Abstract:
:Titanium implants have been used widely and successfully for various types of bone-anchored reconstructions. It is believed that properties of oxide films covering titanium implant surfaces are of crucial importance for a successful osseointegration, in particular at compromized bone sites. The aim of the present study is to investigate the surface properties of anodic oxides formed on commercially pure (c.p.) titanium screw implants as well as to study 'native' oxides on turned c.p. titanium implants. Anodic oxides were prepared by galvanostatic mode in CH3COOH up to the high forming voltage of dielectric breakdown and spark formation. The oxide thicknesses, measured with Auger electron spectroscopy (AES), were in the range of about 200-1000 nm. Barrier and porous structures dominated the surface morphology of the anodic film. Quantitative morphometric analyses of the micropore structures were performed using an image analysis system on scanning electron microscopy (SEM) negatives. The pore sizes were < or = 8 microm in diameter and had 1.27-2.1 microm2 opening area. The porosity was in the range of 12.7-24.4%. The surface roughness was in the range of 0.96-1.03 microm (Sa), measured with TopScan 3D. The crystal structures of the titanium oxide were amorphous, anatase, and a mixtures of anatase and rutile type, as analyzed with thin-film X-ray diffractometry (TF-XRD) and Raman spectroscopy. The chemical compositions consisted mainly of TiO2, characterized with X-ray photoelectron spectroscopy (XPS). The native (thermal) oxide on turned implants was 17.4 nm (+/- 6.2) thick and amorphous. Its chemical composition was TiO2. The surface roughness had an average height deviation of 0.83 microm (Sa). The present results are needed to elucidate the influence of the oxide properties on the biological reaction. The results of animal studies using the presently characterized surface oxides on titanium implants will be published separately.
journal_name
Biomaterialsjournal_title
Biomaterialsauthors
Sul YT,Johansson CB,Petronis S,Krozer A,Jeong Y,Wennerberg A,Albrektsson Tdoi
10.1016/s0142-9612(01)00131-4keywords:
subject
Has Abstractpub_date
2002-01-01 00:00:00pages
491-501issue
2eissn
0142-9612issn
1878-5905pii
S0142-9612(01)00131-4journal_volume
23pub_type
杂志文章相关文献
BIOMATERIALS文献大全abstract::Biomedical device-associated infection is one of the most common and problematic complications faced by millions of patients worldwide. The current antibiotic therapy strategies face challenges, the most serious of which is antibiotic resistance. Studies have shown that the systemic level of interleukin 12 (IL-12) dec...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2009.01.042
更新日期:2009-05-01 00:00:00
abstract::The efficient generation of integration- and xeno-free iPSCs is a prerequisite for their use in clinical applications. Furthermore, non-invasiveness of somatic cell acquisition for iPSC generation is another factor to consider. In this study, we established a practical, simple, and convenient method to generate integr...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2014.05.059
更新日期:2014-09-01 00:00:00
abstract::Fracture healing and fracture fixation in the context of osteoporosis is extremely difficult. To inhibit osteoclast-induced bone resorption and associated implant loosening in this pathology, we describe a local delivery strategy to delivery RNA interfering technology to bone sites to target and down-regulate osteocla...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2012.07.039
更新日期:2012-11-01 00:00:00
abstract::High-density mesenchymal stem cell (MSC) aggregates can be guided to form bone-like tissue via endochondral ossification in vitro when culture media is supplemented with proteins, such as growth factors (GFs), to first guide the formation of a cartilage template, followed by culture with hypertrophic factors. Recent r...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2018.01.006
更新日期:2018-04-01 00:00:00
abstract::We investigated the bioactivity of new chitosan-based multi-membrane hydrogel (MMH) architectures towards chondrocyte-like cells. The microstructure of the hydrogels constituting the membranes precludes any living cell penetration, whereas their lower scale architecture allows the protein diffusion. The biological beh...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2011.04.012
更新日期:2011-08-01 00:00:00
abstract::Thin sheets of nanofibrous (NF) poly(L-lactic acid) (PLLA) matrix were fabricated using a novel phase separation method, mimicking the structure of natural collagen fibers. In this study, the cell morphology, cytoskeleton and adhesion structure, proliferation and differentiation were investigated on NF PLLA matrix usi...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2008.06.015
更新日期:2008-10-01 00:00:00
abstract::Multivalent effect plays an important role in biological processes, particularly in the specific recognition of virus with its host cell during the first step of infection. Here we report the synthesis of multivalent pentacyclic triterpene grafted on cyclodextrin core and potency of against influenza entry activity. N...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2015.11.034
更新日期:2016-02-01 00:00:00
abstract::Neonates with congenital diaphragmatic hernia often require surgical defect closure with a patch. Alternatives to native diaphragmatic tissue are critically needed for this paediatric surgery. The clinical efficacy of mesh patches is limited by complications associated with residual foreign material and by hernia recu...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2018.03.012
更新日期:2018-06-01 00:00:00
abstract::Hepatocytes are anchorage-dependent cells sensitive to microenvironment; the control of the physicochemical properties of the extra-cellular matrices may be useful to the maintenance of hepatocyte functions in vitro for various applications. In a microcapsule-based 3-D hepatocyte culture microenvironment, we could con...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2004.08.017
更新日期:2005-06-01 00:00:00
abstract::Methyl methacrylate (MMA) is a volatile liquid widely used in the manufacture of acrylic polymers. In modern dentistry, MMA is the mainstream material in denture bases. MMA has been implicated as primary irritant and sensitizer, which can cause allergic eczematous reaction on the oral mucosa as well as skin. To date, ...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/s0142-9612(03)00132-7
更新日期:2003-08-01 00:00:00
abstract::Poly(γ-4-((2-(piperidin-1-yl)ethyl)aminomethyl)benzyl-l-glutamate) (PPABLG), a cationic helical polypeptide, has been recently developed by us as an effective non-viral gene delivery vector. In attempts to elucidate the effect of molecular architecture on the gene delivery efficiencies and thereby identify a potential...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2012.11.064
更新日期:2013-03-01 00:00:00
abstract::Chemodynamic therapy (CDT) has recently emerged as a promising treatment for cancer due to the high specificity of CDT towards tumor microenvironment (TME). However, the low efficiency of reactive oxygen species (ROS) generation and the robust ROS defensive mechanisms in cancer cells remain critical hurdles for curren...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2019.119498
更新日期:2019-12-01 00:00:00
abstract::The aim of this study was to develop a chitosan-poly(acrylic) acid based controlled drug release system for gastric antibiotic delivery. Different mixtures of amoxicillin (A), chitosan (CS), and poly(acrylic) acid (PAA) were employed to obtain these polyionic complexes. A non-invasive method was employed for determini...
journal_title:Biomaterials
pub_type: 临床试验,杂志文章
doi:10.1016/s0142-9612(03)00579-9
更新日期:2004-02-01 00:00:00
abstract::A variety of techniques have been applied to generate tissue engineered constructs, where cells are combined with degradable scaffolds followed by a period of in vitro culture or direct implantation. In the current study, a cellularized scaffold was generated by concurrent deposition of electrospun biodegradable elast...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2016.10.029
更新日期:2017-01-01 00:00:00
abstract::Dual-functional liposomes with pH-responsive cell-penetrating peptide (CPP) and active targeting hyaluronic acid (HA) were fabricated for tumor-targeted drug delivery. A series of synthetic tumor pH-triggered CPPs rich in arginines and histidines were screened by comparing tumor cellular uptake efficiency at pH 6.4 wi...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2012.09.027
更新日期:2012-12-01 00:00:00
abstract::Though reduced serum or myoblast co-culture alone can differentiate adipose-derived stem cells (ASCs) into mesenchymal lineages, efficiency is usually not sufficient to restore function in vivo. Often when injected into fibrotic muscle, their differentiation may be misdirected by the now stiffened tissue. Here ASCs ar...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2011.12.004
更新日期:2012-03-01 00:00:00
abstract::Silica nanoparticles are widely used platform materials for the immobilization of proteins to realize applications in biomedicine and biotechnology. We here report on the use of a highly delicate protein for the systematic evaluation of routes for the surface modification of multifunctional silica nanoparticles. To in...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2018.10.035
更新日期:2019-01-01 00:00:00
abstract::Multilayer nanofilms, formed by the layer-by-layer (LbL) adsorption of positively and negatively charged polyelectrolytes, are promising substrates for tissue engineering. We investigate here the attachment and function of hepatic cells on multilayer films in terms of film composition, terminal layer, rigidity, charge...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2008.06.027
更新日期:2008-10-01 00:00:00
abstract::Polyelectrolyte complexes (PEC) were prepared from chitosan as the polycation and several synthesized functional anion polysaccharides, and their effects on cell attachment, morphology, proliferation and differentiation were estimated using normal human osteoblasts (NHOst). After a 1-week incubation, PEC made from pol...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2005.01.041
更新日期:2005-09-01 00:00:00
abstract::Brain tumors and brain metastases are among the deadliest malignancies of all human cancers, largely due to the cellular blood-brain and blood-tumor barriers that limit the delivery of imaging and therapeutic agents from the systemic circulation to tumors. Thus, improved strategies for brain tumor visualization and ta...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2015.07.028
更新日期:2015-10-01 00:00:00
abstract::In vitro protein adsorption, platelet adhesion and activation on new hydrogel surfaces, composed of poly(ethylene oxide) (PEO) and poly(tetramethylene oxide) (PTMO) or poly(dimethyl siloxane) (PDMS), were investigated. By varying PEO length (MW = 2000 or 3400), hydrophobic components (PTMO or PDMS) or polymer topology...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/s0142-9612(01)00306-4
更新日期:2002-04-01 00:00:00
abstract::Bone marrow is the primary hematopoietic organ, which is involved in multiple malignant diseases including acute and chronic leukemia, multiple myeloma, myelodysplastic syndromes, and bone metastases from solid tumors. These malignancies affect normal homeostasis and reshape the bone marrow microenvironment. There are...
journal_title:Biomaterials
pub_type: 杂志文章,评审
doi:10.1016/j.biomaterials.2017.11.029
更新日期:2018-02-01 00:00:00
abstract::Chitosan (CHT)/poly(ɛ-caprolactone) (PCL) blend 3D fiber-mesh scaffolds were studied as possible support structures for articular cartilage tissue (ACT) repair. Micro-fibers were obtained by wet-spinning of three different polymeric solutions: 100:0 (100CHT), 75:25 (75CHT) and 50:50 (50CHT) wt.% CHT/PCL, using a commo...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2010.09.073
更新日期:2011-02-01 00:00:00
abstract::Nanocrystalline diamond (NCD) films and nanoparticulate diamond powder (DP) are the two main representatives of diamond at the nanoscale. This study was designed to investigate the suitability of these biomaterials as cell growth supports and to determine surface characteristic properties best suited to cell attachmen...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2008.07.023
更新日期:2008-11-01 00:00:00
abstract::To develop efficient carriers for inner ear drug delivery, we prepared four kinds of phospholipid-based nanoparticles: neutral, anionic, cationic, and cationic-PEG (polyethyleneglycol) particles. PEG was used to maintain long-term particle circulation in the perilymph, avoiding non-specific binding of particles to pro...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2018.04.038
更新日期:2018-07-01 00:00:00
abstract::Leveraging the multifunctional nature of citrate in chemistry and inspired by its important role in biological tissues, a class of highly versatile and functional citrate-based materials (CBBs) has been developed via facile and cost-effective polycondensation. CBBs exhibiting tunable mechanical properties and degradat...
journal_title:Biomaterials
pub_type: 杂志文章,评审
doi:10.1016/j.biomaterials.2018.05.003
更新日期:2018-09-01 00:00:00
abstract::Hydrogels of crosslinked poly(2-vinylpyridine-1-oxide), PVNO, and poly(2-vinylpyridine-1-oxide)-poly(N-vinyl-pyrrolidone), PNVO-PVP, were synthesized. PVNO hydrogels were found to be degradable in a pseudo-biological medium and their stability could be increased by increasing the relative concentration of the crosslin...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/0142-9612(81)90079-x
更新日期:1981-01-01 00:00:00
abstract::The human heart cannot regenerate after an injury. Lost cardiomyocytes are replaced by scar tissue resulting in reduced cardiac function causing high morbidity and mortality. One possible solution to this problem is cardiac tissue engineering. Here, we have investigated the suitability of non-mulberry silk protein fib...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/j.biomaterials.2011.12.036
更新日期:2012-03-01 00:00:00
abstract::We report here the study of the biocompatibility of a bone graft material, the Pyrost, using a previously established in vitro model of human osteoblasts. The effect of this material on cell proliferation was evaluated by the MTS assay. Results indicated the absolute absence of cytotoxic or cytostatic effect of Pyrost...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/s0142-9612(98)00090-8
更新日期:1998-10-01 00:00:00
abstract::Particulate wear debris of artificial joints, metallic and plastic, and solutions of metals in body fluids are known to have adverse effects. Encapsulation of the articulating parts would prevent wear debris from entering the surrounding tissue and check tissue ingrowth into the joint. The capsule could contain an art...
journal_title:Biomaterials
pub_type: 杂志文章
doi:10.1016/0142-9612(80)90056-3
更新日期:1980-01-01 00:00:00