Abstract：
:This paper presents the results of the theoretical and 2D FEM modeling excitation and detection of evanescent acoustic waves in piezoelectric plates. By application of 2D ordinary differential equations derived by Auld, we obtained the dispersion curves of A1 and SH1 waves in YX LiNbO3 and YX KNbO3 plates in proximity to a zero group velocity point. The branches corresponding to evanescent acoustic waves are distinguished. A frequency range where real part of evanescent wave velocity is more than imaginary one was found. In this region evanescent mode is characterized by opposite directions of the phase and group velocities, i.e. this is backward wave. The theoretical analysis was verified in commercial 2D FEM software COMSOL 5.3. By modeling a set of interdigital transducers placed on the surface of Y-cut LiNbO3 wafer with various values of the spatial period we found the resonant frequencies corresponding to evanescent A1 mode. Due to proximity of this wave to a zero group velocity point its properties should be extremely sensitive to change of waveguide quality and ambient air. This is open the possibility to use these waves for development of high sensitive sensors and for nondestructive waveguide analysis.
journal_name
Ultrasonicsjournal_title
Ultrasonicsauthors
Kuznetsova I,Nedospasov I,Smirnov A,Qian ZH,Wang B,Dai XYdoi
10.1016/j.ultras.2019.105961subject
Has Abstractpub_date
2019-11-01 00:00:00pages
105961eissn
0041-624Xissn
1874-9968pii
S0041-624X(19)30178-7journal_volume
99pub_type
杂志文章相关文献
ULTRASONICS文献大全abstract：:In this study, 3D finite element simulation of ultrasonically-assisted drilling is carried out to analyze the effect of ultrasonic vibrations on common difficulties existed in conventional drilling. Influence of harmonic movement of drill bit on the formation of built-up edge is experimentally evaluated and also discu...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.11.009
更新日期：2017-03-01 00:00:00
abstract：:In ultrasonic non-destructive testing of materials with a coarse-grained structure the scattering from the grains causes backscattering noise, which masks flaw echoes in the measured signal. Several filtering methods have been proposed for improving the signal-to-noise ratio. In this paper we present a comparative stu...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2009.05.010
更新日期：2009-12-01 00:00:00
abstract：:This paper is concerned with the probing of the transversal envelope solitons propagation in circular waveguides when a set of requirements (non-linearity and dispersion) are fulfilled in the waveguide and balanced. The basic idea is to analyze the shape of an acoustic pulse after it has traveled one or few trips thro...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.01.016
更新日期：2014-07-01 00:00:00
abstract：:Ultrasonic studies of the group of halogens of benzene and particularly dependence of acoustic parameters on the structure of organic liquids, demonstrate some interesting regularities in the group of these compounds in gas and liquid states. In this paper results for five cyclic liquids: bromo-, chloro-, fluoro- and ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.05.146
更新日期：2006-12-22 00:00:00
abstract：:Although ultrasonic energy is widely used cleaning and degreasing of parts and assemblies in automotive and other industries, the use of ultrasonic energy in an industrial scale for textile washing is very new. This is due to the complexity of controlling the combination of chemical and mechanical effects, whereas wit...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2004.02.005
更新日期：2004-04-01 00:00:00
abstract：:We experimentally demonstrate a very large ultrasonic band gap in a one-dimensional phononic crystal. The structure consists of periodic tungsten pillars fixed to a tailored silicon strip with a layer of epoxy. Combining local resonances and Bragg scattering, the gap ranges from 450kHz to 1250kHz, which corresponds to...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.03.003
更新日期：2017-07-01 00:00:00
abstract：:In general, the design and analysis of ultrasonic motor and motor's control strategy are based on mathematical model. The academic model is widely used in the analysis of traveling wave ultrasonic motor (TWUSM). But the dispersive characteristic of piezoelectric ceramics and other complicated process, such as the fric...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2013.09.012
更新日期：2014-02-01 00:00:00
abstract：:In this paper, we investigated theoretically and experimentally the effect of the conductivity of the film located in the immediate vicinity of the free side of a piezoelectric resonator based on the PZT ceramics on its characteristics. It is shown that with increasing the conductivity of the film at first the paralle...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2018.09.016
更新日期：2019-04-01 00:00:00
abstract：:The Lamb waves are used for the ultrasonic characterization of welds because of their relative long-range propagation. In this paper, a simplified model of a weld-strip between two identical semi-infinite elastic layers is investigated. The reflected and transmitted ultrasonic fields are expressed by modal series whos...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2004.11.004
更新日期：2005-06-01 00:00:00
abstract：:The paper presents the characteristics of vertically polarized surface waves generated in silicon substrate by acoustic coupling of bulk waves excited in a periodically patterned ZnO film on silicon. The finite element simulations are performed on the proposed patterned-ZnO/Si structure and vertically polarized modes ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2015.01.008
更新日期：2015-05-01 00:00:00
abstract：:Ultrasonic vibration cutting is an efficient cutting process for mechanical micro-machining. This process can generate intricate surface textures with different geometric characteristics. Micro-grooves/micro-channels are among the most frequently encountered micro-structures and, as such, are the focus of this paper. ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2015.12.016
更新日期：2016-04-01 00:00:00
abstract：:We develop a new ultrasonic imaging framework for non-destructive testing of an immersed specimen featuring an irregular top surface and demonstrate its capability of accurately depicting the lower surfaces of multiple damages hidden in the specimen. Central to the framework is a multistep angular spectrum approach (A...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2020.106233
更新日期：2020-12-01 00:00:00
abstract：:The radial variations in the velocity of longitudinal waves propagating through Japanese cedar and Japanese cypress were experimentally investigated. In addition, the tracheid length (TL), microfibril angle (MFA), air-dried density (AD), and moisture content (MC) were measured in order to determine the effect of wood ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2010.10.001
更新日期：2011-04-01 00:00:00
abstract：:The present study investigated the accuracy of micro-scale finite element modeling for simulating broadband ultrasound propagation in water-saturated trabecular bone-mimicking phantoms. To this end, five commercially manufactured aluminum foam samples as trabecular bone-mimicking phantoms were utilized for ultrasonic ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.01.014
更新日期：2016-05-01 00:00:00
abstract：:Laser ultrasonic is a most promising method for non-destructive evaluation of residual stress. The residual stress of thin steel plate is measured by laser ultrasonic technique. The pre-stress loading device is designed which can easily realize the condition of the specimen being laser ultrasonic tested at the same ti...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.08.013
更新日期：2017-01-01 00:00:00
abstract：:The characterization of brain tissue is crucial to better understand neurological disorders. Mechanical characterization is an emerging tool in that field. The purpose of this work was to validate a transient ultrasound technique aimed at measuring dispersion of mechanical parameters of the brain tissue. The first par...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2017.10.009
更新日期：2018-03-01 00:00:00
abstract：:The T-matrix approach is used to calculate the scattering of sound waves by an ellipsoidal void in a fluid. Results are presented for the total cross-section of a sphere as a function of frequency; this is related to the detection of the onset of bends in divers. Results are also presented for the angular variation in...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(83)90073-2
更新日期：1983-07-01 00:00:00
abstract：:Increased stiffness of the arteries has recently gained acceptance as a potential risk for cardiovascular and many other diseases. Pulse wave velocity (PWV) is widely used for estimating the stiffness of an artery. However, PWV is an indicator of average artery stiffness between two measuring points. In addition to me...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.06.054
更新日期：2006-12-22 00:00:00
abstract：:An ultrasonic technique for imaging nonlinear scatterers, such as partially-closed cracks, buried in a medium has been recently proposed. The method called fundamental wave amplitude difference (FAD) consists of a sequence of acquisitions with different subsets of elements for each line of the image. An image revealin...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.02.003
更新日期：2019-07-01 00:00:00
abstract：:The wave propagation of an infinite functionally graded plate in thermal environments is studied using the higher-order shear deformation plate theory. The thermal effects and temperature-dependent material properties are both taken into account. The temperature field considered is assumed to be a uniform distribution...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2011.05.009
更新日期：2011-12-01 00:00:00
abstract：:Ultrasonic cutting is widely used in food processing applications to produce a clean and accurate cut. However, it is yet to be adopted as an instrument of choice in orthopaedic applications, mainly due to the high temperatures that can be generated at the cut site and the consequent requirement to use additional cool...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2006.06.046
更新日期：2006-12-22 00:00:00
abstract：:This paper describes ultrasonic measurements of normal and tangential stiffnesses of the contacting interface between polished aluminum blocks subjected to nominal contact pressures up to about 3.8 MPa. These stiffnesses were evaluated by ultrasonic spectroscopy methods for the bulk (longitudinal and transverse) wave ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2007.08.005
更新日期：2007-12-01 00:00:00
abstract：:The accurate estimation of time of flight (TOF) of an ultrasonic signal is essential in ultrasonic non-destructive testing (NDT). A novel method for TOF estimation based on the short-time Fourier transform (STFT) is proposed in this paper. Firstly, the time and frequency components of ultrasonic echoes are represented...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2020.106104
更新日期：2020-04-01 00:00:00
abstract：:The numerical studies conducted in this paper are based on our previous research (Chen et al., 2017); through use of the spectral element method, parametric sensitivity studies of Nonlinear Coda Wave Interferometry (NCWI) are established here and divided into two parts. In the first part, CWI observables are found to ...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2019.105968
更新日期：2019-11-01 00:00:00
abstract：:Geometrical and material property changes cause deviations in the resonant conditions used for noncollinear wave mixing. These deviations are predicted and observed using the SV(ω1)+L(ω2)→L(ω1+ω2) interaction, where SV and L are the shear vertical and longitudinal waves, respectively, and ω1, ω2 are their frequencies....
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.11.009
更新日期：2015-03-01 00:00:00
abstract：:Both pinnae of anaesthetized male guinea-pigs were contused in a reproducible manner and one immediately treated with 0.75 MHz ultrasound at an average therapeutic intensity of 0.61 W cm-2 for a period of 2 min. The lividity and rate of resorption of the rusultant bruises were measured by a photometric method. The res...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(78)90021-5
更新日期：1978-09-01 00:00:00
abstract：:A nonlinear acoustic method to assess the damage level of a complex medium is discussed herein. Thanks to the highly nonlinear elastic signatures of cracks or, more generally, internal solid contacts, this method is able to distinguish between contributions from linear wave scattering by a heterogeneity and contributi...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2016.09.015
更新日期：2017-01-01 00:00:00
abstract：:This paper proposes a new pair of sequences whose cross-correlation values are zero except for the peak value and presents a new modulation method for an ultrasonic Doppler flowmeter with high sensitivity utilizing these sequences. In this method, transmitted and received waves are modulated and demodulated, respectiv...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(79)90023-4
更新日期：1979-11-01 00:00:00
abstract：:It has been suggested that viscous losses, caused by the motion of myofibrils relative to their environmental fluid, could be the major cause of ultrasound attenuation in muscle. This Paper presents theoretical and experimental estimates of the viscous component of attenuation in suspensions of myofibrils. Experimenta...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/0041-624x(88)90046-7
更新日期：1988-01-01 00:00:00
abstract：:Shear-Horizontally (SH) polarized, ultrasonic, guided wave modes are considered in order to infer changes in the adhesive properties at several interfaces located within an adhesive bond joining two metallic plates. Specific aluminium lap-joint samples were produced, with different adhesive properties at up to four in...
journal_title：Ultrasonics
pub_type： 杂志文章
doi：10.1016/j.ultras.2014.03.002
更新日期：2014-09-01 00:00:00
