Abstract：
:Broken wires often occur at multiple locations in the same wire of a strand due to the recovery length, which is defined as the length of the wire taking up its full share of the axial load from the break point. The detection of broken-wire flaws at multiple locations along the same wire is investigated using guided waves below 400kHz. Herein, a sample with three broken-wire flaws in the same wire is analyzed using magnetostrictive guided waves. Our data show that three flaws are found using the low-frequency guided waves (50kHz) but only one flaw is found using the high-frequency guided waves (320kHz). By analyzing the reflection and transmission coefficients at the three different flaws, we observe that the energy exchange decreases as the frequency increases along the same propagating distance. Hence, the recovery length for elastic waves, the length of the wire taking up its full share of elastic-wave energy from the break point, is observed. The recovery length for elastic waves in prestressing strands increases with the frequency. To detect prestressing strands using magnetostrictive guided waves, several one-broken-wire flaws at different locations can be distinguished from in different wires or the same wire by employing both low-frequency waves and high-frequency waves. Nevertheless, we cannot identify in which wire the flaws are located because the magnetostrictive sensor analyzes the whole strand.
journal_name
Ultrasonicsjournal_title
Ultrasonicsauthors
Xu J,Wu X,Sun Pdoi
10.1016/j.ultras.2012.05.003subject
Has Abstractpub_date
2013-01-01 00:00:00pages
150-6issue
1eissn
0041-624Xissn
1874-9968pii
S0041-624X(12)00100-Xjournal_volume
53pub_type
杂志文章相关文献
ULTRASONICS文献大全abstract：:The threshold filter is a frequently used technique in ultrasound B-scan to reject the small echoes contributed from backscattering that blur the tissue interface and reduce the image contrast. Note that using the threshold based on one value would simultaneously destroy local waveform features of the reflection echoe...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2008.10.007
更新日期：2009-05-01 00:00:00
abstract：:The results of computer simulation taking into account the linear and nonlinear material constants have been presented. Study of the influence of external uniaxial mechanical stress on the dispersive characteristics of elastic waves in piezoelectric structures as "La3Ga5SiO14/fused silica" has been executed. The compa...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.07.007
更新日期：2015-01-01 00:00:00
abstract：:Geometrical and material property changes cause deviations in the resonant conditions used for noncollinear wave mixing. These deviations are predicted and observed using the SV(ω1)+L(ω2)→L(ω1+ω2) interaction, where SV and L are the shear vertical and longitudinal waves, respectively, and ω1, ω2 are their frequencies....
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.11.009
更新日期：2015-03-01 00:00:00
abstract：:The design and simulation of power transducers are difficult since piezoelectric, dielectric and elastic properties of ferroelectric materials differ from linear behavior when driven at large levels. This paper is devoted to modeling of a resonant power transducer at a high level of dynamic mechanical stress. The powe...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2011.05.017
更新日期：2011-12-01 00:00:00
abstract：:This paper presents a novel linear piezoelectric motor which is suitable for rapid ultra-precision positioning. The finite element analysis (FEA) was applied for optimal design and further analysis, then experiments were conducted to investigate its performance. By changing the input signal, the proposed motor was fou...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.07.010
更新日期：2016-12-01 00:00:00
abstract：:Exposure of Petunia hybrida cell suspensions to ultrasound at a frequency of 2.43 MHz in a standing wave field at an energy density of 70 Jm-3 (pressure amplitude of 0.78 MPa) decreased their mean viability to 35% after 20 min of sonication. A comparison of propagating wave and standing wave treatments at equal freque...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(99)00166-3
更新日期：2000-03-01 00:00:00
abstract：:Electromagnetic-acoustic transducers (EMATs) consist of a magnet and a coil. They are advantageous in some non-destructive evaluation (NDE) applications because no direct contact with the specimen is needed to send and receive ultrasonic waves. However, EMATs commonly require excitation peak powers greater than 1kW an...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.02.009
更新日期：2017-07-01 00:00:00
abstract：:The propagation of ultrasound through an austenitic weld is investigated experimentally as well as in a numerical simulation. The weld is insonified at normal incidence to the fusion line with a longitudinal contact transducer. In order to experimentally trace the ultrasound through the weld, slices of different thick...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(99)00103-1
更新日期：2000-03-01 00:00:00
abstract：:In this work, the existence of the optimal working frequency for ultrasonic motors (USMs) is theoretically and experimentally verified for the first time, at which working point the power dissipation of the motors arrives at its minimum value. The mathematical model of the mechanical quality factor is initially deduce...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.04.015
更新日期：2016-08-01 00:00:00
abstract：:Although ultrasonic energy is widely used cleaning and degreasing of parts and assemblies in automotive and other industries, the use of ultrasonic energy in an industrial scale for textile washing is very new. This is due to the complexity of controlling the combination of chemical and mechanical effects, whereas wit...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2004.02.005
更新日期：2004-04-01 00:00:00
abstract：:The goal standard of contrast echocardiography is the absolute measure of myocardial perfusion using a contrast agent. Actually, several contrast agents are developed. All these agents show left ventricular opacification after intravenous injection. However, none of these agents shows an acceptable enhancement of the ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(97)00137-6
更新日期：1998-02-01 00:00:00
abstract：:Development of acoustic source localization techniques in anisotropic plates has gained attention in the recent past and still has scope of improvement. Most of such techniques existing in the literature either require known material properties or assume a straight line propagation of wave energy from the acoustic sou...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.105977
更新日期：2020-01-01 00:00:00
abstract：:Nitric oxide (NO) has been implicated in smooth muscle relaxation. Its use has been widespread in cardiology. Due to the effective scavenging of NO by hemoglobin, however, the drug has to be applied locally or in large quantities, to have the effect desired. We propose the use of encapsulated microbubbles that act as ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.06.003
更新日期：2006-12-22 00:00:00
abstract：:In this paper, an optimization method aimed at designing aperiodic linear sparse arrays is proposed that is based on the stochastic optimization methodology called simulated annealing. Such a method optimizes the positions and the weight coefficients of each element of a linear array in order to obtain a beam pattern ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(99)00089-x
更新日期：2000-03-01 00:00:00
abstract：:Ultrasonic non-destructive testing of polycrystalline structures can be disturbed by scattering at grain boundaries. Understanding and modeling this so-called "structural noise" is crucial for characterization as well as detection purposes. Structural noise can be considered as a fingerprint of the material under inve...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2013.06.012
更新日期：2014-01-01 00:00:00
abstract：:Investigation was carried out to study the effects of maximum aggregate size (MAS) (12.5mm, 19.0mm, 25.0mm, 37.5mm, and 50.0mm) on ultrasonic pulse velocity (UPV) of concrete. For investigation, first class bricks were collected and broken to make coarse aggregate. The aggregates were tested for specific gravity, abso...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.04.006
更新日期：2016-07-01 00:00:00
abstract：:The layer-multiple-scattering method is developed to study wave propagation through two-dimensional lattices of cylindrical inclusions in an elastic medium. The lattices are a series of periodically spaced infinite one-dimensional periodic gratings (or rows) of inclusions. The layer-multiple-scattering method allows t...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.09.002
更新日期：2006-12-01 00:00:00
abstract：BACKGROUND AND OBJECTIVE:Acoustic scattering properties of ultrasound contrast agents are useful in extending existing or developing new techniques for biomedical imaging applications. A useful first step in this direction is to investigate the acoustic scattering of a new class of acoustic beams, known as helicoidal h...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.09.003
更新日期：2010-03-01 00:00:00
abstract：:Both pinnae of anaesthetized male guinea-pigs were contused in a reproducible manner and one immediately treated with 0.75 MHz ultrasound at an average therapeutic intensity of 0.61 W cm-2 for a period of 2 min. The lividity and rate of resorption of the rusultant bruises were measured by a photometric method. The res...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(78)90021-5
更新日期：1978-09-01 00:00:00
abstract：:The method of wave function expansion is adopted to study the three dimensional scattering of a time-harmonic plane progressive sound field obliquely incident upon a multi-layered hollow cylinder with interlaminar bonding imperfection. For the generality of solution, each layer is assumed to be cylindrically orthotrop...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.05.007
更新日期：2009-12-01 00:00:00
abstract：:The main component of every device used for investigating internal object structure by Ultrasound Transmission Tomography (UTT) is a special ultrasonic probe. This paper presents the structure of model multielement ring probe for examining objects using this method in divergent ray projection geometry. The probe is ma...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.05.126
更新日期：2006-12-22 00:00:00
abstract：:Sonoelectrochemistry is undergoing a reemerging activity in the last years with an increasing number of papers appearing in a wide range of peer review journals. Applied studies which cover environmental treatments, synthesis or characterization of nanostructures, polymeric materials synthesis, analytical procedures, ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.09.022
更新日期：2010-02-01 00:00:00
abstract：:The main challenge faced by 3D ultrasonic imaging with 2D array transducers is the large number of elements required to achieve an acceptable level of quality in the images. Therefore, the optimisation of the array layout, in order to reduce the number of active elements in the aperture, has been a research topic in t...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.09.010
更新日期：2010-02-01 00:00:00
abstract：:Aluminium sheet thickness has been calculated from ultrasonic data obtained using a send-receive, radially polarised electromagnetic acoustic transducer (EMAT). Sheets in the thickness range between 0.1 and 0.5 mm have been measured using this non-contact approach at a stand-off of up to 1.5 mm. Normal incidence shear...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(01)00083-x
更新日期：2001-10-01 00:00:00
abstract：:This paper proposes a new pair of sequences whose cross-correlation values are zero except for the peak value and presents a new modulation method for an ultrasonic Doppler flowmeter with high sensitivity utilizing these sequences. In this method, transmitted and received waves are modulated and demodulated, respectiv...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(79)90023-4
更新日期：1979-11-01 00:00:00
abstract：:In this paper, the radial basis function (RBF) collocation method based on the nonlocal Eringen piezoelectricity theory is developed to compute the band structures of nanoscale multilayered piezoelectric phononic crystals taking account of nonlocal interface effects. Detailed calculations are performed for anti-plane ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.09.009
更新日期：2017-01-01 00:00:00
abstract：:During the last decade, the introduction of ultrasound techniques in arc welding with the intention of improving the operational performance and technical characteristics of the welding processes have been studied intensively. In this work is presented a broad review of the literature surrounding the utilization of th...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.10.007
更新日期：2015-02-01 00:00:00
abstract：:The paper investigates the existence of interfacial (Stoneley-type) acoustic waves localised at the internal boundary between two semi-infinite superlattices which are adjoined with each other to form one-dimensional phononic bicrystal. Each superlattice is a periodic sequence of perfectly bonded homogeneous and/or fu...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2020.106237
更新日期：2021-01-01 00:00:00
abstract：:This study investigated the effect of LIPUS on fracture healing when fractures were exposed to ultrasound at three axial distances: z=0 mm, 60 mm, and 130 mm. We applied LIPUS to rat fracture at these three axial distances mimicking the exposure condition of human fractures at different depths under the soft tissue. M...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2013.10.013
更新日期：2014-03-01 00:00:00
abstract：:Traditional rotary corers and sample retrieval mechanisms for planetary drilling suffer from a variety of technical difficulties. A heavy and rigid drillstring must be assembled on-site and deployed with considerable applied preload and torque, and these mechanical loadings are difficult to react in a low gravity envi...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2011.06.001
更新日期：2011-12-01 00:00:00
