Abstract:
:In total hip arthroplasty, osteolysis of the acetabulum often occurs at the backside of cups in the area of screw holes, indicating a clinically relevant amount of polyethylene (PE) wear particles in this area. In order to avoid a possible migration of wear particles to the acetabulum-bone, screw hole plugs are provided for some implant systems. The aims of this study were to quantitatively determine backside wear and to investigate the migration behaviour of articulation-related wear particles in a cup system with open and closed screw holes by plugs. Titanium cup systems with backside holes for screw fixations were sinusoidally loaded with 2.7 kN. The articulation area was separated from the backside area of the cup. A defined amount of articulation-generated particles was added to the fluid of the articulation chamber. The fluids in the two chambers were separately filtered after 2 × 106 cycles for a particle analysis. Backside wear with noticeably small (65.6 ± 4.2 nm) and round PE particles was identified. With both open and closed screw holes, a migration of the articulating wear particles from the articulation area behind the cup could be observed. Backside wear was estimated to be below 1% of the articulated wear. Screw hole plugs did not effectively prevent the migration of PE wear particles behind the investigated cups. STATEMENT OF SIGNIFICANCE: Backside wear occurs in a proven cup-system. Furthermore, it was quantitatively observed that articulation-generated wear products could migrate from the articulating area along the cup/liner-interface through the screw holes behind the cup. An almost unimpeded particle migration to the acetabulum-bone, in conjunction with very small backside wear particles, could produce a clinically relevant amount of PE with respect to pelvic lysis. These findings highlight the importance of management to avoid particle migration in artificial hip cups. Therefore, primarily the use of screw hole plugs, as far as available for the respective cup-system, is recommended. The aim of avoiding particle migration by plugs, but also by using a sophisticated anchoring mechanism between cup and PE liner should continue in future.
journal_name
Acta Biomaterjournal_title
Acta biomaterialiaauthors
Braun S,Vardag S,Mueller U,Schroeder S,Sonntag R,Bormann T,Gotterbarm T,Kretzer JPdoi
10.1016/j.actbio.2019.07.050subject
Has Abstractpub_date
2019-10-01 00:00:00pages
239-246eissn
1742-7061issn
1878-7568pii
S1742-7061(19)30539-2journal_volume
97pub_type
杂志文章abstract:UNLABELLED:Cardiovascular disease is the leading cause of death in the world. In this study, coaxial electrospinning is employed to fabricate fibers in a core-shell structure with polyvinyl alcohol (PVA) in the core and gelatin in the shell for evaluation as a potential vascular tissue engineering construct. PVA, a syn...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2015.08.044
更新日期:2015-11-01 00:00:00
abstract::A biphasic layer with a Zn-containing beta-tricalcium phosphate (ZnTCP) phase and a fluoridated hydroxyapatite (FHA) phase on titanium alloy substrate was prepared by the sol-gel technique. Scanning electron microscopy and energy-dispersive X-ray analysis results showed the ZnTCP/FHA layer to have a heterogeneous surf...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2007.08.013
更新日期:2008-03-01 00:00:00
abstract::The performance of total hip-joint replacements depends strongly on the state of lubrication in vivo. In order to test candidate prosthetic materials, in vitro wear testing requires a lubricant that behaves in the same manner as synovial fluid. The current study investigated three lubricants and looked in detail at th...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2011.12.037
更新日期:2012-07-01 00:00:00
abstract::The aim of this work was to study the phase transformation during the setting reaction of two calcium phosphate bone cements based on either alpha tricalcium phosphate (alpha-TCP) or tetracalcium phosphate (TetCP) initial solid phase, and a magnesium carbonate-phosphoric acid solution as the hardening liquid. Low mole...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2008.01.006
更新日期:2008-07-01 00:00:00
abstract::Molecular imprinting is a new and rapidly evolving technique used to create synthetic receptors and it possesses great potential in a number of applications in the life sciences. Keeping in mind the therapeutic importance of 5-fluorouracil (5-FU) and the technological significance of molecular imprinting polymers, the...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2008.03.017
更新日期:2008-09-01 00:00:00
abstract::This paper investigates the effects of moisture, anisotropy, stress state, and strain rate on the mechanical properties of the bighorn sheep (Ovis Canadensis) horn keratin. The horns consist of fibrous keratin tubules extending along the length of the horn and are contained within an amorphous keratin matrix. Samples ...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2016.10.033
更新日期:2017-01-15 00:00:00
abstract::In this study, we report the synthesis of novel environmentally responsive polyurea hydrogel networks prepared via organic sol-gel chemistry and demonstrate that the networks can stabilize pH while releasing glucose both in simple aqueous media and in mammalian cell culture settings. Hydrogel formulations have been de...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2012.04.040
更新日期:2012-08-01 00:00:00
abstract::Ocular inflammation is one of the leading causes of blindness worldwide, and steroids in topical ophthalmic solutions (e.g. dexamethasone eye drops) are the mainstay of therapy for ocular inflammation. For many non-infectious ocular inflammatory diseases, such as uveitis, eye drops are administered as often as once ev...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2020.08.013
更新日期:2020-10-15 00:00:00
abstract::A challenge in using bioactive melt-derived glass in bone regeneration is to produce scaffolds with interconnected pores while maintaining the amorphous nature of the glass and its associated bioactivity. Here we introduce a method for creating porous melt-derived bioactive glass foam scaffolds with low silica content...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2017.04.030
更新日期:2017-07-15 00:00:00
abstract::The quest for predictive tumor markers for osteosarcoma (OS) has not well progressed over the last two decades due to a lack of preclinical models. The aim of this study was to investigate if microenvironmental modifications in an original humanized in vivo model alter the expression of OS tumor markers. Human bone mi...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2019.02.051
更新日期:2019-04-15 00:00:00
abstract::Breast cancer has become the second leading cause of cancer-related mortality in female wherein more than 90% of breast cancer-related death results from cancer metastasis to distant organs at advanced stage. The purpose of this study is to develop biodegradable nanoparticles composed of natural polypeptides and calci...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2017.06.008
更新日期:2017-08-01 00:00:00
abstract::Dicalcium phosphate dihydrate (brushite) is an osteoconductive biomaterial with great potential as a bioresorbable cement for bone regeneration. Preset brushite cement can be dehydrated into dicalcium phosphate anhydrous (monetite) bioceramics by autoclaving. This heat treatment results in changes in the physical char...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2012.04.025
更新日期:2012-08-01 00:00:00
abstract::Patterned surfaces direct cell spatial dynamics, yielding cells oriented along the surface geometry, in a process known as contact guidance. The Rho family of GTPases controls the assembly of focal adhesions and cytoskeleton dynamics, but its role in modulating bone-cell alignment on patterned surfaces remains unknown...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2010.11.035
更新日期:2011-04-01 00:00:00
abstract::It is challenging for traditional hemostatic sponges to meet the clinic demand for both uncontrolled and noncompressible hemorrhage. With the aim to develop a rapid shape recovery material with both active and passive hemostatic performance, a dual-functional hemostatic sponge (TRAP-Sp) with a macroporous structure an...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2019.08.039
更新日期:2019-11-01 00:00:00
abstract::The wide variety of diatom frustule shapes and intricate architectures provide viable prototypes to guide the design and fabrication of nanodevices and nanostructured materials for applications ranging from sensors to nanotemplates. In this study, a combined experimental-simulation method was developed to probe the po...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2015.07.028
更新日期:2015-10-01 00:00:00
abstract::Functional and perfusable vascular network formation is critical to ensure the long-term survival and functionality of engineered tissues after their transplantation. Although several vascularization strategies have been reviewed in past, the significance of microvessel organization in three-dimensional (3D) scaffolds...
journal_title:Acta biomaterialia
pub_type: 杂志文章,评审
doi:10.1016/j.actbio.2019.03.016
更新日期:2019-09-01 00:00:00
abstract::The main objective of this study was to investigate calcium phosphate (CaP) coatings on Ti6Al4V substrates by using the biomimetic technique. To this purpose, a new solution was developed to coat CaP on Ti6Al4V alloy substrates. The newly formulated body fluid (Lac-SBF) contained appropriate amounts of sodium lactate ...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2009.12.013
更新日期:2010-06-01 00:00:00
abstract::Implant-derived material from metal-on-metal (MOM) hip arthroplasties may be responsible for an unexplained tissue inflammatory response. The chemical form of the metal species in the tissues is predominantly chromium (Cr), but the currently used techniques have not been able to determine whether this is Cr(III) phosp...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2010.06.006
更新日期:2010-11-01 00:00:00
abstract::Antimicrobial peptides (AMPs) are currently receiving interest as an alternative to conventional antibiotics to treat biomaterial-associated infection. However, the inherent instability of such peptides often limits their efficacy in intended clinical applications. Covalent immobilization of AMPs to surfaces is one st...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2018.10.039
更新日期:2019-01-01 00:00:00
abstract::Corneal blindness is traditionally treated by transplantation of a donor cornea, or in severe cases by implantation of an artificial cornea or keratoprosthesis. Due to severe donor shortages and the risks of complications that come with artificial corneas, tissue engineering in ophthalmology has become more focused on...
journal_title:Acta biomaterialia
pub_type: 杂志文章,评审
doi:10.1016/j.actbio.2018.01.023
更新日期:2018-03-15 00:00:00
abstract::There is growing interest in the use of synthetic biomaterials to deliver inorganic ions that are known to stimulate angiogenesis and osteogenesis in vivo. In the present study, we investigated the effects of varying amounts of copper in a bioactive glass on the response of human bone marrow-derived mesenchymal stem c...
journal_title:Acta biomaterialia
pub_type: 杂志文章,收录出版
doi:10.1016/j.actbio.2014.12.010
更新日期:2015-03-01 00:00:00
abstract::Biodegradable metals have been suggested as revolutionary biomaterials for bone-grafting therapies. Of these metals, magnesium (Mg) and its biodegradable alloys appear to be particularly attractive candidates due to their non-toxicity and as their mechanical properties match those of bones better than other metals do....
journal_title:Acta biomaterialia
pub_type: 杂志文章,评审
doi:10.1016/j.actbio.2014.02.026
更新日期:2014-07-01 00:00:00
abstract::Perinatal tissues are an abundant source of human extracellular matrix proteins, growth factors and stem cells with proved potential use in a wide range of therapeutic applications. Due to their placental origin, these tissues possess unique biological properties, including being angiogenic, anti-inflammatory, anti-fi...
journal_title:Acta biomaterialia
pub_type: 杂志文章,评审
doi:10.1016/j.actbio.2020.04.035
更新日期:2020-07-01 00:00:00
abstract::Recent advances in biomaterials integrate metal nanoparticles with hydrogels to generate composite materials that exhibit new or improved properties. By precisely controlling the composition, arrangement and interactions of their constituents, these hybrid materials facilitate biomedical applications through myriad ap...
journal_title:Acta biomaterialia
pub_type: 杂志文章,评审
doi:10.1016/j.actbio.2020.12.030
更新日期:2020-12-19 00:00:00
abstract::The development of polyelectrolyte multilayered coatings on magnesium alloy substrates that can be used for controlled delivery of growth factors and required biomolecules from the surface of these degradable implants could have a significant impact in the field of bone tissue regeneration. The current work reports on...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2013.05.013
更新日期:2013-11-01 00:00:00
abstract::A three-dimensional (3-D) cell culture system that allows control of both substrate stiffness and integrin binding density was created and characterized. This system consisted of two self-assembling peptide (SAP) sequences that were mixed in different ratios to achieve the desired gel stiffness and adhesiveness. The s...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2013.04.002
更新日期:2013-08-01 00:00:00
abstract::The aim of this study was to fabricate a fibrous scaffold that closely resembled the micro-structural architecture and mechanical properties of collagen fibres found in the anterior cruciate ligament (ACL). To achieve this aim, fibrous scaffolds were made by electrospinning L-lactide based polymers. L-Lactide was chos...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2012.07.012
更新日期:2012-11-01 00:00:00
abstract::A series of six unique Ca-based bulk metallic glasses were synthesized and characterized. The glasses were designed to consist solely of the biocompatible elements Ca, Mg and Zn, with the view to their potential use as bioresorbable metals for orthopaedic applications. The alloys had a critical casting thickness of up...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2012.03.009
更新日期:2012-07-01 00:00:00
abstract::Biodegradability is a crucial characteristic to improve the clinical potential of sol-gel-derived glass materials. To this end, a set of degradable organic/inorganic class II hybrids from a tetraethoxysilane(TEOS)-derived silica sol and oligovalent cross-linker oligomers containing oligo(d,l-lactide) domains was devel...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2017.09.024
更新日期:2017-11-01 00:00:00
abstract::Cartilaginous tissues engineered using mesenchymal stem cells (MSCs) have been shown to generate bone in vivo by executing an endochondral programme. This may hinder the use of MSCs for articular cartilage regeneration, but opens the possibility of using engineered cartilaginous tissues for large bone defect repair. H...
journal_title:Acta biomaterialia
pub_type: 杂志文章
doi:10.1016/j.actbio.2014.11.031
更新日期:2015-02-01 00:00:00