Combination of Colloidal Silicon Dioxide with Spray-Dried Solid Dispersion to Facilitate Discharge from an Agitated Dryer.

Abstract:

:A feasibility evaluation of the addition of fumed silica (SiO2) into an agitated dryer to aid spray-dried solid dispersion intermediate (SDSDi) flow during secondary drying and discharge is described. The quantity of SiO2 to enhance the flow character of SDSDi was assessed by measuring particle size distribution, bulk density, and flow-through-an-orifice. Results indicate that the addition of the SiO2 did not alter the drying kinetics and did not impact the bulk particle size distribution of the SDSDi. While bulk density of SDSDi increased with the addition of SiO2, the flow, and thus the recovery of the SDSDi-SiO2 batch from the secondary dryer, was significantly higher than that for the intermediate alone. Imaging indicated uniform distribution of SiO2 in the bulk powder and coating on intermediate particles. Premixing and co-sieving of the SiO2 with a portion of pre-dry SDSDi promotes the uniform distribution of SiO2 within the bulk powder bed.

journal_name

AAPS PharmSciTech

journal_title

AAPS PharmSciTech

authors

Lee YC,McNevin M,Ikeda C,Chouzouri G,Moser J,Harris D,Howell L

doi

10.1208/s12249-019-1392-1

subject

Has Abstract

pub_date

2019-05-03 00:00:00

pages

182

issue

5

issn

1530-9932

pii

10.1208/s12249-019-1392-1

journal_volume

20

pub_type

杂志文章
  • Data-Driven Modeling of the Bicalutamide Dissolution from Powder Systems.

    abstract::Low solubility of active pharmaceutical compounds (APIs) remains an important challenge in dosage form development process. In the manuscript, empirical models were developed and analyzed in order to predict dissolution of bicalutamide (BCL) from solid dispersion with various carriers. BCL was chosen as an example of ...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-020-01660-w

    authors: Mendyk A,Pacławski A,Szafraniec-Szczęsny J,Antosik A,Jamróz W,Paluch M,Jachowicz R

    更新日期:2020-03-31 00:00:00

  • In Vivo Anticancer Efficacy and Toxicity Studies of a Novel Polymer Conjugate N-Acetyl Glucosamine (NAG)-PEG-Doxorubicin for Targeted Cancer Therapy.

    abstract::A novel polymer-drug conjugate, polyethylene glycol-N-(acetyl)-glucosamine-doxorubicin (PEG-NAG-DOX) was evaluated in this study for its in vivo potential for treatment of tumours demonstrating improved efficacy and reduced toxicity. The proposed polymer-drug conjugate comprised of polyethylene glycol-maleimide (mPEG-...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-017-0787-0

    authors: Pawar S,Mahajan K,Vavia P

    更新日期:2017-11-01 00:00:00

  • Formulation and optimization of nonionic surfactants emulsified nimesulide-loaded PLGA-based nanoparticles by design of experiments.

    abstract::This investigation aimed to develop nimesulide (NMS)-loaded poly(lactic-co-glycolic acid) (PLGA)-based nanoparticulate formulations as a biodegradable polymeric drug carrier to treat rheumatoid arthritis. Polymeric nanoparticles (NPs) were prepared with two different nonionic surfactants, vitamin E d-α-tocopheryl poly...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-013-0048-9

    authors: Turk CT,Oz UC,Serim TM,Hascicek C

    更新日期:2014-02-01 00:00:00

  • Particle size and temperature effect on the physical stability of PLGA nanospheres and microspheres containing Bodipy.

    abstract::The purpose of this study was to investigate the effect of particle size, storage temperature, and duration of storage on the physical stability and morphology of polylactic-co-glycolic acid (PLGA) nanospheres and microspheres. PLGA nanospheres and microspheres containing the fluorescent dye, Bodipy, were prepared in ...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt050453

    authors: De S,Robinson DH

    更新日期:2004-09-13 00:00:00

  • 3D-Printed Isoniazid Tablets for the Treatment and Prevention of Tuberculosis-Personalized Dosing and Drug Release.

    abstract::The aim of the present work was to produce 3D-printed oral dosage forms with a sufficient drug dose displaying various release profiles. Hot-melt extrusion was utilized to produce drug-loaded feedstock material that was subsequently 3D-printed into 6, 8, and 10 × 2.5 mm tablets with 15% and 90% infill levels. The prep...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-018-1233-7

    authors: Öblom H,Zhang J,Pimparade M,Speer I,Preis M,Repka M,Sandler N

    更新日期:2019-01-07 00:00:00

  • Development, optimization, and characterization of solid self-nanoemulsifying drug delivery systems of valsartan using porous carriers.

    abstract::The present studies entail formulation development of novel solid self-nanoemulsifying drug delivery systems (S-SNEDDS) of valsartan with improved oral bioavailability, and evaluation of their in vitro and in vivo performance. Preliminary solubility studies were carried out and pseudoternary phase diagrams were constr...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-012-9865-5

    authors: Beg S,Swain S,Singh HP,Patra ChN,Rao ME

    更新日期:2012-12-01 00:00:00

  • Solubilization of cyclosporin A.

    abstract::This study investigated the solubilization of cyclosporin A (CsA), a neutral undecapeptide, by cosolvency, micellization, and complexation. Cosolvents (ethanol, propylene glycol, polyethylene glycol, tetrahydrofurfuryl alcohol polyethyleneglycol ether, and glycerin), surfactants (polyoxyethylene sorbitan monooleate [(...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt020102

    authors: Ran Y,Zhao L,Xu Q,Yalkowsky SH

    更新日期:2001-01-18 00:00:00

  • Direct pelletization in a rotary processor controlled by torque measurements. III. Investigation of microcrystalline cellulose and lactose grade.

    abstract::The aim of the present study was to investigate the use of different grades of microcrystalline cellulose (MCC) and lactose in a direct pelletization process in a rotary processor. For this purpose, a mixed 2- and 3-level factorial study was performed to determine the influence of the particle size of microcrystalline...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt060362

    authors: Kristensen J

    更新日期:2005-10-24 00:00:00

  • Graphical comparison of image analysis and laser diffraction particle size analysis data obtained from the measurements of nonspherical particle systems.

    abstract::The purpose of this paper is to describe results from the use of a set of Excel macros written to facilitate the comparison of image analysis (IA) and laser diffraction (LD) particle size analysis (psa) data. Measurements were made on particle systems of differing morphological characteristics including differing aver...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt070369

    authors: Kelly RN,DiSante KJ,Stranzl E,Kazanjian JA,Bowen P,Matsuyama T,Gabas N

    更新日期:2006-08-18 00:00:00

  • Research Progress of Drug Treatment in Novel Coronavirus Pneumonia.

    abstract::As of March 10, 2020, more than 100,000 novel coronavirus pneumonia cases have been confirmed globally. With the continuous spread of the new coronavirus pneumonia epidemic in even the world, prevention and treatment of the disease have become urgent tasks. The drugs currently being developed are not adequate to deal ...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章,评审

    doi:10.1208/s12249-020-01679-z

    authors: Yan J,Liu A,Huang J,Wu J,Fan H

    更新日期:2020-05-13 00:00:00

  • The influence of modified pluronic F127 copolymers with higher phase transition temperature on arsenic trioxide-releasing properties and toxicity in a subcutaneous model of rats.

    abstract::Pluronic F127 (PF-127) shows thermoreversible property, which is of the utmost interest in optimizing drug formulation and delivery. However, its hitherto unresolved drawback of a low phase transition temperature (T (tr)) has limited its application in injectable drug delivery systems. We have ...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-012-9756-9

    authors: Ma Y,Zhang C,Chen X,Jiang H,Pan S,Easteal AJ,Sun X

    更新日期:2012-06-01 00:00:00

  • Topical Niosome Gel of Zingiber cassumunar Roxb. Extract for Anti-inflammatory Activity Enhanced Skin Permeation and Stability of Compound D.

    abstract::An extract of Zingiber cassumunar Roxb. (ZC) was encapsulated in niosomes of which a topical gel was formed. (E)-4-(3',4'-dimethoxyphenyl)but-3-en-1-ol or compound D detected by a gradient HPLC was employed as the marker and its degradation determined to follow zero-order kinetics. Niosomes significantly retarded ther...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-015-0376-z

    authors: Priprem A,Janpim K,Nualkaew S,Mahakunakorn P

    更新日期:2016-06-01 00:00:00

  • Measurement of fluid viscosity at microliter volumes using quartz impedance analysis.

    abstract::The purpose of this work was to measure viscosity of fluids at low microliter volumes by means of quartz crystal impedance analysis. To achieve this, a novel setup was designed that allowed for measurement of viscosity at volumes of 8 to 10 microL. The technique was based on the principle of electromechanical coupling...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt050347

    authors: Saluja A,Kalonia DS

    更新日期:2004-08-05 00:00:00

  • Evaluation of the performance characteristics of bilayer tablets: Part II. Impact of environmental conditions on the strength of bilayer tablets.

    abstract::Ambient air humidity and temperature are known to influence the mechanical strength of tablets. The objective of this work is to understand the influence of processing parameters and environmental conditions (humidity and temperature) on the strength of bilayer tablets. As part of this study, bilayer tablets were comp...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-012-9846-8

    authors: Kottala N,Abebe A,Sprockel O,Bergum J,Nikfar F,Cuitiño AM

    更新日期:2012-12-01 00:00:00

  • An investigation into the influence of experimental conditions on in vitro drug release from immediate-release tablets of levothyroxine sodium and its relation to oral bioavailability.

    abstract::The aim of this study was to investigate the influence of experimental conditions on levothyroxine sodium release from two immediate-release tablet formulations which narrowly passed the standard requirements for bioequivalence studies. The in vivo study was conducted as randomised, single-dose, two-way cross-over pha...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-011-9660-8

    authors: Kocic I,Homsek I,Dacevic M,Parojcic J,Miljkovic B

    更新日期:2011-09-01 00:00:00

  • Investigation of Effect of Isopropyl Palmitate on Drug Release from Transdermal Patch and Molecular Dynamics Study.

    abstract::Chemical penetration enhancers are widely used in transdermal drug delivery system. However, few studies have focused on changes of concentration in chemical penetration enhancers. In this study, the effect of concentrations of enhancers on drug release and its mechanism were investigated. Zolmitriptan (ZOL) was used ...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-019-1370-7

    authors: Ruan J,Wan X,Quan P,Liu C,Fang L

    更新日期:2019-04-25 00:00:00

  • Probucol release from novel multicompartmental microcapsules for the oral targeted delivery in type 2 diabetes.

    abstract::In previous studies, we developed and characterised multicompartmental microcapsules as a platform for the targeted oral delivery of lipophilic drugs in type 2 diabetes (T2D). We also designed a new microencapsulated formulation of probucol-sodium alginate (PB-SA), with good structural properties and excipient compati...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-014-0205-9

    authors: Mooranian A,Negrulj R,Al-Sallami HS,Fang Z,Mikov M,Golocorbin-Kon S,Fakhoury M,Watts GF,Matthews V,Arfuso F,Lambros A,Al-Salami H

    更新日期:2015-02-01 00:00:00

  • Mathematical modeling of an aqueous film coating process in a Bohle Lab-Coater: part 2: application of the model.

    abstract::For the prediction of the air and product temperatures, the product moisture, and the air humidity during a coating process in a Bohle Lab-Coater, a model was developed. The purpose of this work was to determine the limit moisture, the critical moisture, and the constant for the exchange rate between both zones and to...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt070243

    authors: Page S,Baumann KH,Kleinebudde P

    更新日期:2006-05-05 00:00:00

  • Paul B. Myrdal, Ph.D. (June 25, 1967-May 19, 2018).

    abstract:: ...

    journal_title:AAPS PharmSciTech

    pub_type: 传,历史文章,新闻

    doi:10.1208/s12249-018-1106-0

    authors: Williams ROB 3rd

    更新日期:2018-08-01 00:00:00

  • Investigating the parameters affecting the stability of superparamagnetic iron oxide-loaded nanoemulsion using artificial neural networks.

    abstract::Nanoemulsions are increasingly being investigated for their fascinating capability of loading both hydrophobic and hydrophilic molecules while their stability is still an issue, being affected by various factors. In this study, to evaluate the dominant factors affecting the stability of nanoemulsions, artificial neura...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-012-9864-6

    authors: Ahmadi Lakalayeh G,Faridi-Majidi R,Saber R,Partoazar A,Mehr SE,Amani A

    更新日期:2012-12-01 00:00:00

  • A new approach for increasing ascorbyl palmitate stability by addition of non-irritant co-antioxidant.

    abstract::The aim of this work was to test innovative approach for enhancing ascorbyl palmitate stability in microemulsions for topical application by addition of newly synthesized co-antioxidant 4-(tridecyloxy)benzaldehyde oxime (TDBO) and to investigate its antioxidant activity and finally to evaluate cytotoxicity of TDBO-loa...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-010-9507-8

    authors: Gosenca M,Obreza A,Pečar S,Gašperlin M

    更新日期:2010-09-01 00:00:00

  • Considerations in developing a target product profile for parenteral pharmaceutical products.

    abstract::A target product profile (TPP) describes how a product will be utilized by the end user. A systematically developed TPP can ensure alignment of objectives across company departments, accelerate development timelines, minimize development risks, and eventually lead to an optimal product. A TPP is particularly important...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章,评审

    doi:10.1208/s12249-010-9521-x

    authors: Lambert WJ

    更新日期:2010-09-01 00:00:00

  • Preparation and characterization of co-grinded mixtures of aceclofenac and neusilin US2 for dissolution enhancement of aceclofenac.

    abstract::The present study was carried out with a view to enhance the dissolution of poorly water-soluble BCS-class II drug aceclofenac by co-grinding with novel porous carrier Neusilin US(2.) (amorphous microporous granules of magnesium aluminosilicate, Fuji Chemical Industry, Toyama, Japan). Neusilin US(2) has been used as a...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-009-9221-6

    authors: Vadher AH,Parikh JR,Parikh RH,Solanki AB

    更新日期:2009-01-01 00:00:00

  • Development of acid-resistant alginate/trimethyl chitosan nanoparticles containing cationic β-cyclodextrin polymers for insulin oral delivery.

    abstract::In this study, the use of trimethylchitosan (TMC), by higher solubility in comparison with chitosan, in alginate/chitosan nanoparticles containing cationic β-cyclodextrin polymers (CPβCDs) has been studied, with the aim of increasing insulin uptake by nanoparticles. Firstly, TMCs were synthesized by iodomethane, and C...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-014-0282-9

    authors: Mansourpour M,Mahjub R,Amini M,Ostad SN,Shamsa ES,Rafiee-Tehrani M,Dorkoosh FA

    更新日期:2015-08-01 00:00:00

  • Design and Characterization of Metformin-Loaded Solid Lipid Nanoparticles for Colon Cancer.

    abstract::Colorectal cancer is a global concern, and its treatment is fraught with non-selective effects including adverse side effects requiring hospital visits and palliative care. A relatively safe drug formulated in a bioavailability enhancing and targeting delivery platform will be of significance. Metformin-loaded solid l...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-016-0505-3

    authors: Ngwuluka NC,Kotak DJ,Devarajan PV

    更新日期:2017-02-01 00:00:00

  • Improved Oral Pharmacokinetics of Pentoxifylline with Palm Oil and Capmul® MCM Containing Self-Nano-Emulsifying Drug Delivery System.

    abstract::Pentoxifylline (PTX), an anti-hemorrhage drug used in the treatment of intermittent claudication, is extensively metabolized by the liver resulting in a reduction of the therapeutic levels within a short duration of time. Self-nano-emulsifying drug delivery system (SNEDDS) is well reported to enhance the bio-absorptio...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-020-01644-w

    authors: Shailendrakumar AM,Ghate VM,Kinra M,Lewis SA

    更新日期:2020-04-21 00:00:00

  • Effects of the Preparation Process on the Properties of Amorphous Solid Dispersions.

    abstract::The use of amorphous solid dispersions to improve the bioavailability of active ingredients from the BCS II and IV classifications continues to gain interest in the pharmaceutical industry. Over the last decade, methods for generating amorphous solid dispersions have been well established in commercially available pro...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章,评审

    doi:10.1208/s12249-017-0861-7

    authors: Huang S,Williams RO 3rd

    更新日期:2018-07-01 00:00:00

  • Synthesis, Formulation, and Characterization of Doxorubicin-Loaded Laponite/Oligomeric Hyaluronic Acid-Aminophenylboronic Acid Nanohybrids and Cytological Evaluation against MCF-7 Breast Cancer Cells.

    abstract::As a synthetic clay material, laponite RDS (LR) was investigated as an effective drug carrier as a result of the special nanodisk structure together with the negative-charged surface to achieve enhanced cellular uptake and targeted delivery. In this research work, the synthesized oligomeric hyaluronic acid-aminophenyl...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-019-1533-6

    authors: Yang Y,Li J,Chen F,Qiao S,Li Y,Pan W

    更新日期:2019-11-20 00:00:00

  • A novel fiber-optic photometer for in situ stability assessment of concentrated oil-in-water emulsions.

    abstract::The purpose of this research was to evaluate a novel fiber-optic photometer for its ability to monitor physical instabilities occurring in concentrated emulsions during storage. For this, the fiber-optic photometer was used to measure transmission of oil-in-water emulsions stabilized with hypromellose (HPMC) as a func...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/pt0803070

    authors: Oliczewski S,Daniels R

    更新日期:2007-08-31 00:00:00

  • Behavior of freezable bound water in the bacterial cellulose produced by Acetobacter xylinum: an approach using thermoporosimetry.

    abstract::The aim of the study is to examine thermal behavior of water within reticulated structure of bacterial cellulose (BC) films by sub-ambient differential scanning calorimetry (DSC). BC films with different carbon source, either manitol (BC (a)) or glycerol (BC (b)), were produced by Acetobacter xylinum using Hestrin and...

    journal_title:AAPS PharmSciTech

    pub_type: 杂志文章

    doi:10.1208/s12249-008-9104-2

    authors: Kaewnopparat S,Sansernluk K,Faroongsarng D

    更新日期:2008-01-01 00:00:00