Abstract：
:This study compared the surface finish of eight different types of aesthetic restorative materials. The materials included resin-modified (Fuji II LC [FL], GC) and highly viscous (Fuji IX GP Fast [FN], GC) glass ionomer cements, a compomer (F2000 [FT], 3M-ESPE), minifilled (Z100 [ZO], 3M-ESPE) and microfilled (A110 [AO], 3M-ESPE) composites and materials based on recently introduced ormocer (Admira [AM], Voco), nanomer (Filtek Supreme Translucent [FST], 3M-ESPE) and nanocluster technology (Filtek Supreme [FS], 3M-ESPE). Sixteen specimens (3-mm long x 3-mm wide x 2-mm deep) of each material were divided into two equal groups. Specimens in Group 1 received no further treatment after polymerization against a matrix strip, while the specimens in Group 2 were roughened with 320 grit grinding paper using a lapping device and were finished/polished with a graded abrasive disk system (Super-Snap, Shofu). The mean roughness (Ra, microm) of materials was determined using a surface profilometry. Data was analyzed by ANOVA/Scheffe's test at significance level 0.05. Mean Ra values ranged from 0.04 to 0.16 microm for Group 1 specimens and 0.15 to 0.68 microm for Group 2 specimens. Results of statistical analysis were as follows: Group 1-FS, FST, FL, FN, AM > FT, AO, ZO; Group 2-FN, FT, FL > AO, FS, ZO, AM, FST (> indicates significantly greater Ra values). For the finished/polished composite materials, Ra values observed for AM and FST were significantly lower than for AO and FS. The surface finish of glass ionomers and compomer was significantly poorer than composites. Composite materials based on ormocer and nanomer technology were significantly smoother than those based on microfillers and nanoclusters.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
Yap AU,Yap SH,Teo CK,Ng JJkeywords:
subject
Has Abstractpub_date
2004-01-01 00:00:00pages
100-4issue
1eissn
0361-7734issn
1559-2863journal_volume
29pub_type
杂志文章abstract：:The purpose of this study was to compare the long-term survivals of two low-copper and three high-copper amalgam alloys, and to analyze four clinical factors for their possible effects on the restoration survivals. Some 1476 polished restorations were placed in hospital patients by a large number of operators and asse...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1991-09-01 00:00:00
abstract：:The antibacterial effects of the dentin bonding systems Syntac, ProBOND, Gluma 3-Step, the resin-modified glass ionomers Photac-Fil, Fuji Lining LC, Fuji II LC, and the polyacid-modified composite resins VariGlass, Geristore, and Infinity were evaluated using the cariogenic bacteria S mutans, L salivarius, S sobrinus,...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1996-11-01 00:00:00
abstract：CLINICAL RELEVANCE:The degree of conversion of contemporary universal adhesives positively correlates with the bond strength to dentin. The correlation is more marked after thermocycling, suggesting that a high degree of conversion is required for long-term dentin bonding durability. SUMMARY:Purpose: The objectives of...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-165-L
更新日期：2020-09-01 00:00:00
abstract：:The aim of the present study was to evaluate the effect of composite resin contamination with powdered and unpowdered latex gloves on the shear bond strength of etch-and-rinse and two-step self-etch adhesive systems. Standard flat dentin surfaces were prepared on the facial aspect of 120 bovine incisors and randomly a...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-088-L
更新日期：2012-09-01 00:00:00
abstract：:Traumatic dental injuries usually occur among children and adolescents, with maxillary central incisors as the most often affected teeth. Complicated crown-root fractures are particularly challenging for esthetic and functional rehabilitation and often require a multidisciplinary approach. A 21-year-old male patient c...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-080-T
更新日期：2016-11-01 00:00:00
abstract：:The aims of this study were to investigate 1) the influence of cleansing methods after saliva contamination and 2) aging conditions (thermocycling and water storage) on zirconia shear bond strength (SBS) with a resin cement. One hundred and eighty zirconia specimens were sandblasted with 50 μm aluminum oxide particles...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-323-L
更新日期：2015-03-01 00:00:00
abstract：:This study investigated the effectiveness of cure and post-gel shrinkage of three visible light-cured composite resins (In Ten-S [IT], Ivoclar Vivadent; Z100 [ZO], 3M-ESPE; Tetric Ceram [TC], Ivoclar Vivadent) when polymerized with a very high intensity (1296 +/- 2 mW/cm2) halogen light (Astralis 10, Ivoclar Vivadent)...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-07-01 00:00:00
abstract：:This study evaluated the two-year clinical performance of two minimally invasive cavity preparation techniques, bur and laser, in Class I occlusal resin composite restorations. Twenty-seven patients, each having at least one pair of occlusal caries, were enrolled in this study. For each patient, one of the cavities wa...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/09-339-C
更新日期：2010-09-01 00:00:00
abstract：:This study evaluated the influence of ceramic thickness and ceramic materials on fracture resistance of posterior partial coverage ceramic restorations. Forty extracted molars were allocated into four groups (n=10) to test for two variables: 1) the thickness of ceramic (1 mm or 2 mm) and 2) the ceramic materials (a li...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/12-459-L
更新日期：2015-03-01 00:00:00
abstract：:This study examined the relationship between the bond agent application duration and the dentin bond strength of several single-application bonding systems. The restorative material/ bonding systems used were Reactmer, with its single-application bonding system Reactmer Bond (RB, Shofu Inc, Kyoto, Japan); Palfique Est...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2002-05-01 00:00:00
abstract：:This study evaluated the shear bond strength of repairs made with a composite (Herculite/Kerr) when two different surface treatment methods and two new generation bond materials were used. The bonding surfaces were prepared by sanding with 500-grit aluminum oxide sandpaper or air abrading with 25-micron aluminum oxide...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-03-01 00:00:00
abstract：:This study investigated the effect of nonrinse conditioners (ie, Ketac Nano Primer [KNP] and GC Self Conditioner [SC]) used as substrate pretreatment and their respective paste-paste resin-modified glass-ionomer cement (RMGIC) (ie, Ketac Nano [KN] and Fuji Filling LC [FF]) on microtensile bond strength to dentin and m...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/14-030-L
更新日期：2015-05-01 00:00:00
abstract：:The aim of this study was to compare five all-in-one bonding agents with respect to microleakage, microtensile bond strength (μTBS), degree of conversion (DC) and the impact of cavity configuration. The materials tested were Adper Easy Bond, Clearfil S3 Bond, iBond, Optibond All-in-One, Xeno IV, and Adper Single Bond ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/14-185-LR1
更新日期：2015-09-01 00:00:00
abstract：:This study investigated the influence of light energy density (intensity x time) on the effectiveness of composite cure in view of the curing profiles of new light-polymerization units. This investigation used a digital microhardness tester to evaluate the hardness of the top/bottom surfaces and hardness ratio of 2 mm...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2001-09-01 00:00:00
abstract：OBJECTIVES:The aim of this study was to compare the two-year clinical performance of three restorative systems in posterior restorations, which included a low-shrinkage composite and both etch-and-rinse and self-etch adhesive strategies. MATERIALS AND METHODS:After signing an informed consent, 25 patients received thr...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/12-364-C
更新日期：2013-11-01 00:00:00
abstract：:Bleaching-induced tooth sensitivity (TS) is highly prevalent. OBJECTIVE:This study aimed to determine if the combination of opioids and nonopioids analgesics (Tylex) may provide a better analgesic effect. METHOD:A triple-blind, parallel, randomized two-center clinical trial was conducted with 105 healthy patients wh...
journal_title：Operative dentistry
pub_type： 杂志文章,多中心研究,随机对照试验
doi：10.2341/17-092-C
更新日期：2018-03-01 00:00:00
abstract：PURPOSE:To investigate the effect of different light exposure times, shades, and thicknesses on the depth of cure (DOC) of bulk fill composites. METHODS AND MATERIALS:Two bulk fill composites, Tetric EvoCeram Bulk Fill (TBF) and Sonic Fill (SF), and a conventional composite, Filtek Supreme Ultra (FSU), were evaluated....
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-057-L
更新日期：2017-09-01 00:00:00
abstract：:Class V restorations are a very common occurrence in clinics. Some reasons include an increase in non-carious cervical lesions (NCCL), root caries and the elderly population. Unfortunately, Class V restorations also represent one of the less durable types of restorations and have a high index of loss of retention, mar...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/09-310-TR
更新日期：2010-05-01 00:00:00
abstract：:This study compared the clinical performance of a polyacid-modified resin composite and a resin-modified glass-ionomer restorative material over two years. Thirty-four pairs of restorations of Compoglass and Fuji II LC were placed in caries-free cervical erosion/abfraction lesions without tooth preparation. Restoratio...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2001-01-01 00:00:00
abstract：:This study investigated the effect of a crown-lengthening ferrule on the fracture resistance of endodontically-treated teeth restored with two dowel-core systems. Thirty-two extracted mandibular first premolars were sectioned perpendicular to the long axis at a point 1.0 mm occlusal to the buccal cementoenamel junctio...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/06-169
更新日期：2007-11-01 00:00:00
abstract：:This study evaluated the in vivo effects of bleaching agents containing 10% carbamide peroxide (Platinum/Colgate) or 7.5% hydrogen peroxide (Day White 2Z/Discus Dental) on mutans Streptococcus during dental bleaching. The products were applied on 30 volunteers who needed dental bleaching. In each volunteer, one of the...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-07-01 00:00:00
abstract：PURPOSE:To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. METHODS AND MATERIALS:Y-TZP ceramic surfaces were ground flat with 600-grit silicon car...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-149-L
更新日期：2015-01-01 00:00:00
abstract：:This in vitro study evaluated the amount of fluoride released from fluoride-containing materials over a period of 28 days. Six disk samples (2.06 +/- 0.06 cm2) were prepared of each material and divided at random into seven groups: Group 1: Chelon-Fil; Group 2: Chelon-Silver; Group 3: VariGlass; Group 4: Dyract; Group...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1996-09-01 00:00:00
abstract：:This in vitro study measured cusp deflection associated with MOD resin composite restorations in maxillary premolars with different curing light modes. Soft-start polymerization may reduce cusp deflection by reducing polymerization shrinkage stress. Forty maxillary premolars were mounted in stone and slot MOD cavities...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：
更新日期：2005-11-01 00:00:00
abstract：OBJECTIVES:To evaluate the efficacy of a new light-cured anesthetic gel for pain control in adults undergoing rubber dam isolation for the restorative treatment of noncarious cervical lesions (NCCLs). METHODS AND MATERIALS:This study was a randomized, split-mouth, triple-blind, controlled trial. The sample comprised 5...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/18-130-C
更新日期：2020-03-01 00:00:00
abstract：:In vitro studies to assess bond strength between resins and ceramics have used surfaces that have been ground flat to ensure standardization; however, in patients, ceramic surfaces are irregular. The effect of a polished and unpolished ceramic on bond strength needs to be investigated. Sixty ceramic specimens (20×5×2 ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-009-L
更新日期：2011-09-01 00:00:00
abstract：:This study investigated the effect of three equivalent radiant exposure energy application sequences (EASs): high intensity power (HIP: 1,177 mW/cm2, 40 seconds), low intensity power (LOP: 573 mW/cm2, 71 seconds) and ramp (RMP: 650 mW/cm2, 5 seconds, then the irradiance increases to 1047 mW/cm2, 37 seconds) on the mic...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/06-30
更新日期：2007-03-01 00:00:00
abstract：:Cracked tooth syndrome is known to occur most frequently in heavily restored teeth. Nevertheless, when the symptoms occur in intact teeth, there is difficulty in obtaining a correct diagnosis because it is difficult for the dentist to find where the crack is located. This clinical report describes the diagnostic proce...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-257
更新日期：2014-09-01 00:00:00
abstract：:Marginal adaptation to cylindrical dentin preparations of five commercially available dental composites--Charisma, Estelite, Herculite, Pertac, and Silux Plus--and seven experimental dental composites containing prepolymerized filler was evaluated by measurement of the wall-to-wall polymerization contraction gaps. The...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1997-11-01 00:00:00
abstract：:Detailed and accurate impressions are made when the oral environment is dry during the impression process. Maintaining a dry field on medically, physically, or emotionally compromised patients can be very challenging. If not achieved, it may compromise dental care and accurate outcomes. This article describes a techni...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-290-T
更新日期：2014-01-01 00:00:00
