Abstract：
:Monolithic dental prostheses fabricated from 3 mol.% yttria-stabilized zirconia (3YZ) are becoming increasingly popular. Recently, 5 mol.% yttria-stabilized zirconia (5YZ) which significantly improves the translucency of 3YZ has been prepared. However, its mechanical and microstructural properties, especially those affected by low-temperature degradation (LTD), have not been fully elucidated yet. The objective of the present study was to establish the relationship between the flexural strength of 5YZ with or without autoclave-induced LTD and its microstructural properties. For this purpose, a total of 320 bar-shaped specimens were cut from 5YZ and 3YZ blocks, and half of the specimens in each group were autoclaved at 134 °C for 50 h. Their flexural strengths were determined by conducting three-point bending tests, and the obtained results were analyzed by the Weibull statistical method. Grain sizes and crystalline structures of the specimens were analyzed by scanning electron microscopy (SEM) and X-ray diffraction, respectively. Additionally, the LTD-induced phase transformation was examined by Raman microscopy and cross-sectional surface analysis. The characteristic strengths of 5YZ and 3YZ were approximately 620 and 950 MPa, respectively, and 5YZ was found to be more resistant to LTD in terms of phase transformation than 3YZ. However, a low amount of the monoclinic phase was detected even in 5YZ after 50 h of autoclaving, which significantly decreased its flexural strength and reliability. The results of SEM analysis revealed that 5YZ was composed of two distinct regions: a dominant matrix with large grains (median size: 0.8 μm) and scattered areas with small grains (median size: 0.4 μm). Phase transformation analysis and fractography data indicated that the small-grain region was strongly affected by LTD and likely represented a fracture origin. The described properties should be considered during the clinical application of monolithic 5YZ dental prostheses.
journal_name
J Mech Behav Biomed Materauthors
Harada A,Shishido S,Barkarmo S,Inagaki R,Kanno T,Örtengren U,Egusa H,Nakamura Kdoi
10.1016/j.jmbbm.2020.103974subject
Has Abstractpub_date
2020-11-01 00:00:00pages
103974eissn
1751-6161issn
1878-0180pii
S1751-6161(20)30526-9journal_volume
111pub_type
杂志文章abstract：:Grit blasting is used as a cost-effective method to increase the surface roughness of metallic biomaterials, as Ti6Al4V and 316 LVM, to enhance the osteointegration, fixation and stability of implants. Samples of these two alloys were blasted by using alumina and zirconia particles, yielding rough (up to Ra~8μm) and n...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.10.013
更新日期：2014-02-01 00:00:00
abstract：:The hierarchical architecture of the collagen fibril is well understood, involving non-integer staggering of collagen molecules which results in a 67 nm periodic molecular density variation termed D-banding. Other than this variation, collagen fibrils are considered to be homogeneous at the micro-scale and beyond. Int...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103849
更新日期：2020-10-01 00:00:00
abstract：:Tissue material properties are crucial to understanding their mechanical function, both in healthy and diseased states. However, in certain circumstances logistical limitations can prevent testing on fresh samples necessitating one or more freeze-thaw cycles. To date, the nature and extent to which the material proper...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.03.006
更新日期：2017-07-01 00:00:00
abstract：:The level of fatty acid saturation in phospholipids is a crucial determinant of the biophysical properties of the lipid bilayer. Integral membrane proteins are sensitive to changes of their bilayer environment such that their activities and localization can be profoundly affected. When incorporated into phospholipids ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.12.026
更新日期：2018-03-01 00:00:00
abstract：:We report linear and non-linear shear tests on rat skin, evidencing a strain-softening regime, from 1% to 50% strain, followed by a strong strain-hardening regime, leading to a 'deck chair-shaped' stress-strain curve. The strain-softening regime was never reported as such in the literature, possibly mistaken for the l...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.12.021
更新日期：2017-05-01 00:00:00
abstract：:Due to its proximity to the mitral valve, the coronary sinus (CS) vessel serves as a conduit for the deployment and implantation of the percutaneous transvenous mitral annuloplasty (PTMA) devices that can potentially reduce the mitral regurgitation. Because CS vessel is a venous tissue and seldom diseased, its mechani...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.09.001
更新日期：2012-02-01 00:00:00
abstract：:Polycarbonate polyurethane has cartilage-like, hygroscopic, and elastomeric properties that make it an attractive material for orthopedic joint replacement application. However, little data exists on the cyclic loading and fracture behavior of polycarbonate polyurethane. This study investigates the mechanisms of fatig...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.01.008
更新日期：2018-03-01 00:00:00
abstract：:New processing methods for shape-memory polymers allow for tailoring material properties for numerous applications. Shape-memory nonwovens have been previously electrospun, but melt blow processing has yet to be evaluated. In order to determine the process parameters affecting shape-memory behavior, this study examine...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.05.038
更新日期：2016-09-01 00:00:00
abstract：:This study investigated the biocompatibility of the experimental thermoplastic rubber Arbomatrix(™) that will be used as the protective coating on a novel intracranial pressure (ICP) sensor silicon chip. Arbomatrix(™) was benchmarked against biocompatible commercial silicone rubber shunt tubing in the brain via a rat ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.01.018
更新日期：2015-05-01 00:00:00
abstract：:In this study, the relationship between deformation mechanism and rolling reductions was investigated, and the effects of deformation reductions on the microstructure and mechanical properties of the alloys both cold rolled and aged were revealed. It was found that the equiaxed β grains of the Ti-30Nb-5Ta-6Zr alloy ha...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2013.06.006
更新日期：2013-11-01 00:00:00
abstract：:The use of micropatterning to create uniform surface morphologies has been cited as yielding improvements in the coefficient of friction during high velocity sliding contact. Studies have not been preformed to determine if these micropatterns could also be useful in biomedical applications, such as total joint replace...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.08.022
更新日期：2012-03-01 00:00:00
abstract：:In recent years, scaffolds produced in 3D printing technology have become more widespread tool due to providing more advantages than traditional methods in tissue engineering applications. In this research, it was aimed to produce patches for the treatment of tympanic membrane perforations which caused significant hea...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104219
更新日期：2021-02-01 00:00:00
abstract：BACKGROUND AND AIMS:The course and outcome of pregnancy is closely correlated to change of biomechanical properties of the uterine cervix. The aim of this study was to build a non-linear, fiber reinforced mechanical model of the cervix for estimation of mechanical characteristics of the cervix in early- and term-pregna...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.07.005
更新日期：2014-11-01 00:00:00
abstract：:The atrioventricular heart valve (AHV) leaflets are critical to the facilitation of proper unidirectional blood flow through the heart. Previously, studies have been conducted to understand the tissue mechanics of healthy AHV leaflets to inform the development of valve-specific computational models and replacement mat...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.103438
更新日期：2020-01-01 00:00:00
abstract：OBJECTIVES:The deviation and spread of values measured by tensile strength tests should be significantly reduced by optimized axially pull-off-device. MATERIAL AND METHODS:Factors like geometry, roughness, surface texture and fit of the specimens, the luting procedure (mixing ratio, compacting pressure) were standardi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.07.003
更新日期：2018-11-01 00:00:00
abstract：:The cytoskeleton is primarily responsible for providing structural support, localization and transport of organelles, and intracellular trafficking. The structural support is supplied by actin filaments, microtubules, and intermediate filaments, which contribute to overall cell elasticity to varying degrees. We evalua...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.01.022
更新日期：2016-08-01 00:00:00
abstract：:Surface finish of NiTi is widely perceived to affect its biocompatibility and corrosion fatigue performance. The aim of this work was to find out, whether a carefully engineered surface oxide shows any beneficial effect over electropolished surface on the fatigue performance of superelastic NiTi wire mechanically cycl...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104028
更新日期：2020-11-01 00:00:00
abstract：:Bioink plays a major role in 3D printing of tissues and organs. Alginate is a widely used component for bioinks but its cellular responses are limited, which limits its clinical translation. In this study, we demonstrate the printability and cellular compatibility of composite bioink consists of sodium alginate (NaAlg...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.103642
更新日期：2020-04-01 00:00:00
abstract：:The high-performance polymer PEEK (poly-ether-ether-ketone) is more and more being used in the field of dentistry, mainly for removable and fixed prostheses. In cases of screw-retained implant-supported reconstructions of PEEK, an abutment screw made of PEEK might be advantageous over a conventional metal screw due to...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2016.06.024
更新日期：2016-10-01 00:00:00
abstract：:Infection incidence for total hip and knee arthroplasty (THA and TKA, respectively) is between 0.2% and 5% and results in approximately 100,000 device failures per year in the United States. Treatment requires prolonged systemic antibiotic therapy with additional surgical revisions. As a prophylactic measure against i...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2018.06.033
更新日期：2018-11-01 00:00:00
abstract：:Zirconia implants are becoming a preference choice for different applications such as knee, dental, among others. In order to improve osseointegration, implant's surfaces are usually coated with bioactive materials like hydroxyapatite (HAp) and beta-tricalcium phosphate (β-TCP) that are very similar to the calcium pho...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.02.022
更新日期：2019-06-01 00:00:00
abstract：OBJECTIVES:To evaluate the interfacial adhesion of an autopolymerizing acrylic resin to 3D printed thermoset occlusal splints compared to thermoplastic occlusal splints. MATERIALS AND METHODS:Cylinders made of an autopolymerizing acrylic resin were adhered to 3D printed thermoset and also to thermoplastic plates. A di...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2019.04.011
更新日期：2019-07-01 00:00:00
abstract：:In the development of new materials for orthopedic implants, special attention has been given to Ti alloys that show biocompatible alloy elements and that are capable of reducing the elastic modulus. Accordingly, Ti-Nb-Si alloys show great potential for application. Thus, this is a study on the microstructures and pro...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2015.06.035
更新日期：2015-11-01 00:00:00
abstract：:Bone is a composite material consisting principally of apatite mineral, collagen fibrils, non-collagenous proteins, and other organic species. Recent electron microscopy studies have shown that the mineral in bone occurs as stacks of thin polycrystalline sheets ("mineral lamellae," MLs) which surround and lie between ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104132
更新日期：2021-01-01 00:00:00
abstract：:This study aimed at investigating articular cartilage rupture by investigating the response of healthy and degenerate cartilage through altering the osmotic swelling environment of surface-intact, cartilage-on-bone specimens. The osmotic environment in healthy and degenerate bovine cartilage was varied by soaking tiss...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.04.018
更新日期：2011-10-01 00:00:00
abstract：:Although great progresses in the fracture mechanisms and deformation behaviors of cortical bones have been achieved, the effective methods to predict the surface fracture path of cortical bones are still difficult. By using depth-sensing nanoindentation measurement technique, the hardness distribution map of cortical ...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104303
更新日期：2021-01-20 00:00:00
abstract：:The aim of this paper is to propose a biomechanical model that could serve as a tool to overcome some difficulties encountered in experimental studies of the mandible. One of these difficulties is the inaccessibility of the temporomandibular joint (TMJ) and the lateral pterygoid muscle. The focus of this model is to s...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2014.09.022
更新日期：2015-01-01 00:00:00
abstract：:Hydrogels are promising materials for bioengineering applications, and are good model materials for the study of hydrated biological tissues. As these materials often have a structural function, the measurement of their mechanical properties is of fundamental importance. In the present study gelatin gels reinforced wi...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2011.01.009
更新日期：2011-05-01 00:00:00
abstract：:Wood boring is a feature of several insect species and is a major cause of severe and irreparable damage to trees. Adult females typically deposit their eggs on the stem surface under bark scales. The emerging hatchlings live within wood during their larval phase, avoiding possible predation, whilst continually boring...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2020.104027
更新日期：2020-12-01 00:00:00
abstract：:An unusual type of mechanical behavior was registered while studying the swollen hydrogel compositions "cellulose-polyacrylamide" in the conditions of multiple cyclic compression tests with the broad variation of the deformation speed. While increasing the deformation rate the clearly seen inversion of the positions o...
journal_title：Journal of the mechanical behavior of biomedical materials
pub_type： 杂志文章
doi：10.1016/j.jmbbm.2017.03.030
更新日期：2017-07-01 00:00:00
