection of in-plane (IP) motion of ultrasonic waves propagating in solids. This interference-based laser optical technique includes a tiny square indentation with a width of about 30 microm on the sample surface and a relatively simple optical arrangement. The c...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.076

    authors: Yang CH,Tsai YC

    更新日期:2006-12-22 00:00:00

  • Stiffness evaluation of contacting surfaces by bulk and interface waves.

    abstract::This paper describes ultrasonic measurements of normal and tangential stiffnesses of the contacting interface between polished aluminum blocks subjected to nominal contact pressures up to about 3.8 MPa. These stiffnesses were evaluated by ultrasonic spectroscopy methods for the bulk (longitudinal and transverse) wave ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2007.08.005

    authors: Biwa S,Hiraiwa S,Matsumoto E

    更新日期:2007-12-01 00:00:00

  • Influence of electrical boundary conditions on profiles of acoustic field and electric potential of shear-horizontal acoustic waves in potassium niobate plates.

    abstract::The profiles of an acoustic field and electric potential of the forward and backward shear-horizontal (SH) acoustic waves of a higher order propagating in X-Y potassium niobate plate have been theoretically investigated. It has been shown that by changing electrical boundary conditions on a surface of piezoelectric pl...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2018.01.010

    authors: Kuznetsova IE,Nedospasov IA,Kolesov VV,Qian Z,Wang B,Zhu F

    更新日期:2018-05-01 00:00:00

  • Architectures for ultrasonic planetary sample retrieval tools.

    abstract::Traditional rotary corers and sample retrieval mechanisms for planetary drilling suffer from a variety of technical difficulties. A heavy and rigid drillstring must be assembled on-site and deployed with considerable applied preload and torque, and these mechanical loadings are difficult to react in a low gravity envi...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2011.06.001

    authors: Harkness P,Lucas M,Cardoni A

    更新日期:2011-12-01 00:00:00

  • Speckle tracking for multi-dimensional flow estimation.

    abstract::Speckle tracking methods overcome the major limitations of current Doppler methods for flow imaging and quantification: angle dependence and aliasing. In this paper, we review the development of speckle tracking, with particular attention to the advantages and limitations of two-dimensional algorithms that use a singl...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00182-1

    authors: Bohs LN,Geiman BJ,Anderson ME,Gebhart SC,Trahey GE

    更新日期:2000-03-01 00:00:00

  • Two approaches to multiple specular echo detection using split spectrum processing: moving bandwidth minimization and mathematical morphology.

    abstract::A split spectrum processing technique using a novel moving bandwidth minimization (MBM) method was developed to detect multiple specular targets having different spectral characteristics. Mathematical morphology (MM) algorithms were also implemented in order to compare the results. An experimental approach to optimal ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00024-4

    authors: Grevillot M,Cudel C,Meyer JJ,Jacquey S

    更新日期:1999-09-01 00:00:00

  • Interior dynamics of subharmonious surface wave in an idealized bidimensional granular layer.

    abstract::In this paper, high-speed photography was used to investigate the intrinsic dynamics of subharmonious surface wave in a vertical vibrated and idealized bidimensional granular layer. Using the high-speed photography, velocity fields of the granular layer at different stages through two cycles were obtained, which show ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.196

    authors: Zhang P,Huang K,Miao G,Wei R

    更新日期:2006-12-22 00:00:00

  • Analysis of second harmonic guided waves in pipes using a large-radius asymptotic approximation for axis-symmetric longitudinal modes.

    abstract::Theoretical formulation for the problem of second harmonic guided waves in pipes is presented from the principles of continuum mechanics. The formulation is carried out in the reference configuration of the pipe with an emphasis on the correct use of the "Divergence" operator in the reference configuration. Second har...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2012.12.007

    authors: Chillara VK,Lissenden CJ

    更新日期:2013-04-01 00:00:00

  • Waveguides in medical ultrasonics: an experimental study of mode propagation.

    abstract::Experimental results of ultrasound of varying frequency (0.8-5.0 MHz) propagating in cold drawn wires of stainless steel and aluminium ranging in diameter from 0.25 to 1.21 mm are in close agreement with theoretical predictions. This agreement is maintained when the coupling medium between the wire and the ultrasound ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(89)90021-8

    authors: Nicholson NC,McDicken WN,Anderson T

    更新日期:1989-03-01 00:00:00

  • Dynamic modeling and experimental verification of a piezoelectric part feeder in a structure with parallel bimorph beams.

    abstract::The study is aimed to perform dynamic modeling of a part feeder powered by piezoelectric actuation. This part feeder consists mainly of a horizontal platform vibrated by a pair of parallel piezoelectric bimorph beams. Owing to intermittent impacts with the platform, the transported part on the platform is able to marc...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2007.02.002

    authors: Chao PC,Shen CY

    更新日期:2007-06-01 00:00:00

  • A multiscale poromicromechanical approach to wave propagation and attenuation in bone.

    abstract::Ultrasonics is an important diagnostic tool for bone diseases, as it allows for non-invasive assessment of bone tissue quality through mass density-elasticity relationships. The latter are, however, quite complex for fluid-filled porous media, which motivates us to develop a rigorous multiscale poromicrodynamics appro...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.12.005

    authors: Morin C,Hellmich C

    更新日期:2014-07-01 00:00:00

  • Three-dimensional modelling of micromachined-ultrasonic-transducer arrays operating in water.

    abstract::We report on the 3-D modelling of periodic arrays of capacitive micromachined ultrasonic transducers (cMUTs) operating in fluid. Specific developments have been performed to model biperiodic transducer arrays and to take into account radiation into any stratified media at the front-side as well as the back-side of the...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.09.006

    authors: Wilm M,Reinhardt A,Laude V,Armati R,Daniau W,Ballandras S

    更新日期:2005-05-01 00:00:00

  • Reconstruction of ultrasonic fields by deconvolving the hydrophone aperture effects. I. Theory and simulation.

    abstract::In many ultrasound applications-especially in the area of medical diagnostics-conventional sensors and particularly piezoelectric hydrophones do not comply with the requirements for "point detectors". It therefore suggests itself to develop methods, which allow ultrasonic fields to be reconstructed from the spatially ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(02)00346-3

    authors: Boutkedjirt T,Reibold R

    更新日期:2002-08-01 00:00:00