Experimental and numerical investigations of mechanical displacements in surface acoustic wave bounded beams.

Abstract:

:The present paper studies experimentally and numerically the surface acoustic wave (SAW) field on a piezoelectric substrate generated by interdigital transducers (IDT). On the one hand, mechanical displacements produced by the SAW are measured with the help of a laser Doppler vibrometer. On the other hand, mechanical displacements are computed by the two-dimensional finite element method in frequency domain followed by the spatial Fourier transform. Combining these two steps of computations results in the intended two-dimensional distribution of mechanical displacements on the substrate surface. The comparison of experimental and numerical data obtained for a series of different IDTs reveals that it is possible to estimate the shape of the SAW beam and the absolute value of mechanical displacement amplitude using only the basic parameters of the IDT and its electrical admittance measured by a network analyzer.

journal_name

Ultrasonics

journal_title

Ultrasonics

authors

Weser R,Darinskii AN,Weihnacht M,Schmidt H

doi

10.1016/j.ultras.2020.106077

subject

Has Abstract

pub_date

2020-08-01 00:00:00

pages

106077

eissn

0041-624X

issn

1874-9968

pii

S0041-624X(20)30016-0

journal_volume

106

pub_type

杂志文章
  • Surface and quasi-longitudinal acoustic waves in KTiOAsO₄ single crystals.

    abstract::Surface and quasi-longitudinal acoustic wave properties have been investigated in potassium titanyl arsenate (KTiOAsO₄, KTA) single crystals for the first time. Surface acoustic wave (SAW) velocity, electromechanical coupling coefficient and power flow angle characteristics have been obtained in rotated Y-cut of KTA c...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.09.019

    authors: Taziev RM

    更新日期:2014-02-01 00:00:00

  • Detecting broken-wire flaws at multiple locations in the same wire of prestressing strands using guided waves.

    abstract::Broken wires often occur at multiple locations in the same wire of a strand due to the recovery length, which is defined as the length of the wire taking up its full share of the axial load from the break point. The detection of broken-wire flaws at multiple locations along the same wire is investigated using guided w...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2012.05.003

    authors: Xu J,Wu X,Sun P

    更新日期:2013-01-01 00:00:00

  • Sonodynamic action of hypocrellin B triggers cell apoptoisis of breast cancer cells involving caspase pathway.

    abstract:OBJECTIVES:The aim of the present study is to investigate the effects of sonodynamic action of hypocrellin B on human breast cancer cells and further explore its underlying mechanisms. METHODS:The cell viability of breast cancer MDA-MB-231 cells was examined by 3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyl tetrazolium b...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.09.013

    authors: Jia Y,Wang X,Liu Q,Leung AW,Wang P,Xu C

    更新日期:2017-01-01 00:00:00

  • Two approaches to multiple specular echo detection using split spectrum processing: moving bandwidth minimization and mathematical morphology.

    abstract::A split spectrum processing technique using a novel moving bandwidth minimization (MBM) method was developed to detect multiple specular targets having different spectral characteristics. Mathematical morphology (MM) algorithms were also implemented in order to compare the results. An experimental approach to optimal ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00024-4

    authors: Grevillot M,Cudel C,Meyer JJ,Jacquey S

    更新日期:1999-09-01 00:00:00

  • Acoustically assisted removal of nitrogen oxide from high temperature flue gas.

    abstract::The present study focuses on a possibility for improving NO removal efficiency from flue gas by application of powerful sound waves. The sound waves (frequency 6.9-17.2kHz, intensity 144-160dB) are propagated from Hartmann sound generators to a preheated graphite disk inside a vertical reaction tube (height 1.8m, I.D....

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.06.010

    authors: Komarov SV,Nemeth S,Hirasawa M

    更新日期:2005-02-01 00:00:00

  • Periodic shock-emission from acoustically driven cavitation clouds: a source of the subharmonic signal.

    abstract::Single clouds of cavitation bubbles, driven by 254kHz focused ultrasound at pressure amplitudes in the range of 0.48-1.22MPa, have been observed via high-speed shadowgraphic imaging at 1×10(6) frames per second. Clouds underwent repetitive growth, oscillation and collapse (GOC) cycles, with shock-waves emitted periodi...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.06.011

    authors: Johnston K,Tapia-Siles C,Gerold B,Postema M,Cochran S,Cuschieri A,Prentice P

    更新日期:2014-12-01 00:00:00

  • DC effects, sub-harmonics, stochasticity and "memory" for contact acoustic non-linearity.

    abstract::Acoustic wave interaction with non-bonded contacts was found to be inherently non-linear due to asymmetrical stiffness distribution across the interface. A diode-type non-linearity results in local static elastic fields inside the contact, which are shown to be a source of transient longitudinal and shear DC-acoustic ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(02)00241-x

    authors: Korshak BA,Solodov IY,Ballad EM

    更新日期:2002-05-01 00:00:00

  • SH ultrasonic guided waves for the evaluation of interfacial adhesion.

    abstract::Shear-Horizontally (SH) polarized, ultrasonic, guided wave modes are considered in order to infer changes in the adhesive properties at several interfaces located within an adhesive bond joining two metallic plates. Specific aluminium lap-joint samples were produced, with different adhesive properties at up to four in...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2014.03.002

    authors: Castaings M

    更新日期:2014-09-01 00:00:00

  • Potential of ultrasonic pulse velocity for evaluating the dimensional stability of oak and chestnut wood.

    abstract::The objective of this study was to examine the potential of ultrasonic velocity as a rapid and nondestructive method to predict the dimensional stability of oak (Quercus petraea (Mattuschka) Lieblein) and chestnut (Castanea sativa Mill.) that are commonly used in flooring industry. Ultrasonic velocity, specific gravit...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2015.11.007

    authors: Dündar T,Wang X,As N,Avcı E

    更新日期:2016-03-01 00:00:00

  • Spectral analysis of Doppler ultrasonic decompression data.

    abstract::Several aspects of spectral analysis of bubble transients in Doppler ultrasonic decompression data are discussed. The computation of energy density spectra, using fast Fourier transform techniques for analyzing bubble transients, is described. Spectral analysis of data from probes implanted within animals, using a con...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/0041-624x(77)90026-9

    authors: Kisman K

    更新日期:1977-05-01 00:00:00

  • Acousto-optic interaction with leaky surface acoustic waves in Y-cut LiTaO3 crystals.

    abstract::The acousto-optic interaction with leaky surface acoustic wave radiation into the bulk of YX-cut LiTaO(3) crystals has been investigated. The light incidence and diffraction angles corresponding to the strongest acousto-optic interaction were calculated and measured as functions of the acoustic wave frequency. The dep...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2011.12.004

    authors: Belovickis J,Rimeika R,Ciplys D

    更新日期:2012-07-01 00:00:00

  • Comparison between experimental and 2-D numerical studies of multiple scattering in Inconel600 by means of array probes.

    abstract::Ultrasonic non-destructive testing of polycrystalline structures can be disturbed by scattering at grain boundaries. Understanding and modeling this so-called "structural noise" is crucial for characterization as well as detection purposes. Structural noise can be considered as a fingerprint of the material under inve...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.06.012

    authors: Shahjahan S,Rupin F,Aubry A,Chassignole B,Fouquet T,Derode A

    更新日期:2014-01-01 00:00:00

  • Third harmonic transmit phasing for SNR improvement in tissue harmonic imaging with Golay-encoded excitation.

    abstract:BACKGROUND:Ultrasound tissue harmonic signal generally provides superior image quality as compared to the linear signal. However, since the generation of the tissue harmonic signal is based on finite amplitude distortion of the propagating waveform, the penetration and the sensitivity in tissue harmonic imaging are mar...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2010.12.008

    authors: Shen CC,Shi TY

    更新日期:2011-07-01 00:00:00

  • Baseline subtraction technique in the frequency-wavenumber domain for high sensitivity damage detection.

    abstract::This paper suggests a method for high-sensitivity damage detection. The method is based on pitch-catch measurements of Lamb waves combined with a baseline subtraction technique in the frequency-wavenumber domain. Small amplitude converted modes, generated during the interaction of propagating waves with damage, can th...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.08.010

    authors: McKeon P,Yaacoubi S,Declercq NF,Ramadan S,Yaacoubi WK

    更新日期:2014-02-01 00:00:00

  • A new optical method for the detection of in-plane motion of ultrasound propagating in metals.

    abstract::This paper describes a laser optical technique for the detection of in-plane (IP) motion of ultrasonic waves propagating in solids. This interference-based laser optical technique includes a tiny square indentation with a width of about 30 microm on the sample surface and a relatively simple optical arrangement. The c...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.076

    authors: Yang CH,Tsai YC

    更新日期:2006-12-22 00:00:00

  • New applications for ultrasonic sensors in process industries.

    abstract::Today, sophisticated instruments and algorithms used for process control allow the efficient production of substances with the quality guaranteed to the customer. However, production and management techniques are changing. This article aims to analyze trends resulting from those changes from the point of view of ultra...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.047

    authors: Püttmer A

    更新日期:2006-12-22 00:00:00

  • Three-dimensional modelling of micromachined-ultrasonic-transducer arrays operating in water.

    abstract::We report on the 3-D modelling of periodic arrays of capacitive micromachined ultrasonic transducers (cMUTs) operating in fluid. Specific developments have been performed to model biperiodic transducer arrays and to take into account radiation into any stratified media at the front-side as well as the back-side of the...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.09.006

    authors: Wilm M,Reinhardt A,Laude V,Armati R,Daniau W,Ballandras S

    更新日期:2005-05-01 00:00:00

  • Non-linear actuation of cantilevers using giant magnetostrictive thin films

    abstract::In the present paper, we report the first results concerning a centimetre cantilever driven through non-linear effects in thin magnetostrictive films. Bimorph centimetre beams (24 mm x 5 mm) were designed using 160 microns thick glass and 0.4 micron thick multilayer TbFe/Fe films deposited via RF sputtering, using sev...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(99)00061-x

    authors: Tiercelin N,Pernod P,Preobrazhensky V V,Le Gall H,Ben Youssef J

    更新日期:2000-03-01 00:00:00

  • How many times should we repeat measuring liver stiffness using shear wave elastography?: 5-repetition versus 10-repetition protocols.

    abstract::The purpose of this study is to evaluate whether a 5-repetition liver stiffness (LS) measurement as the standard protocol of shear wave elastography (SWE) is comparable to a conventional 10-repetition measurement protocol and to identify factors that influence the reliability of the 5-repetition protocol. A total of 3...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.08.005

    authors: Choi SH,Jeong WK,Kim Y,Lim S,Kwon JW,Kim TY,Kim MY,Sohn JH

    更新日期:2016-12-01 00:00:00

  • A nondestructive method for estimation of the fracture toughness of CrMoV rotor steels based on ultrasonic nonlinearity.

    abstract::The objective of this paper is to develop a nondestructive method for estimating the fracture toughness (K(IC)) of CrMoV steels used as the rotor material of steam turbines in power plants. To achieve this objective, a number of CrMoV steel samples were heat-treated, and the fracture appearance transition temperature ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/s0041-624x(03)00154-9

    authors: Jeong H,Nahm SH,Jhang KY,Nam YH

    更新日期:2003-09-01 00:00:00

  • New nonlinear ultrasonic method for material characterization: Codirectional shear horizontal guided wave mixing in plate.

    abstract::A nonlinear ultrasonic method is proposed based on a group of newly discovered wave triplets where two primary codirectional shear-horizontal SH0 waves mix in a weakly nonlinear plate and generate a cumulative S0 Lamb wave at the sum frequency. Theoretical analyses show that any combination of two primary SH0 waves wh...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2019.04.001

    authors: Shan S,Hasanian M,Cho H,Lissenden CJ,Cheng L

    更新日期:2019-07-01 00:00:00

  • Solder joint failure localization of welded joint based on acoustic emission beamforming.

    abstract::A localization approach of welded joint damage is proposed based on acoustic emission (AE) beamforming. In this method, a uniform line array is introduced to detect the AE signal of welded joints in specified area. In order to investigate the influence of fillet and crimping commonly existing in a welded plate structu...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.11.002

    authors: Liu X,Xiao D,Shan Y,Pan Q,He T,Gao Y

    更新日期:2017-02-01 00:00:00

  • Optimized ultrasonic attenuation measures for non-homogeneous materials.

    abstract::In this paper the study of frequency-dependent ultrasonic attenuation in strongly heterogeneous materials is addressed. To determine the attenuation accurately over a wide frequency range, it is necessary to have suitable excitation techniques. Three kinds of transmitted signals have been analysed, grouped according t...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2015.09.007

    authors: Genovés V,Gosálbez J,Carrión A,Miralles R,Payá J

    更新日期:2016-02-01 00:00:00

  • Depth-of-field enhancement in Filtered-Delay Multiply and Sum beamformed images using Synthetic Aperture Focusing.

    abstract::The Synthetic Aperture Focusing (SAF) technique makes it possible to achieve a higher and more uniform quality of ultrasound images throughout depth, as if both transmit and receive dynamic focusing were applied. In this work we combine a particular implementation of SAF, called Synthetic Transmit Aperture (STA) techn...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2016.11.022

    authors: Matrone G,Savoia AS,Caliano G,Magenes G

    更新日期:2017-03-01 00:00:00

  • Ultrasonic spectroscopy of pure cyclic compounds.

    abstract::Ultrasonic studies of the group of halogens of benzene and particularly dependence of acoustic parameters on the structure of organic liquids, demonstrate some interesting regularities in the group of these compounds in gas and liquid states. In this paper results for five cyclic liquids: bromo-, chloro-, fluoro- and ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.146

    authors: Linde BB,Lezhnev NB

    更新日期:2006-12-22 00:00:00

  • Arbitrary shaped, liquid filled reverberators with non-resonant transducers for broadband focusing of ultrasound using Time Reversed Acoustics.

    abstract::The ability to generate short focused ultrasonic pulses with duration on the order of one period of carrier frequency depends on the bandwidth of the transmitter as the pulse duration is inversely proportional to the bandwidth. Conventional focusing arrays used for focusing ultrasound have limited bandwidth due to the...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2008.10.008

    authors: Sarvazyan A,Fillinger L

    更新日期:2009-03-01 00:00:00

  • Lamb wave propagation in a plate with a grooved surface with several spatial periodicities.

    abstract::In order to investigate non-destructively the bonding between rough plates, the problem of Lamb waves propagating on a rough plate is addressed in this paper. Numerical analysis is performed on periodical gratings made of identical triangular grooves. If the surface profile is made up of grooves with one periodicity, ...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.05.052

    authors: Leduc D,Morvan B,Hladky AC,Pareige P,Izbicki JL

    更新日期:2006-12-22 00:00:00

  • Development of SH-SAW sensors for underwater measurement.

    abstract::We developed SH (shear horizontal) surface acoustic wave (SAW) sensors to detect protein molecules in liquid solutions applying a particular antibody thin film on the delay line of transverse SAW devices. The antibody investigated was human-immuno-globulin G (HigG) to hold the antigens (anti-HigG) in the protein solut...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2004.01.039

    authors: Kwon Y,Roh Y

    更新日期:2004-04-01 00:00:00

  • Ultrasonic strain imaging and reconstructive elastography for biological tissue.

    abstract::Mechanical properties of biological tissue represent important diagnostic information and are of histological and pathological relevance. In order to obtain non-invasively mechanical properties of tissue, we developed a real-time strain imaging system for clinical applications. The output data of this system also allo...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2006.06.007

    authors: Khaled W,Reichling S,Bruhns OT,Ermert H

    更新日期:2006-12-22 00:00:00

  • A multiscale poromicromechanical approach to wave propagation and attenuation in bone.

    abstract::Ultrasonics is an important diagnostic tool for bone diseases, as it allows for non-invasive assessment of bone tissue quality through mass density-elasticity relationships. The latter are, however, quite complex for fluid-filled porous media, which motivates us to develop a rigorous multiscale poromicrodynamics appro...

    journal_title:Ultrasonics

    pub_type: 杂志文章

    doi:10.1016/j.ultras.2013.12.005

    authors: Morin C,Hellmich C

    更新日期:2014-07-01 00:00:00