Abstract：
:A new type of optical fiber hydrophone is constructed with a fiber Bragg grating (FBG) based on the intensity modulation of laser light in an FBG under the influence of sound pressure. The FBG hydrophone shows linearity, with dynamic range about 70 dB. It can measure amplitude and phase of an acoustic field in real time, and operates in a wide range of acoustic frequency, at least from 1 kHz to 3 MHz. No signal distortion is observed in the detected signal. Because of the simplicity in its operating principle and geometry, an FBG hydrophone is expected to be an acoustic sensor of high practicality compared to a conventional optical fiber hydrophone.
journal_name
Ultrasonicsjournal_title
Ultrasonicsauthors
Takahashi N,Yoshimura K,Takahashi S,Imamura Kdoi
10.1016/s0041-624x(99)00105-5subject
Has Abstractpub_date
2000-03-01 00:00:00pages
581-5issue
1-8eissn
0041-624Xissn
1874-9968pii
S0041-624X(99)00105-5journal_volume
38pub_type
杂志文章相关文献
ULTRASONICS文献大全abstract：:The objective of this study was to examine the potential of ultrasonic velocity as a rapid and nondestructive method to predict the dimensional stability of oak (Quercus petraea (Mattuschka) Lieblein) and chestnut (Castanea sativa Mill.) that are commonly used in flooring industry. Ultrasonic velocity, specific gravit...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2015.11.007
更新日期：2016-03-01 00:00:00
abstract：:The mechanical pre-stress applied in piezotransducers used to generate high power ultrasound is needed to avoid ceramics fracture on traction cycle. Pre-stress levels inferior to 50 MPa can yield resonance shifting due to effectiveness of acoustic coupling between transducer pieces. Symmetrical transducers with differ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(03)00096-9
更新日期：2003-05-01 00:00:00
abstract：PURPOSE:Human 8-oxoguanine DNA glycosylase (OGG1) is a major base excision repair enzyme, and it was reported to suppress the activation of intrinsic apoptotic signaling pathway in response to oxidative stress. In this study, our aim was to investigate the effects of OGG1 downregulation on ultrasound-induced apoptosis ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.07.005
更新日期：2016-12-01 00:00:00
abstract：:This paper deals with 2-D simulation of finite-amplitude standing waves behavior in rectangular acoustic resonators. Set of three partial differential equations in third approximation formulated in conservative form is derived from fundamental equations of gas dynamics. These equations form a closed set for two compon...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.05.008
更新日期：2006-12-22 00:00:00
abstract：:The purpose of this study is to gain the knowledge and experience in the design of thin-disk piezoceramic-driving ultrasonic actuator dedicated. In this paper, the design and construction of an innovative ultrasonic actuator is developed as a stator, which is a composite structure consisting of piezoceramic (PZT) memb...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(03)00128-8
更新日期：2003-08-01 00:00:00
abstract：:Ultrasonic vibration cutting is an efficient cutting process for mechanical micro-machining. This process can generate intricate surface textures with different geometric characteristics. Micro-grooves/micro-channels are among the most frequently encountered micro-structures and, as such, are the focus of this paper. ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2015.12.016
更新日期：2016-04-01 00:00:00
abstract：:Electromagnetic-acoustic transducers (EMATs) consist of a magnet and a coil. They are advantageous in some non-destructive evaluation (NDE) applications because no direct contact with the specimen is needed to send and receive ultrasonic waves. However, EMATs commonly require excitation peak powers greater than 1kW an...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.02.009
更新日期：2017-07-01 00:00:00
abstract：:Fundamental understanding of ultrasound interaction with material discontinuities having closed interfaces has many engineering applications such as nondestructive evaluation of defects like kissing bonds and cracks in critical structural and mechanical components. In this paper, to analyze the acoustic field nonlinea...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.12.007
更新日期：2018-03-01 00:00:00
abstract：:A practical optodynamic study was performed to determine the usability of different lengths of laser pulses for the generation of ultrasonic transients in a solid material. The aim of the study was to evaluate the possibility of a dual use for a laser pulse-for laser material processing, on the one hand, and for the u...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.05.071
更新日期：2006-12-22 00:00:00
abstract：:Guided acoustic waves, such as Lamb waves, are widely applied for material characterization, sensing of liquids and the generation of streaming in liquids. There are numerical simulation tools for the prediction of their propagation near a solid-liquid boundary but a demand for complementary measurement techniques for...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.105955
更新日期：2019-11-01 00:00:00
abstract：:A reformulation of the Thomson-Haskell method is presented for calculating the reflection coefficients of multilayer structure immersing in the coupling fluid. Instead of directly multiplying the layer propagator matrix, the new method splits the layer propagator matrix and excursively determines the interface stiffne...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2012.08.004
更新日期：2012-12-01 00:00:00
abstract：:In cancellous bone, longitudinal waves often separate into fast and slow waves depending on the alignment of bone trabeculae in the propagation path. This interesting phenomenon becomes an effective tool for the diagnosis of osteoporosis because wave propagation behavior depends on the bone structure. Since the fast w...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2008.04.011
更新日期：2008-11-01 00:00:00
abstract：:Ultrasonic insertion technique (IT) is an ultrasonic technique which involves sample immersion in a solution to determine its acoustic properties. IT is normally used to determine the acoustic properties of a medical phantom. We proposed the use of IT as an alternative technique to the common contact ultrasonic techni...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.11.025
更新日期：2017-03-01 00:00:00
abstract：:In order to guide the needle to the correct location in 3D US-guided brachytherapy, the needle is continuously tracked as it is being inserted. A pre-scan before the needle insertion and a post-scan after the needle insertion are subtracted to obtain a difference image containing the needle. The image is projected alo...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.07.003
更新日期：2006-12-22 00:00:00
abstract：:In acoustic and ultrasonic non-destructive testing techniques, it is sometimes beneficial to concentrate sound energy at a chosen location in space and at a specific instance in time, for example to improve the signal-to-noise ratio or activate the nonlinearity of damage features. Time Reversal (TR) techniques, taking...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.01.010
更新日期：2016-04-01 00:00:00
abstract：:This paper deals with the influence of acousto-optic interactions on the displacement measurements performed over transducer array and their effects on the predicted diffraction field. Changes on the temporal/spatial responses and the plane wave decomposition of the displacement are discussed. Modifications made on th...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2003.12.035
更新日期：2004-04-01 00:00:00
abstract：:The main challenge faced by 3D ultrasonic imaging with 2D array transducers is the large number of elements required to achieve an acceptable level of quality in the images. Therefore, the optimisation of the array layout, in order to reduce the number of active elements in the aperture, has been a research topic in t...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.09.010
更新日期：2010-02-01 00:00:00
abstract：:An improved method for ultrasonic location of multiple flaws using perpendicular ultrasonic arrays, working in near-field conditions, is presented. The method uses the pulse-echo technique and is based on the processing of the information acquired by both the elemental emitting transducers and their adjacent ones. Thi...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.05.107
更新日期：2006-12-22 00:00:00
abstract：:The numerical studies conducted in this paper are based on our previous research (Chen et al., 2017); through use of the spectral element method, parametric sensitivity studies of Nonlinear Coda Wave Interferometry (NCWI) are established here and divided into two parts. In the first part, CWI observables are found to ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.105968
更新日期：2019-11-01 00:00:00
abstract：:In this paper, an improved touch probe sensor device for higher sensitivity and low contact force is reported. In order to improve the resolution, we have evaluated the sensitivity and fabricated a miniaturized sensor. The sensor transducer was 3 mm long and had higher resonance frequency. The resonance frequency of t...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(02)00091-4
更新日期：2002-05-01 00:00:00
abstract：:We experimentally demonstrate a very large ultrasonic band gap in a one-dimensional phononic crystal. The structure consists of periodic tungsten pillars fixed to a tailored silicon strip with a layer of epoxy. Combining local resonances and Bragg scattering, the gap ranges from 450kHz to 1250kHz, which corresponds to...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.03.003
更新日期：2017-07-01 00:00:00
abstract：:A method for fabricating disposable membrane hydrophones is presented. The disposable hydrophones are intended for onetime use in such damaging environments as chemically contaminating fluids and high-amplitude (peak amplitude ∼100MPa) shock wave fields, where the use of commercial membrane hydrophones is not recommen...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.05.016
更新日期：2017-11-01 00:00:00
abstract：:Knowing the low-frequency response of hydrophones, down to 100 kHz at least, is important for accurate biomedical ultrasound measurements. However, current international standards do not extend below 500 kHz. Furthermore, commercial hydrophone sources typically do not supply sensitivity data below 1-2 MHz. Therefore, ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2003.12.008
更新日期：2004-04-01 00:00:00
abstract：:Ultrasonic vibration has been observed to lower the flow stress necessary to initiate plastic deformation, a phenomenon known as "acoustic softening". This unique effect of ultrasound has been extensively applied in welding, machining, forming of metals, and ultrasonic additive manufacturing to lower the yield stress ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.106005
更新日期：2020-03-01 00:00:00
abstract：:The propagation of ultrasound through an austenitic weld is investigated experimentally as well as in a numerical simulation. The weld is insonified at normal incidence to the fusion line with a longitudinal contact transducer. In order to experimentally trace the ultrasound through the weld, slices of different thick...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(99)00103-1
更新日期：2000-03-01 00:00:00
abstract：:The linear wave equation in a lossless medium is time reversible, i.e., every solution p(x, t) has a temporal mirror solution p(x, -t). Analysis shows that time reversal also holds for the lossless nonlinear wave equation. In both cases, time-reversal invariance is violated when losses are present. For nonlinear propa...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/s0041-624x(00)00020-2
更新日期：2000-09-01 00:00:00
abstract：:We studied thickness-shear and thickness-twist vibrations of a monolithic, two-pole crystal filter made from a plate of AT-cut quartz. The scalar differential equations derived by Tiersten and Smythe for electroded and unelectroded quartz plates were employed which are valid for both the fundamental and the overtone m...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2015.01.003
更新日期：2015-04-01 00:00:00
abstract：:In the food industry, ultrasonic cutting is used to improve separation by a reduction of the cutting force. This reduction can be attributed to the modification of tool-workpiece interactions at the cutting edge and along the tool flanks because of the superposition of the cutting movement with ultrasonic vibration of...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.03.001
更新日期：2009-06-01 00:00:00
abstract：:Broken wires often occur at multiple locations in the same wire of a strand due to the recovery length, which is defined as the length of the wire taking up its full share of the axial load from the break point. The detection of broken-wire flaws at multiple locations along the same wire is investigated using guided w...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2012.05.003
更新日期：2013-01-01 00:00:00
abstract：:Cones and wedges inserted between an ultrasonic transducer and the specimen provide the transducer (circular or rectangular shape) with enhanced capability for point or line contact with the specimen. Such an arrangement is useful in that the transducer can be used for transmitting to and receiving from a point (or li...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2004.10.002
更新日期：2005-03-01 00:00:00
